Owners Manual
Table Of Contents
- PowerVault NX3240 Network Attached Storage System Installation and Service Manual
- Contents
- NX3240 system overview
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- Viewing System BIOS
- System BIOS Settings details
- System Information
- Viewing System Information
- System Information details
- Memory Settings
- Viewing Memory Settings
- Memory Settings details
- Processor Settings
- Viewing Processor Settings
- Processor Settings details
- SATA Settings
- Viewing SATA Settings
- SATA Settings details
- Boot Settings
- Viewing Boot Settings
- Boot Settings details
- Choosing system boot mode
- Changing boot order
- Integrated Devices
- Viewing Integrated Devices
- Integrated Devices details
- Serial Communication
- Viewing Serial Communication
- Serial Communication details
- System Profile Settings
- Viewing System Profile Settings
- System Profile Settings details
- System Security
- Viewing System Security
- System Security Settings details
- Creating a system and setup password
- Using your system password to secure your system
- Deleting or changing system and setup password
- Operating with setup password enabled
- Miscellaneous Settings
- Viewing Miscellaneous Settings
- Miscellaneous Settings details
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- Front bezel
- System cover
- Backplane cover
- Air shroud
- Cooling fan assembly
- Cooling fans
- Intrusion switch
- Mid drive tray
- Removing the mid drive tray
- Installing the mid drive tray
- Removing a drive blank from the drive carrier
- Installing a drive blank into the drive carrier
- Removing a drive carrier from the mid drive tray
- Installing a drive carrier into the mid drive tray
- Removing a 3.5-inch drive from the drive carrier
- Installing a 3.5-inch drive into the drive carrier
- Drives
- Removing a drive blank
- Installing a drive blank
- Removing a drive carrier
- Installing a drive carrier
- Removing a 2.5-inch drive from the 3.5-inch drive adapter
- Installing a 2.5-inch drive into the 3.5-inch drive adapter
- Removing a 3.5-inch adapter from a 3.5-inch drive carrier
- Installing a 3.5-inch adapter into a 3.5-inch drive carrier
- Removing the drive from the drive carrier
- Installing a drive into the drive carrier
- Rear drive cage
- System memory
- Processors and heat sinks
- Expansion cards and expansion card risers
- Expansion card installation guidelines
- Opening and closing the PCIe card holder latch
- Removing the expansion card from the expansion card riser
- Installing the expansion card into the expansion card riser
- Removing the riser 2 blank
- Installing the riser 2 blank
- Removing the expansion card riser 1
- Installing the expansion card riser 1
- Removing the expansion card riser 2
- Installing the expansion card riser 2
- Network daughter card
- Integrated storage controller card
- Backplane
- System battery
- Power supply units
- System board
- Trusted Platform Module
- Control panel
- Diagnostics and indicators
- Jumpers and connectors
- Getting help
System Security
You can use the System Security screen to perform specific functions such as setting the system password, setup password
and disabling the power button.
Viewing System Security
To view the System Security screen, perform the following steps:
Steps
1. Turn on or restart your system.
2. Press F2 immediately after you see the following message:
F2 = System Setup
NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then
restart your system and try again.
3. On the System Setup Main Menu screen, click System BIOS.
4. On the System BIOS screen, click System Security.
System Security Settings details
The System Security Settings screen provides the following options.
Option
Description
In-Band
Manageability
Interface
When set to Disabled, this setting will hide the Management Engine's (ME), HECI devices, and the
system's IPMI devices from the operating system. This prevents the operating system from changing the
ME power capping settings, and blocks access to all in-band management tools. All management should
be managed through out-of-band. This option is set to Enabled by default.
NOTE: BIOS update requires HECI devices to be operational and DUP updates require IPMI interface
to be operational. This setting needs to be set to Enabled to avoid updating errors.
Intel(R) AES-NI Improves the speed of applications by performing encryption and decryption by using the Advanced
Encryption Standard Instruction Set (AES-NI). This option is set to Enabled by default.
System
Password
Sets the system password. This option is set to Enabled by default and is read-only if the password
jumper is not installed in the system.
Setup Password Sets the setup password. This option is read-only if the password jumper is not installed in the system.
Password Status Locks the system password. This option is set to Unlocked by default.
TPM Security
NOTE: The TPM menu is available only when the TPM module is installed.
Enables you to control the reporting mode of the TPM. The TPM Security option is set to Off by
default. You can only modify the TPM Status TPM Activation, and the Intel SGX fields if the TPM Status
field is set to either On with Pre-boot Measurements or On without Pre-boot Measurements.
When TPM 1.2 is installed, the TPM Security option is set to Off, On with Pre-boot Measurements,
or On without Pre-boot Measurements.
When TPM 2.0 is installed, the TPM Security option is set to On or Off. This option is set to Off by
default.
Intel(R) TXT Enables or disables the Intel Trusted Execution Technology (TXT) option. To enable the Intel TXT option,
virtualization technology and TPM Security must be enabled with Pre-boot measurements. This option is
set to Off by default.
When TPM 2.0 is installed, TPM 2 Algorithm option is available. It enables you to select a hash algorithm
from those supported by the TPM (SHA1, SHA256). TPM 2 Algorithm option must be set to SHA256,
to enable TXT.
40 Pre-operating system management applications