Dell Embedded Box PC 3000 Service Manual Computer Model: Dell Embedded Box PC 3000 Regulatory Model: N02PC Regulatory Type: N02PC001
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2016 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws.
Contents Before working inside your Embedded Box PC..................... 9 Before you begin................................................................................................9 Safety instructions..............................................................................................9 Recommended tools....................................................................................... 10 Screw list..........................................................................................
Removing the interposer board............................................. 28 Prerequisites.................................................................................................... 28 Procedure........................................................................................................ 28 Replacing the interposer board..............................................30 Procedure........................................................................................................
Replacing the WLAN card........................................................ 43 Procedure........................................................................................................ 43 Post-requisites.................................................................................................44 Removing the WWAN card...................................................... 45 Prerequisites.....................................................................................................
Replacing the intrusion switch...............................................60 Procedure........................................................................................................ 60 Post-requisites.................................................................................................60 Removing the I/O plate............................................................ 61 Prerequisites....................................................................................................
Replacing the IET board........................................................... 77 Procedure.........................................................................................................77 Post-requisites................................................................................................. 77 Removing the top cover...........................................................78 Prerequisites...............................................................................................
Replacing the Dell logo board................................................ 92 Procedure........................................................................................................ 92 Post-requisites................................................................................................. 92 BIOS setup program..................................................................93 Entering BIOS setup program.........................................................................
Before working inside your Embedded Box PC NOTE: The images in this document may differ from your Embedded Box PC depending on the configuration you ordered. Before you begin 1 Save and close all open files and exit all open applications. 2 Shut down the Embedded Box PC. The shut-down instruction varies depending on the operating system installed on the Embedded Box PC. NOTE: For more information, see the documentation of your operating system for shut-down instructions.
WARNING: Disconnect all power sources before opening the Embedded Box PC cover or panels. After you finish working inside the Embedded Box PC, replace all covers, panels, and screws before connecting to the electrical outlet. CAUTION: To avoid damaging the Embedded Box PC, ensure that the work surface is flat and clean. CAUTION: To avoid damaging the components and cards, handle them by their edges, and avoid touching pins and contacts.
• 10 mm open wrench Screw list The following table provides the list of screws that are used for securing different components to the Embedded Box PC. Component Secured to Screw type Quantity Logo board Chassis M2x5 3 System board Chassis M2x5 5 System board Chassis STDF (L20) HEX, M2.
Component Secured to Screw type Quantity Solid-state drive bracket Solid-state drive slot M2x3 1 Solid-state drive Solid-state drive bracket M2x3 1 Wall-mount bracket Chassis M3x5 2 Din-rail bracket Back cover M4x7 4 12
After working inside your Embedded Box PC CAUTION: Leaving stray or loose screws inside your Embedded Box PC may severely damage your Embedded Box PC. 1 Replace all screws and ensure that no stray screws remain inside the Embedded Box PC. 2 Connect any external devices, peripherals, or cables you removed before working on the Embedded Box PC. 3 Connect your Embedded Box PC and all attached devices to their electrical outlets. 4 Turn on the Embedded Box PC.
Technical overview WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance.
7 SIM-card slot (SIM) 9 mPCIE two connector (CAN BUS/WLAN/BT) 8 mPCIE one connector (CAN BUS/WWAN) 15
Removing the back cover WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1 Place the Embedded Box PC on a clean and flat surface.
3 Remove the back cover from the chassis by using the two tabs.
Replacing the back cover WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1 Place the back cover on the chassis.
Removing the hard drive WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. CAUTION: Hard drives are fragile. Exercise care when handling the hard drive.
2 3 20 Remove the hard-drive door from the chassis. 1 hard-drive door 3 chassis 2 M2x3 captive screw Remove the screws that secure the hard-drive bracket to the hard drive.
4 Remove the hard drive from the hard-drive bracket.
Replacing the hard drive WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. CAUTION: Hard drives are fragile. Exercise care when handling the hard drive.
Removing the solid-state drive WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. CAUTION: Solid-state drives are fragile.
2 3 24 Remove the hard-drive door from the chassis. 1 hard-drive door 3 chassis 2 M2x3 captive screw Remove the screw that secures the solid-state drive to the solid-state drive bracket.
4 Remove the solid-state drive from the solid-state drive slot.
Replacing the solid-state drive WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. CAUTION: Solid-state drives are fragile.
3 Replace the screw that secures the solid-state drive to the solid-state drive bracket. 1 solid-state drive bracket 2 solid-state drive 3 solid-state drive slot 4 tab 5 notch 4 Place the hard-drive door into the chassis. 5 Tighten the captive screw that secures the hard-drive door to the chassis.
Removing the interposer board WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites Remove the solid-state drive.
2 Remove the interposer board from the solid-state drive card bracket.
Replacing the interposer board WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance.
Removing the solid-state drive card bracket WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1 Remove the solid-state drive.
2 32 Remove the solid-state drive card bracket from the hard-drive bracket.
Replacing the solid-state drive card bracket WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance.
Removing the SIM card WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance.
4 Remove the SIM card from the SIM-card slot.
Replacing the SIM card WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1 Place the SIM card in the SIM-card slot.
Removing the memory module WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites Remove the back cover.
2 38 Remove the memory module from the memory-module slot.
Replacing the memory module WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance.
2 Slide the memory module firmly into the slot at an angle and press the memory module down until it clicks into place. NOTE: If you do not hear the click, remove the memory module and reinstall it. 1 memory-module slot 2 tab 3 notch 4 memory-module Post-requisites Replace the back cover.
Removing the WLAN card WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites Remove the back cover.
4 42 Slide and remove the WLAN card from the mPCIE2 slot.
Replacing the WLAN card WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance.
6 Connect the WLAN-antenna cables to the WLAN card. The following table provides the antenna-cable color scheme for the WLAN card supported by the Embedded Box PC. Connectors on the WLAN card Antenna-cable color Main (white triangle) White and gray Auxiliary (black triangle) Black and gray 1 tab 2 mPCIE2 slot 3 notch 4 WLAN card 5 WLAN-card bracket 6 M2x3 screws (2) 7 WLAN-antenna cables (2) Post-requisites Replace the back cover.
Removing the WWAN card WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites Remove the back cover.
3 46 Remove the WWAN card from the mPCIE1 slot.
Replacing the WWAN card WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance.
5 Replace the screws that secure the WWAN card to the system board. 1 WWAN card 2 notch 3 tab 4 M2x3 screws (2) 5 antenna cables Post-requisites Replace the back cover.
Removing the CANbus cable WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites Remove the back cover.
3 4 50 Remove the hexagonal screws that secure the CANbus cable to the I/O plate. 1 CANbus cable 2 CANbus connector 3 CANbus card 4 intrusion-switch cable 5 cable-routing guide 6 IET board 7 4-40UNCx6.3 screws (2) 8 I/O plate Remove the CANbus cable from the Embedded Box PC.
Replacing the CANbus cable WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1 Insert the CANbus port into the CANbus slot on the I/O plate.
3 4 52 Route the CANbus cable above the intrusion-switch cable. 1 CANbus cable 2 CANbus connector 3 CANbus card 4 intrusion-switch cable 5 cable-routing guide 6 IET board 7 4-40UNCx6.3 screws (2) 8 I/O plate Slide the CANbus cable to the connector on the CANbus card.
Post-requisites Replace the back cover.
Removing the CANbus card WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites Remove the back cover.
3 Remove the CANbus card from the mPCIE1 slot.
Replacing the CANbus card WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance.
4 Replace the screws that secure the CANbus card to the system board. 1 CANbus card 2 mPCIE1 slot 3 tab 4 notch 5 M2x3 screws (2) Post-requisites Replace the back cover.
Removing the intrusion switch WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites Remove the back cover.
2 3 Remove the screw that secures the intrusion-switch bracket to the chassis. 1 intrusion-switch cable 2 intrusion-switch connector 3 M3x5 countersunk screw 4 intrusion switch 5 chassis Remove the intrusion switch from the Embedded Box PC.
Replacing the intrusion switch WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance.
Removing the I/O plate WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites Remove the back cover.
2 Remove the hexagonal screws that secure the VGA port, Multi-Function port, and the COM ports to the I/O plate. 3 Remove the screws that secure the I/O plate to the chassis. 1 chassis 2 M3x5 countersunk screws (5) 3 4-40UNCx6.3 screws (8) 4 I/O plate NOTE: Ensure that you have removed the remote power-switch connector from the I/O plate.
4 Remove the I/O plate away from the chassis.
Replacing the I/O plate WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance.
Removing the WLAN-antenna connectors WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1 Remove the back cover. 2 Remove the I/O plate.
3 66 Remove the WLAN-antenna cable from the chassis.
Replacing the WLAN-antenna connectors WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance.
3 Connect the WLAN-antenna cables to the WLAN card. The following table provides the antenna-cable color scheme for the WLAN card supported by the Embedded Box PC. Connectors on the WLAN card Antenna-cable color Main (white triangle) White and gray Auxiliary (black triangle) Black and gray 1 WLAN antennas (2) 2 WLAN-antenna connectors (2) 3 I/O plate 4 WWAN-antenna connectors (2) 5 chassis Post-requisites 1 Remove the I/O plate. 2 Replace the back cover.
Removing the WWAN-antenna connectors WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1 Remove the back cover. 2 Remove the I/O plate.
3 70 Remove the WWAN-antenna connectors from the Embedded Box PC.
Replacing the WWAN-antenna connectors WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance.
2 3 Route the WWAN-antenna cables along the cable-routing guide on the IET board. 1 WWAN card 2 WWAN-antenna cables (2) 3 IET board 4 cable-routing guide 5 WLAN-antenna connectors (2) Connect the WWAN-antenna cables to the WWAN card. The following table provides the antenna-cable color scheme for the WWAN card supported by the Embedded Box PC.
2 Replace the back cover.
Removing the IET board WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1 Remove the back cover. 2 Remove the I/O plate.
Procedure 1 2 Remove the intrusion-switch cable from the intrusion-switch connector on the IET board. 1 nuts (5) 2 washers (5) 3 intrusion-switch cable 4 intrusion-switch connector 5 IET board Remove the screws that secure the IET board to the system board.
3 Remove the IET board from the IET-board connector from the side where the memory-module is located.
Replacing the IET board WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1 Push the IET board into the IET-board connector.
Removing the top cover WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1 Remove the back cover.
3 Remove the top cover away the chassis.
Replacing the top cover WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1 Place the top cover into the chassis.
Removing the coin-cell battery WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance.
2 82 Remove the coin-cell battery from its socket.
Replacing the coin-cell battery WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance.
Removing the system board WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. NOTE: Your Embedded Box PC’s Service Tag is stored in the system board.
2 Remove the system board from the chassis. 1 STDF (L20) HEX, M2.
3 Remove the thermal pads from the chassis.
Replacing the system board WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. NOTE: Your Embedded Box PC’s Service Tag is stored in the system board.
11 Replace the back cover. Entering the Service Tag in the BIOS setup program 1 Turn on or restart the Embedded Box PC. 2 Press F2 when the Dell logo is displayed to enter the BIOS setup program. 3 Navigate to the Main tab and enter the Service Tag in the Service Tag Input field.
Removing the Dell logo board WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1 Remove the back cover.
Procedure 1 Remove the screws that secure the Dell logo board to the chassis.
2 Remove the Dell logo board from the chassis.
Replacing the Dell logo board WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1 Place the Dell logo board into the chassis.
BIOS setup program Entering BIOS setup program Before turning on the Embedded Box PC, connect the keyboard, mouse, and monitor to the Embedded Box PC, or connect the Embedded Box PC through the KVM session or use Dell Wyse Cloud Client Manager (CCM) or Dell Command | Monitor (DCM) to update the BIOS configuration. 1 Turn on (or restart) the Embedded Box PC. 2 During POST, when the DELL logo is displayed, watch for the F2 prompt to appear, and then press F2 immediately.
5 6 Remove the jumper plug from pins 2 and 3 and replace it back on pins 1 and 2. 1 jumper plug 2 pin 1 3 pin 2 4 pin 3 Replace the IET board and back cover. Clearing forgotten passwords WARNING: Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC.
NOTE: The computer must be disconnected from the electrical outlet to clear the password setting. 1 Remove the back cover. 2 Locate the password reset jumper (PWD) on the system board. See “System-board components”. 3 Remove the jumper plug. 4 Wait for approximately five seconds to clear the password setting. 5 Turn on the Embedded Box PC. A message appears on your computer, indicating that the passwords are cleared. 6 Turn off the Embedded Box PC. 7 Replace the jumper plug.
Technology and components Power The Dell Embedded Box PC is shipped with the 12-26V DC power adapter. Processor The Dell Embedded Box PC is shipped with Intel Atom E3825, Intel Atom E3827, and Intel Atom E3845 processor. Mechanical The Embedded Box PC is optimized for fanless design, and easy wall/panel and DIN Rail Mount use. It provides easy access to connectors and switches. The Embedded Box PC also supports Dell branded and Unbranded OEM ready front cover badge versions.
Feature Description • Environmental Mounting Non-operating (storage): 5% to 95% (non-condensing) Base device: Dust-resistant IP30 • • • Wall-mount bracket DIN Rail options Mechanism for securing system on DIN rail Peripherals The following peripherals are available in the Embedded Box PC: • Wall-mount bracket • DIN rail • Power connector kit • Multi-Function port • Mobile Broadband card • Mobile WLAN card • CANbus card • Power adapter WLAN/WWAN The following WLAN and WWAN cards are opt
CANbus The CANBus daughter card is an optional accessory for Embedded Box PC.
