Users Guide
Table Of Contents
- Dell EMC iDRAC Service Module 3.2 User’s Guide
- Contents
- Introduction
- Preinstallation setup
- Installing the iDRAC Service Module
- Initial installation of iDRAC Service Module through iDRAC for Windows
- Initial installation of iSM through iDRAC Express
- Initial installation of iDRAC Service Module via iDRAC for Linux
- Installing the iDRAC Service Module on Microsoft Windows operating systems
- Installing the iDRAC Service Module on Microsoft Windows operating systems
- Modifying the iDRAC Service Module components on Microsoft Windows operating systems
- Repairing the iDRAC Service Module on Microsoft Windows operating systems
- Uninstalling the iDRAC Service Module on Microsoft Windows operating systems
- Installing iDRAC Service Module on supported Linux operating system
- Installing the iDRAC Service Module on VMware ESXi
- Installing the iDRAC Service Module on Citrix XenServer
- Installing iDRAC Service Module when the System Configuration Lock Down Mode is enabled
- Configuring the iDRAC Service Module
- iDRAC Service Module monitoring features
- Operating system information
- Lifecycle Controller log replication into operating system
- Automatic System Recovery
- Windows Management Instrumentation Providers
- Prepare to remove NVMe PCIe SSD device
- Remote iDRAC hard reset
- iDRAC access via Host OS
- In-band support for iDRAC SNMP alerts
- Enable WSMAN Remotely
- Auto-updating iDRAC Service Module
- FullPowerCycle
- SupportAssist on the Box
- Enabling the In-band SNMP Get feature—Linux
- Enabling the In-band SNMP Get feature—Windows
- iDRAC GUI Launcher
- Frequently asked questions
- Linux and Ubuntu installer packages
3. If you do not want to continue the installation, enter q to quit.
NOTE: After installing different features, you can also modify the same.
NOTE: To know if iDRAC Service Module is installed on your Linux operating system, run the command /etc/init.d/
dcismeng status. If the iDRAC Service Module is installed and running, the status running is displayed.
NOTE: Use the systemctl status dcismeng.service command instead of the init.d command to check if the
iDRAC Service Module is installed on RedHat Enterprise Linux 7 or SUSE Linux Enterprise 12 operating system.
NOTE:
You must provide a unique port number between the range 1024 to 65535 if you chose to install iDRAC access via Host
OS feature. If you do not provide a port number, port number 1266 or a previously configured port (if any) is assigned by
default.
NOTE: if OpenManage Server Administrator (OMSA) is already installed on 1311, the same port could not be utilized for
iDRAC Service module.
Silent installation
You can install the iDRAC Service Module silently in the background without a user console. This can be achieved by using
setup.sh with parameters.
The parameters that can be passed to use setup.sh are:
Table 8. Silent installation
Parameter Description
-h Help: Displays the help
-i Install: Installs and enables the selected features
-x Express: Installs and enables all available features
-d Delete: Uninstall the iDRAC Service Module component
-w Automatic System Recovery: Enables the Automatic System
Recovery Instrumentation Service
-I LC LOG: Enables the Lifecycle Log Replication
-o OS Information: Enables the Operating System Information
-a Autostart: Start the installed service after the component has
been installed
-O iDRAC access via Host OS: Enables the iDRAC access via
Host OS feature
-s Enables the in-band SNMP traps
-g Enables access via SNMP Get
NOTE: On Linux operating systems, if a feature modifying operation with silent option is enabled from the Linux webpack
(using setup.sh), then the previously enabled feature states will be overridden by the new features select during modifying
operation.
Uninstalling the iDRAC Service Module on Linux operating system
The iDRAC Service Module can be uninstalled in two different methods:
● Using uninstall script
● Using RPM command
22
Installing the iDRAC Service Module