Users Guide
Table Of Contents
- 1 Introduction
- 2 SmartFabric Services for PowerEdge MX: An overview
- 3 SmartFabric mode requirements, guidelines, and restrictions
- 3.1 Create multi-chassis management group
- 3.2 Upstream network requirements
- 3.3 VLAN scaling guidelines
- 3.4 Configuring port speed and breakout
- 3.5 Switch slot placement for SmartFabric mode
- 3.6 Switch-to-Switch cabling
- 3.7 NIC teaming guidelines
- 3.8 Maximum Transmission Unit (MTU) behavior
- 3.9 Other restrictions and guidelines
- 4 Creating a SmartFabric
- 4.1 Physically cable MX chassis and upstream switches
- 4.2 Define VLANs
- 4.3 Create the SmartFabric
- 4.4 Configure uplink port speed or breakout, if needed
- 4.5 Create Ethernet uplink
- 4.6 Configure Fibre Channel universal ports
- 4.7 Create Fibre Channel uplinks
- 4.8 Configuring the upstream switch and connect uplink cables
- 5 Deploying a server
- 6 SmartFabric operations
- 7 Switch operations
- 8 Validating the SmartFabric deployment
- 9 SmartFabric troubleshooting
- 9.1 Troubleshooting errors encountered for port group breakout
- 9.2 Troubleshooting Spanning Tree Protocol (STP)
- 9.3 Verify VLT/vPC configuration on upstream switches
- 9.4 Discovery of FEM and compute sleds
- 9.5 Troubleshooting uplink errors
- 9.6 Troubleshooting FC/FCoE
- 9.7 SmartFabric Services – Troubleshooting commands
- 10 Uplink configuration scenarios
- 10.1 Scenario 1 - SmartFabric deployment with Dell EMC PowerSwitch Z9100-ON upstream switches
- 10.2 Scenario 2 - SmartFabric connected to Cisco Nexus 3232C switches
- 10.3 Scenario 3: Connect MX9116n FSE to Fibre Channel storage - NPIV Proxy Gateway mode
- 10.4 Scenario 4: Connect MX9116n FSE to Fibre Channel storage - FC Direct Attach
- 10.5 Scenario 5: Connect MX5108n to Fibre Channel storage - FSB
- 10.6 Scenario 6: Configure Boot from SAN
- A Hardware used in this document
- B Dell EMC Unity information
- C Additional information
- D Validated components
- E Technical resources
- F Support and feedback
93 Dell EMC PowerEdge MX SmartFabric Configuration and Troubleshooting Guide
Configured hello time 2, max age 20, forward delay 15
Flush Interval 200 centi-sec, Flush Invocations 432
Flush Indication threshold 0 (MAC flush optimization is disabled)
Interface Designated
Name PortID Prio Cost Sts Cost Bridge ID PortID
--------------------------------------------------------------------------------
port-channel1 128.2517 128 50 FWD 0 32768 2004.0f00
Interface
Name Role PortID Prio Cost Sts Cost Link-type Edge
--------------------------------------------------------------------------------
port-channel1 Root 128.2517 128 50 FWD 0 AUTO No
VLAN 10
Executing IEEE compatible Spanning Tree Protocol
Root ID Priority 32778, Address 4c76.25e8.e840
Root Bridge hello time 2, max age 20, forward delay 15
Bridge ID Priority 32778, Address 4c76.25e8.f2c0
Configured hello time 2, max age 20, forward delay 15
Flush Interval 200 centi-sec, Flush Invocations 5
Flush Indication threshold 0 (MAC flush optimization is disabled)
Interface Designated
Interface Designated
Name PortID Prio Cost Sts Cost Bridge ID PortID
--------------------------------------------------------------------------------
port-channel1 128.2517 128 50 FWD 1 32768 2004.0f00
Interface
Name Role PortID Prio Cost Sts Cost Link-type Edge
--------------------------------------------------------------------------------
port-channel1 Root 128.2517 128 50 FWD 1 AUTO No