Administrator Guide
Table Of Contents
- Dell DR Series System Administrator Guide
- DR Series システムの概要
- Understanding the DR Series System
- About the DR Series System
- ドライブ容量と使用可能な物理容量
- Data Storage Terminology and Concepts
- Supported File System Protocols
- OpenStorage Technology (OST): DR Series System
- Rapid Data Storage (RDS): DR Series System
- DR Series System and Data Operations
- Supported Software and Hardware
- DR Series — Expansion Shelf Cabling
- DR Series システム拡張シェルフの追加
- Setting Up the DR Series System
- Interacting With the DR Series System
- Connections for Initializing a DR Series System
- DR Series システムの初期化
- RACADM を使用した iDRAC6/iDRAC7 へのアクセス
- Logging in Using a Web Interface
- Dashboard（ダッシュボード）ページとオプション
- Storage（ストレージ）ページとオプション
- About the Schedules Page and Options
- About the System Configuration Page and Options
- Support（サポート）ページとオプション
- Configuring the DR Series System Settings
- Managing DR Series Storage Operations
- DR Series システムの監視
- DR Series システムのサポートオプションの使用
- OST の設定と使用
- OST の理解
- OpenStorage Technology（OST）API
- OST ガイドライン
- OST Terminology
- Supported OST Software and Components
- OST Required Configurations
- ベストプラクティス：OST と DR Series システム
- クライアント側の最適化の設定
- Configuring an LSU
- Installing the Dell OST Plug-In
- NetBackup を使用した DR Series システム情報の設定
- Backing Up Data From a DR Series System (NetBackup)
- Using Backup Exec With a DR Series System (Windows)
- OST Plug-In and Supported Versions
- Installation Prerequisites for the OST Plug-In for Backup Exec
- Backup Exec GUI を使用した DR Series システムの設定
- Backup Exec を使用した DR Series システム上でのバックアップの作成
- Optimizing Duplication Between DR Series Systems Using Backup Exec
- Restoring Data from a DR Series System Using Backup Exec
- Understanding the OST CLI Commands
- Understanding OST Plug-In Diagnostic Logs
- Linux ユーティリティを使用した診断の収集
- メディアサーバー情報の収集に関するガイドライン
- Configuring and Using Rapid Data Storage
- RDS Overview
- RDS Guidelines
- Best Practices: RDS and the DR Series System
- Setting Client-Side Optimization
- Adding RDS Devices in NVBU
- Removing RDS Devices From NVBU
- Backing Up Data on the RDS Container Using NVBU
- Replicating Data to an RDS Container Using NVBU
- Restoring Data From a DR Series System Using NVBU
- Supported DR Series System CLI Commands for RDS
- Troubleshooting and Maintenance
- Supported Ports in a DR Series System
- 困ったときは
– Slave Interfaces
• Eth0
– MAC
– Maximum Speed
– Speed
– Duplex
• Eth1
– MAC
– Maximum Speed
– Speed
– Duplex
To configure new networking settings (or to change from those set using the Initial System Configuration Wizard),
complete the following:
1. Select System Configuration → Networking.
The Networking page is displayed. Select settings for hostname, IP Address, DNS, Bonding, or to view the Ethernet
port settings (Eth0-Eth3) for the DR Series system.
– To configure hostname, skip to step 2.
– To configure IP addressing, skip to step 5.
– To configure DNS, skip to step 10.
2. To change the current Hostname, select the Hostname tab and click Edit Hostname on the options bar.
The Edit Hostname dialog is displayed.
3. Type a hostname in Hostname that meets the following supported character types and length:
– Alphabetic—allows A-Z, a-z, or a combination of upper and lower case alphabetic characters.
– Numeric—allows numerals zero (0) through 9.
– Special characters—allows only the dash (-) character.
– Length limit—hostnames cannot exceed the maximum length of 19 characters.
4. Click Submit to set the new hostname for your system.
5. To change the current IP address settings for the selecte NIC bond or Ehternet port, select the Interfaces tab and
click Edit Interfaces on the options bar.
The Edit Interface — <bond or Ethernet port number> dialog is displayed.
6. Under IP Address, in Mode, select Static (to set static IP addressing for your system), or select DHCP (to set
dynamic IP addressing for your system).
メモ: To select the DHCP mode of IP addressing, select DHCP, and click Submit. The remaining substeps in
this step only need to be completed if you selected the Static mode of IP addressing for the DR Series system.
a) In New IP Address, type an IP address that represents the new IP address for your system.
b) In Netmask, type an netmask address value that represents your system (the system IP address and netmask
identify the network to which your system belongs).
c) In Gateway, type an IP address for the gateway associated with your system.
7. Under MTU, in MTU, enter the value you want to set as the maximum.
メモ: Ensure that the value that you enter in MTU is the same for the clients, Ethernet Switch, and the
appliance. The connection between the clients, the Ethernet switches, and the appliance will break if the
MTU number is not the same on all the components.
74