Deployment Guide
Table Of Contents
- Dell EMC PowerVault ME4 Series Storage System Deployment Guide
- Contents
- Before you begin
- Mount the enclosures in the rack
- Connect to the management network
- Cable host servers to the storage system
- Cabling considerations
- Connecting the enclosure to hosts
- Host connection
- Connect power cables and power on the storage system
- Perform system and storage setup
- Record storage system information
- Using guided setup
- Web browser requirements and setup
- Access the PowerVault Manager
- Update firmware
- Use guided setup in the PowerVault Manager Welcome panel
- Perform host setup
- Host system requirements
- Windows hosts
- Configuring a Windows host with FC HBAs
- Configuring a Windows host with iSCSI network adapters
- Configuring a Windows host with SAS HBAs
- Linux hosts
- Configuring a Linux host with FC HBAs
- Configure a Linux host with iSCSI network adapters
- Attach a Linux host with iSCSI network adapters to the storage system
- Assign IP addresses for each network adapter connecting to the iSCSI network
- Register the Linux host with iSCSI network adapters and create volumes
- Enable and configure DM Multipath on the Linux host with iSCSI network adapters
- Create a Linux file system on the volumes
- SAS host server configuration for Linux
- VMware ESXi hosts
- Fibre Channel host server configuration for VMware ESXi
- iSCSI host server configuration for VMware ESXi
- Attach an ESXi host with network adapters to the storage system
- Configure the VMware ESXi VMkernel
- Configure the software iSCSI adapter on the ESXi host
- Register an ESXi host with a configured software iSCSI adapter and create and map volumes
- Enable multipathing on an ESXi host with iSCSI volumes
- Volume rescan and datastore creation for an ESXi hosts with iSCSI network adapters
- SAS host server configuration for VMware ESXi
- Citrix XenServer hosts
- Fibre Channel host server configuration for Citrix XenServer
- iSCSI host server configuration for Citrix XenServer
- Attach a XenServer host with network adapters to the storage system
- Configure a software iSCSI adapter on a XenServer host
- Configure the iSCSI IQN on a XenServer host
- Enable Multipathing on a XenServer host
- Register a XenServer host with a software iSCSI adapter and create volumes
- Create a Storage Repository for a volume on a XenServer host with a software iSCSI adapter
- SAS host server configuration for Citrix XenServer
- Troubleshooting and problem solving
- Locate the service tag
- Operators (Ops) panel LEDs
- Initial start-up problems
- Cabling for replication
- SFP+ transceiver for FC/iSCSI ports
- System Information Worksheet
- Setting network port IP addresses using the CLI port and serial cable
Figure 13. Cabling connections between a 2U controller enclosure and 2U expansion enclosures
1.
Controller module A (0A) 2. Controller module B (0B)
3. IOM (1A) 4. IOM (1B)
5. IOM (2A) 6. IOM (2B)
7. IOM (3A) 8. IOM (3B)
9. IOM (9A) 10. IOM (9B)
Cabling connections between a 5U controller enclosure and 5U expansion enclosures on page 19 shows the maximum
cabling configuration for a 5U84 controller enclosure with 5U84 expansion enclosures (four enclosures including the controller
enclosure).
Figure 14. Cabling connections between a 5U controller enclosure and 5U expansion enclosures
1.
Controller module A (0A) 2. Controller module B (0B)
3. IOM (1A) 4. IOM (1B)
5. IOM (2A) 6. IOM (2B)
7. IOM (3A) 8. IOM (3B)
Mount the enclosures in the rack 19