Concept Guide

reachable (via Te 1/32)
seq 35 redirect 155.1.1.2 track 5 ip 7.7.7.0/24 8.8.8.0/24, Track 5 [up], Next-hop reachable
(via Po 5)
seq 30 redirect 155.1.1.2 track 6 icmp host 8.8.8.8 any, Track 5 [up], Next-hop reachable (via
Po 5)
seq 35 redirect 42.1.1.2 icmp host 8.8.8.8 any, Next-hop reachable (via Vl 20)
seq 40 redirect 43.1.1.2 tcp 155.55.2.0/24 222.22.2.0/24, Next-hop reachable (via Vl 30)
seq 45 redirect 31.1.1.2 track 200 ip 12.0.0.0 255.0.0.197 13.0.0.0 255.0.0.197, Track 200
[up], Next-hop reachable (via Te 1/32)
, Track 200
[up], Next-hop reachable (via Vl 20)
, Track 200
[up], Next-hop reachable (via Po 5)
, Track 200
[up], Next-hop reachable (via Po 7)
, Track 200
[up], Next-hop reachable (via Te 2/18)
, Track 200
[up], Next-hop reachable (via Te 2/19)
Use the show ip redirect-list (without the list name) to display all the redirect-lists congured on the device.
Dell#show ip redirect-list
IP redirect-list rcl0:
Defined as:
seq 5 permit ip 200.200.200.200
200.200.200.200 199.199.199.199 199.199.199.199
seq 10 redirect 1.1.1.2 tcp 234.224.234.234 255.234.234.234 222.222.222.222/24
seq 40 ack, Next-hop reachable (via Te 8/1), ARP resolved
Applied interfaces:
Te 8/0
NOTE
: If, the redirect-list is applied to an interface, the output of show ip redirect-list redirect-list-name command displays
reachability and ARP status for the specied next-hop.
Showing CAM PBR Conguration Example :
Dell#show cam pbr stack-unit 1 port-set 0
TCP Flag: Bit 5 - URG, Bit 4 - ACK, Bit 3 - PSH, Bit 2 - RST, Bit 1 - SYN, Bit 0 - FIN
Cam Port VlanID Proto Tcp Src Dst SrcIp DstIp Next-hop Egress
Index Flag Port Port MAC Port
------------------------------------------------------------------------------------------------
-----------------
06080 0 N/A IP 0x0 0 0 200.200.200.200
200.200.200.200 199.199.199.199 199.199.199.199
N/A NA
06081 0 N/A TCP 0x10 0 40 234.234.234.234 255.234.234.234 222.222.222.222/
24
00:00:00:00:00:09 8/1
Apply a Redirect-list to an Interface using a Redirect-
group
IP redirect lists are supported on physical interfaces as well as virtual local area network (VLAN) and port-channel interfaces.
NOTE
: When you apply a redirect-list on a port-channel, when trac is redirected to the next hop and the destination port-
channel is shut down, the trac is dropped. However, the trac redirected to the destination port-channel is sometimes
switched.
To apply a redirect list to an interface, use the following command. You can apply multiple redirect-lists can be applied to a redirect-group. It
is also possible to create two or more redirect-groups on one interface for backup purposes.
Apply a redirect list (policy-based routing) to an interface.
INTERFACE mode
Policy-based Routing (PBR)
611