Service Manual

ManualsBrandsDell ManualsConverged InfrastructureEmbedded Box PC 5000

Dell Embedded Box PC

5000

Service Manual

Regulatory Model: N01PC

Regulatory Type: N01PC001

Summary of content (100 pages)

PAGE 1
Dell Embedded Box PC 5000 Service Manual Regulatory Model: N01PC Regulatory Type: N01PC001
PAGE 2
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2017 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
PAGE 3
Contents 1 Before working inside your Embedded Box PC.................................................................................9 Before you begin....................................................................................................................................................................9 Safety instructions.................................................................................................................................................................
PAGE 4
12 Removing the interposer board.................................................................................................. 24 Prerequisites.........................................................................................................................................................................24 Procedure.............................................................................................................................................................................
PAGE 5
Procedure............................................................................................................................................................................. 43 24 Replacing the WWAN-antenna connectors..................................................................................45 Procedure.............................................................................................................................................................................
PAGE 6
Procedure............................................................................................................................................................................. 63 36 Replacing the intrusion switch...................................................................................................64 Procedure.............................................................................................................................................................................
PAGE 7
Procedure.............................................................................................................................................................................80 48 Replacing the top cover............................................................................................................ 82 Procedure.............................................................................................................................................................................
PAGE 8
Peripherals............................................................................................................................................................................99 WLAN/WWAN...................................................................................................................................................................100 Zigbee................................................................................................................................................
PAGE 9
1 Before working inside your Embedded Box PC NOTE: The images in this document may differ from your Embedded Box PC depending on the configuration you ordered. Topics: • • • • Before you begin Safety instructions Recommended tools Screw list Before you begin 1. Save and close all open files and exit all open applications. 2. Shut down the Embedded Box PC. The shut-down instruction varies depending on the operating system installed on the Embedded Box PC.
PAGE 10
CAUTION: Press and eject any installed card from the media-card reader. Recommended tools The procedures in this document may require the following tools: • • • • • • Philips screwdriver Flat-head screwdriver Plastic scribe Hex screwdriver 8 mm open wrench 10 mm open wrench Screw list The following table provides the list of screws used for securing different components to the Embedded Box PC.
PAGE 11
Component Secured to Screw type Quantity Hard-drive cage Back cover M3x5 4 Top hard drive/solid-state drive Hard-drive cage STDF(L5.1), M3x3 4 Bottom hard drive/solid-state drive Hard-drive cage STDF(L5.
PAGE 12
2 After working inside your Embedded Box PC CAUTION: Leaving stray or loose screws inside your Embedded Box PC may severely damage your Embedded Box PC. 1. Replace all screws and ensure that no stray screws remain inside the Embedded Box PC. 2. Connect any external devices, peripherals, or cables you removed before working on the Embedded Box PC. 3. Connect your Embedded Box PC and all attached devices to their electrical outlets. 4. Turn on the Embedded Box PC.
PAGE 13
3 Technical overview NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • System-board components System-board components 1. 3. 5. 7. 9. 11. 13. 15.
PAGE 14
4 Removing the back cover NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • Procedure Procedure 1.
PAGE 15
1. back cover 3. routing guide 5. SATA-power cable 2. hard drive/Solid-state drive assembly 4. SATA-data cable 5. Close the back cover partially and push the back cover forward to release it from the tabs on the chassis. 6. Lift the back cover off the chassis. a. back cover b. chassis 7. Remove the Removing the hard-drive cage.
PAGE 16
5 Replacing the back cover NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • Procedure Procedure 1. Replace the hard-drive cage. 2.
PAGE 17
6 Removing the hard-drive cage NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. CAUTION: Hard drives/solid-state drives are fragile.
PAGE 18
7 Replacing the hard-drive cage NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. CAUTION: Hard drives/solid-state drives are fragile.
PAGE 19
8 Removing the drives from the hard-drive cage NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. CAUTION: Hard drives/solid-state drives are fragile.
PAGE 20
1. back cover 3. drive cage 20 Removing the drives from the hard-drive cage 2. STDF (L5.1), M3x3 screws(4) 4.
PAGE 21
9 Replacing the drives in to the hard-drive cage NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. CAUTION: Hard drives/solid-state drives are fragile.
PAGE 22
10 Removing the solid-state drive from bracket NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. CAUTION: Solid-state drives are fragile.
PAGE 23
11 Replacing the solid-state drive in to bracket NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. CAUTION: Solid-state drives are fragile.
PAGE 24
12 Removing the interposer board NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 25
13 Replacing the interposer board NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Procedure Post-requisites Procedure 1.
PAGE 26
14 Installing a PCI/PCIe card NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. CAUTION: PCI/PCIe cards are fragile. Exercise care when handling the cards.
PAGE 27
1. M3x5 countersunk screw 3. filler plate 2. PCI/PCIe filler-plate bracket 4. chassis 5. Install the PCIe or PCI cards in their respective slots on the riser board. a. riser card b. PCIe card slot c. PCIe card 6. Replace the filler plate for an empty card slot. 7. Replace the filler-plate bracket on the chassis. 8. Replace the screw that secures the bracket to the chassis.
PAGE 28
1. filler bracket 3. chassis 2. bracket 4. M3x5 countersunk screw 9. Replace the screws that secure the PCIe card and the filler plate to the chassis. a. chassis b. filler plate c. M3x5 countersunk screws (2) Post-requisites Follow step 2 to step 8 in “Replacing the back cover”.
PAGE 29
15 Removing the PCI/PCIe card NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
PAGE 30
1. M3x5 countersunk screw 3. filler plate 2. bracket 4. chassis 5. Release the PCI/PCIe card from the PCI/PCIe card slot on the riser card and lift it off the chassis. 1. PCIe card 3. riser card 30 Removing the PCI/PCIe card 2. PCIe card-slot 4.
PAGE 31
16 Replacing the PCIe card NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Procedure Post-requisites Procedure 1.
PAGE 32
1. filler plate 3. chassis 2. fillet-plate bracket 4. M3x5 countersunk screw 5. Replace the screws that secure the PCI/PCIe card and the filler plate to the chassis. a. chassis b. filler plate c. M3x5 countersunk screws (2) Post-requisites Follow step 2 to step 8 in “Replacing the back cover”.
PAGE 33
17 Removing the memory module NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 34
c.
PAGE 35
18 Replacing the memory module NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Procedure Post-requisites Procedure 1.
PAGE 36
Post-requisites 1. Replace the PCI/PCIe card (if necessary). 2. Follow step 2 to step 8 in “Replacing the back cover”.
PAGE 37
19 Removing the WLAN-antenna connectors NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 38
a. antenna cables b. routing guide c.
PAGE 39
20 Replacing the WLAN-antenna connectors NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Procedure Post-requisites Procedure 1.
PAGE 40
21 Removing the WLAN card NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 41
22 Replacing the WLAN card NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
PAGE 42
1. tab 3. WLAN card 5. M2x3 screws (2) Post-requisites 1. Replace the PCI/PCIe card (if necessary). 2. Follow step 2 to step 8 in “Replacing the back cover”. 42 Replacing the WLAN card 2. notch 4. WLAN-card bracket 6.
PAGE 43
23 Removing the WWAN-antenna connectors NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 44
a. WWAN-antenna cables (2) b. routing guide c.
PAGE 45
24 Replacing the WWAN-antenna connectors NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Procedure Post-requisites Procedure 1.
PAGE 46
25 Removing the WWAN card NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 47
3. mPCIE1 slot 4.
PAGE 48
26 Replacing the WWAN card NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
PAGE 49
1. tab 3. M2x3 screws (2) 5. WWAN-antenna cables (2) 2. notch 4. WWAN card Post-requisites 1. Replace the PCI/PCIe card (if necessary). 2. Follow step 2 to step 8 in “Replacing the back cover”.
PAGE 50
27 Removing the SIM card NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 51
28 Replacing the SIM card NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Procedure Post-requisites Procedure 1.
PAGE 52
2. Follow step 2 to step 8 in “Replacing the back cover”.
PAGE 53
29 Removing the CANbus cable NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 54
3. routing guides 54 Removing the CANbus cable 4.
PAGE 55
30 Replacing the CANbus cable NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Procedure Post-requisites Procedure 1.
PAGE 56
31 Removing the CANbus card NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 57
1. CANbus card 3. mPCIE1 slot 5. M2x3 screws (2) 2. CANbus cable 4.
PAGE 58
32 Replacing the CANbus card NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Procedure Post-requisites Procedure 1.
PAGE 59
Post-requisites 1. Replace the PCI/PCIe card (if necessary). 2. Follow step 2 to step 8 in “Replacing the back cover”.
PAGE 60
33 Removing the coin-cell battery NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
PAGE 61
c.
PAGE 62
34 Replacing the coin-cell battery NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
PAGE 63
35 Removing the intrusion switch NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 64
36 Replacing the intrusion switch NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Procedure Post-requisites Procedure 1.
PAGE 65
37 Removing the serial ports NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 66
a. chassis b. serial-port connector c.
PAGE 67
38 Replacing the serial ports NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Procedure Post-requisites Procedure 1.
PAGE 68
39 Removing the bottom cover NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 69
40 Replacing the bottom cover NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Procedure Post-requisites Procedure 1.
PAGE 70
41 Removing the riser card NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 71
a. riser-card bracket b. screws (2) c.
PAGE 72
42 Replacing the riser card NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
PAGE 73
Figure 1. DIP switch settings with two PCIe(x8) cards 1. DIP switch 2.
PAGE 74
Figure 2. DIP switch settings with other riser cards 1. DIP switch 2. CPU board 1. Align the screw holes on the bracket with the screw holes on the riser card. 2. Replace the screws that secure the bracket with the riser card. 3. Insert the riser-card assembly in the riser-card slot. 4. Replace the screws that secure the riser-card assembly to the chassis. Post-requisites 1. Replace the PCI/PCIe card (if necessary). 2. Follow step 2 to step 8 in “Replacing the back cover”.
PAGE 75
43 Removing the heat sink NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 76
44 Replacing the heat sink NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Procedure Post-requisites Procedure 1.
PAGE 77
45 Removing the power connectors NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 78
1. chassis 3. routing guide 5. power cable 2. barrel connector 4. M2.5x2 screw 6. grounding cable 6. Remove the screws that secure the power connector to the chassis. 7. Route the power cables along with the barrel connector through the slot on the chassis and remove it from the chassis. a. chassis b. power connector c. M2.
PAGE 79
46 Replacing the power connectors NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Procedure Post-requisites Procedure 1.
PAGE 80
47 Removing the top cover NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 81
4. Remove the top cover off the chassis. a. M3x5 countersunk screws (7) b. top cover c. chassis 5. Remove the power switch.
PAGE 82
48 Replacing the top cover NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Procedure Post-requisites Procedure 1. Replace the power switch. 2.
PAGE 83
49 Removing the power switch NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 84
50 Replacing the power switch NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Procedure Post-requisites Procedure 1.
PAGE 85
51 Removing the CPU board NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 86
52 Replacing the CPU board NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
PAGE 87
53 Removing the system board NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. NOTE: Your Embedded Box PC’s Service Tag is stored in the system board.
PAGE 88
1. serial-port cable 3. SATA power-cable (2) 2. SATA data-cable (2) 4. system board 2. Remove the screws that secure the system board to the chassis. 1. chassis 3. STDF(L8) HEX, M3x4 screws (5) 5. M3x5 screws (8) 3. Lift the system board off the chassis. 88 Removing the system board 2. system board 4.
PAGE 89
a. chassis b.
PAGE 90
54 Replacing the system board NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. NOTE: Your Embedded Box PC’s Service Tag is stored in the system board.
PAGE 91
3. Navigate to the Main tab and enter the Service Tag in the Service Tag Input field.
PAGE 92
55 BIOS setup program Entering BIOS setup program Before turning on the Embedded Box PC, connect the keyboard, mouse, and monitor to the Embedded Box PC, or connect the Embedded Box PC through the KVM session or use Dell Wyse Cloud Client Manager (CCM) or Dell Command | Monitor (DCM) to update the BIOS configuration. 1. Turn on (or restart) the Embedded Box PC. 2. During POST, when the DELL logo is displayed, watch for the F2 prompt to appear, and then press F2 immediately.
PAGE 93
a. jumper plug 8. Follow step 2 to step 9 in “Replacing the back cover”. Clearing CMOS settings 1. Follow step 1 to step 6 in “Removing the back cover”. 2. Locate the CMOS reset jumper (CMOS) on the system board. See “System-board components”. 3. Move the jumper plug from pins 1 and 2 to 2 and 3. 4. Follow step 2 to step 9 in “Replacing the back cover”. 5. Turn on the Embedded Box PC, and wait until the message stating that the CMOS has been cleared appears. 6. Shut down the Embedded Box PC. 7.
PAGE 94
a. jumper plug 8. Follow step 2 to step 8 in “Replacing the back cover”.
PAGE 95
56 Removing the Dell logo board NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Prerequisites Procedure Prerequisites 1.
PAGE 96
a. left chassis b. M3x6 screws (7) c. front chassis 2. Remove the screws that secure the Dell logo board to the front chassis. a. M3x5 screws (3) b. front chassis 3. Remove the Dell logo board from the front chassis.
PAGE 97
a. Dell logo board b.
PAGE 98
57 Replacing the Dell logo board NOTE: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Topics: • • Procedure Post-requisites Procedure 1.
PAGE 99
58 Technology and components Topics: • • • • • • • Power Processor Mechanical Peripherals WLAN/WWAN Zigbee CANbus Power The Dell Embedded Box PC is shipped with the 12-26V DC power adapter. Processor The Dell Embedded Box PC is shipped with Intel Celeron G3900E, Intel Core i3-6100E, Intel Core i5-6440EQ, and Intel Core i7-6820EQ processor. Mechanical The Embedded Box PC is optimized for fanless design, and easy wall/panel and DIN Rail Mount use. It provides easy access to connectors and switches.
PAGE 100
• • • • Mobile Broadband card Mobile WLAN card CANbus card Power adapter WLAN/WWAN The following WLAN and WWAN cards are optionally offered in the Embedded Box PC: • • Dual-band 802.11b/g/n/ac+Bluetooth 4.1 LE Dell Wireless DW5580 HSPA+ Zigbee The Zigbee USB module is a wireless mesh module for Dell Embedded Box PC. CANbus The CANBus daughter card is an optional accessory for Embedded Box PC.