Owners Manual
Table Of Contents
- PowerVault NX3240 Network Attached Storage System Installation and Service Manual
- Contents
- NX3240 system overview
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- Viewing System BIOS
- System BIOS Settings details
- System Information
- Viewing System Information
- System Information details
- Memory Settings
- Viewing Memory Settings
- Memory Settings details
- Processor Settings
- Viewing Processor Settings
- Processor Settings details
- SATA Settings
- Viewing SATA Settings
- SATA Settings details
- Boot Settings
- Viewing Boot Settings
- Boot Settings details
- Choosing system boot mode
- Changing boot order
- Integrated Devices
- Viewing Integrated Devices
- Integrated Devices details
- Serial Communication
- Viewing Serial Communication
- Serial Communication details
- System Profile Settings
- Viewing System Profile Settings
- System Profile Settings details
- System Security
- Viewing System Security
- System Security Settings details
- Creating a system and setup password
- Using your system password to secure your system
- Deleting or changing system and setup password
- Operating with setup password enabled
- Miscellaneous Settings
- Viewing Miscellaneous Settings
- Miscellaneous Settings details
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- Front bezel
- System cover
- Backplane cover
- Air shroud
- Cooling fan assembly
- Cooling fans
- Intrusion switch
- Mid drive tray
- Removing the mid drive tray
- Installing the mid drive tray
- Removing a drive blank from the drive carrier
- Installing a drive blank into the drive carrier
- Removing a drive carrier from the mid drive tray
- Installing a drive carrier into the mid drive tray
- Removing a 3.5-inch drive from the drive carrier
- Installing a 3.5-inch drive into the drive carrier
- Drives
- Removing a drive blank
- Installing a drive blank
- Removing a drive carrier
- Installing a drive carrier
- Removing a 2.5-inch drive from the 3.5-inch drive adapter
- Installing a 2.5-inch drive into the 3.5-inch drive adapter
- Removing a 3.5-inch adapter from a 3.5-inch drive carrier
- Installing a 3.5-inch adapter into a 3.5-inch drive carrier
- Removing the drive from the drive carrier
- Installing a drive into the drive carrier
- Rear drive cage
- System memory
- Processors and heat sinks
- Expansion cards and expansion card risers
- Expansion card installation guidelines
- Opening and closing the PCIe card holder latch
- Removing the expansion card from the expansion card riser
- Installing the expansion card into the expansion card riser
- Removing the riser 2 blank
- Installing the riser 2 blank
- Removing the expansion card riser 1
- Installing the expansion card riser 1
- Removing the expansion card riser 2
- Installing the expansion card riser 2
- Network daughter card
- Integrated storage controller card
- Backplane
- System battery
- Power supply units
- System board
- Trusted Platform Module
- Control panel
- Diagnostics and indicators
- Jumpers and connectors
- Getting help
Figure 31. Installing a 3.5-inch drive into the drive carrier
Next steps
Follow the procedure listed in After working inside your system.
Drives
Drives are supplied in hot swappable drive carriers that fit in the drive slots.
CAUTION:
Before attempting to remove or install a drive while the system is running, see the documentation for
the storage controller card to ensure that the host adapter is configured correctly.
CAUTION: Do not turn off or restart your system while a drive is being formatted. Doing so can cause a drive
failure.
When you format a drive, allow enough time for the formatting to complete. Be aware that high-capacity drives can take a long
time to format.
This section contains information about the removal and installation of the hard-drive blank, hot-swappable hard drive, the
removal and installation of the hard drive from the hard-drive carrier.
Removing a drive blank
Prerequisites
1. Follow the safety guidelines listed in Safety instructions.
2. If installed, remove the front bezel.
CAUTION: To maintain proper system cooling, drive blanks must be installed in all empty drive slots.
CAUTION: Mixing drive blanks from previous generations of NAS systems is not supported.
Installing and removing system components 69