Manualshelf

Users Guide

ManualsBrandsDell ManualsAccess PlatformsEMC Networking MX9116n
1811181218131814181518161817181818191820
Table Of Contents
Example
OS10# show trace
May 23 17:10:03 OS10 base_nas: [NETLINK:NH-
EVENT]:ds_api_linux_neigh.c:nl_to_nei
gh_info:109, Operation:Add-NH family:IPv4(2) flags:0x0 state:Failed(32)
if-idx:4
May 23 17:10:03 OS10 base_nas: [NETLINK:NH-
EVENT]:ds_api_linux_neigh.c:nl_to_nei
gh_info:120, NextHop IP:192.168.10.1
May 23 17:10:04 OS10 base_nas: [NDI:NDI-SAI], Values are invalid - can't
be conv
erted to SAI types (func:2359304)
May 23 17:10:04 OS10 base_nas: [NDI:NDI-SAI], Hash value - 20 can't be
converted
May 23 17:10:04 OS10 base_nas: [NDI:NDI-SAI], Values are invalid - can't
be conv
erted to SAI types (func:2359305)
May 23 17:10:04 OS10 base_nas: [NDI:NDI-SAI], Values are invalid - can't
be conv
erted to SAI types (func:2359311)
May 23 17:10:04 OS10 base_nas: [NDI:NDI-SAI], Hash value - 20 can't be
converted
May 23 17:10:04 OS10 base_nas: [NDI:NDI-SAI], Values are invalid - can't
be conv
erted to SAI types (func:2359312)
May 23 17:10:04 OS10 base_nas: [NDI:NDI-SAI], Invalid operation type for
NDI (23
59344)
May 23 17:10:04 OS10 base_nas: [NDI:NDI-SAI], Invalid operation type for
NDI (23
59345)
May 23 17:10:04 OS10 base_nas: [NDI:NDI-SAI], Invalid operation type for
NDI (23
59346)
May 23 17:10:04 OS10 base_nas: [NDI:NDI-SAI], Invalid operation type for
NDI (23
59319)
May 23 17:10:08 OS10 base_nas: [NETLINK:NH-
EVENT]:ds_api_linux_neigh.c:nl_to_nei
--More--
Supported
Releases
10.2.0E or later
Monitor CPU Utilization
You can set CPU thresholds so that alarms are triggered when CPU utilization reaches the high or low threshold level. CPU
utilization is monitored as a running average percentage over predefined intervals of five seconds, one minute, and five minutes.
By default, this feature is enabled with a higher threshold value so that alarms do not generate frequently.
When CPU utilization crosses the high threshold, a critical alarm triggers. A warning alarm triggers when CPU utilization crosses
the low threshold. The alarms clear when CPU utilization goes below the corresponding threshold. To view the current active
alarms in the system, use the show alarms command.
The util-threshold cpu command allows you to configure the high and low threshold values. Before configuring the
threshold values, configure a syslog server to collect and store the syslog messages. To view the configured CPU utilization
thresholds, use the show util-threshold cpu command.
NOTE:
During image installation, upgrade, or reload with default threshold values, CPU utilization might cross the threshold
values and therefore trigger alarms. These alarms eventually clear after the installation, upgrade, or reload is completed.
Example of configuring CPU utilization threshold values
OS10# configure terminal
OS10(config)# logging server 10.10.10.11
OS10(config)# util-threshold cpu 1min high 10 low 5
OS10(config)# util-threshold cpu 5min high 80 low 70
OS10(config)# exit
OS10# show util-threshold cpu
1820
Troubleshoot Dell EMC SmartFabric OS10