Reference Guide
Table Of Contents
- Dell Command | PowerShell Provider Version 2.3 Reference Guide
- Introduction to Dell Command | PowerShell Provider 2.3
- Attributes supported in Dell Command | PowerShell Provider 2.3
- AdvancedBootOptions
- AdvancedConfigurations
- BatteryInformation
- BIOSSetupAdvancedMode
- BootSequence
- IntelSoftwareGuardExtensions
- Manageability
- Maintenance
- MemoryInformation
- MiscellaneousDevices
- Passwords
- Performance
- POSTBehavior
- PowerManagement
- PreEnabled
- ProcessorInformation
- SecureBoot
- Security
- StealthModeControl
- SupportAssistSystemResolution
- SystemConfiguration
- SystemInformation
- SystemLogs
- ThermalConfiguration
- TPMSecurity
- USBConfiguration
- Video
- VirtualizationSupport
- Wireless
- Error reporting in Dell Command | PowerShell Provider 2.3
- Accessing documents from the Dell EMC support site
Table 15. PowerManagement (continued)
Attribute Name Description
Possible values:
● 7.5W
● 15W
UsbWake
Enables USB devices to wake the system from Standby.
NOTE: This feature is functional only when the AC power adapter is connected.
Possible values:
● Enabled
● Disabled
WakeOnAc
Controls the system's behavior when AC power is restored after AC power was lost.
Possible values:
● Disabled — System stays off after AC power is restored.
● Enabled — System powers on after AC power is restored.
WakeOnDock
Enables or disables waking the system when a docking connection is made.
Possible values:
● Enabled
● Disabled
WakeOnLan
Configures the wake-on-LAN feature.
Possible values:
● LanOnly — The system wake-on-LAN feature is enabled; either an onboard or an add-in
NIC can wake the system up.
● Disabled — Does not allow the system to power on when it receives a wakeup signal
from the LAN or wireless LAN.
● AddInCard — Enables NICs, plugged into the power connector, as the source of any
wake-on-LAN signal.
● WlanOnly — Allows the system to be powered on by special WLAN signal.
● LanWlan — Allows the system to be powered on by special LAN or wireless LAN signal.
● AddInCard — Allows the system to be powered on by NICs plugged into the special
power connector.
● Onboard — Allows the system to be powered on by Onboard NIC.
● LanWithPxeBoot — Enables the network controller and wakes up the system to boot
the PXE when a wake packet is sent to the system in the S4 or S5 state.
● SfpNic — Allows the system to wake-up by certain SFP signals.
● LanOrSfpNic — Allows the system to wake-up either by LAN, or by SFP signals.
● SfpNicWithPxeBoot — Allows the system to wake-up by SFP signals, and immediately
boot to PXE.
WakeOnLan2
Defines the wake-on-LAN2 feature.
● LanOnly — The system wake-on-LAN feature is enabled; either an onboard or an add-
in NIC can wake up the system.
● Disabled — The system does not respond to magic packets or other means of wake-
on-LAN. The NIC chip section that looks for packets will not be powered.
● LanWithPxeBoot — Enables the network controller and causes the system to wake up
and immediately boot to PXE when a wake packet is sent to the system in the S4 or S5
state.
WlanAutoSense
Enables or disables the WLAN radio when the system is connected to a wired network.
When disconnected from the wired network, WLAN radio is re-enabled.
Possible values:
Attributes supported in Dell Command | PowerShell Provider 2.3 27