Administrator Guide
7. To configure a default gateway address, type the default gateway address you want to use (for example,
10.10.20.10), and press <Enter>.
8. To configure a DNS Suffix, type the DNS suffix you want to use (for example, storage.local), and press <Enter>.
9. To configure a primary DNS server IP address, type an IP address you want to use for the primary DNS server (for
example, 10.10.10.10), and press
<Enter>.
10. (Optional) To configure a secondary DNS server IP address, type y (for yes), and press <Enter>.
If you responded yes, type an IP address you want to use for the secondary DNS server (for example, 10.10.10.11),
and press <Enter>.
11. To change the default host name (for example, the serial number of the DR Series hardware appliance), type y (for
yes) and press <Enter>.
If you responded yes, type the host name you want to use, and press <Enter>. After you configure your host name
response, the current system settings are displayed.
12. To accept these settings, type y (for yes), and press <Enter>.
13. If you want to change any of these settings, type n (for no), and press <Enter>. Modify the settings as needed, and
press <Enter>.
When completed, a successful initialization message is displayed.
14. At the prompt, type exit and press <Enter> to end the DR Series system CLI session.
You are now ready to log in to the system using the DR Series system GUI.
노트: Before you log into the system using the DR Series system GUI, make sure to register it in the local Domain
Name System (DNS) for your network so that it is a DNS-resolvable entry.
노트: At this point, you could modify the bonding mode to use 802.3ad, if this configuration is available in your
network.
RACADM을 사용하여 iDRAC6/iDRAC7에 액세스
SSH 기반 또는 Telnet 기반 인터페이스를 통해 RACADM 유틸리티를 사용하여 iDRAC6/iDRAC7에 액세스할 수 있
습니다. RACADM(원격 액세스 컨트롤러 관리)은 Dell의 명령행 유틸리티로서 대역외 관리 기능을 제공하도록
iDRAC(integrated Dell Remote Access Control) 인터페이스 카드를 설정하고 구성할 수 있습니다.
iDRAC 카드에는 고유한 프로세서, 메모리, 네트워크 연결 및 시스템 버스에 대한 액세스의 컨트롤러가 포함되어
있습니다. 이를 통해 시스템 또는 네트워크 관리자는 로컬 콘솔에서 지원되는 웹 브라우저 또는 명령행 인터페
이스를 사용하여 전원 관리, 가상 매체 액세스 및 원격 콘솔 기능으로 시스템을 구성할 수 있습니다.
iDRAC 구성에 사용할 수 있는 로그인 값은 다음과 같습니다.
• 기본 사용자 이름: root
• 기본 암호: calvin
• 기본 정적 IP 주소: 192.168.0.120
자세한 내용은 support.dell.com/manuals에서
iDRAC용 RACADM 참조 안내서
,
iDRAC6(Integrated Dell Remote
Access Controller 6) 사용 설명서
또는
iDRAC7(Integrated Dell Remote Access Controller 7) 사용 설명서
를 참조하십
시오.
Logging in Using a Web Interface
To log in to the DR Series system using a browser-based connection, complete the following:
39