Reference Guide
Table Of Contents
- Dell Command | PowerShell Provider Version 2.4 Reference Guide
- Introduction to Dell Command | PowerShell Provider 2.4
- Attributes supported in Dell Command | PowerShell Provider 2.4
- AdvancedBootOptions
- AdvancedConfigurations
- BatteryInformation
- BIOSSetupAdvancedMode
- BootSequence
- Connection
- Integrated Devices
- IntelSoftwareGuardExtensions
- Keyboard
- Manageability
- Maintenance
- MemoryInformation
- MiscellaneousDevices
- Passwords
- Performance
- POSTBehavior
- PowerManagement
- PreEnabled
- ProcessorInformation
- SecureBoot
- Security
- StealthModeControl
- SupportAssistSystemResolution
- SystemConfiguration
- SystemInformation
- SystemLogs
- ThermalConfiguration
- TPMSecurity
- USBConfiguration
- Video
- VirtualizationSupport
- Wireless
- Error reporting in Dell Command | PowerShell Provider 2.4
- Accessing documents from the Dell EMC support site
Table 22. Security (continued)
Attribute Name Description
Computrace This feature allows the users to enable or disable Absolute Software's Computrace
security software BIOS ROM. After this token is written, the state is permanently
maintained (this is a write-once field). This token is for Factory use only. Application
and management software must ignore this token. Write-once permanent is different
from write-once. Write-once is reset on a power cycle and/or chipset reset. Write-
once permanent cannot be reset or change once it is set. The following are the
possible values:
● Disable
● Activate
NOTE: You cannot enable or disable this feature using Dell Command | Configure.
CpuXdSupport Enables or disables the run disable mode of the processor. The operating system can
use this feature to hinder software that exploits buffer overflows. The following are
the possible values:
● Enabled
● Disabled
DisPwdJumper DisPwdJumper controls the physical password clear jumper on the motherboard. The
following are the possible values: Enabled—When this option is not selected, the
password jumper on the motherboard is activated to clear the BIOS admin and the
user passwords. Disabled—When this option is selected, the password jumper is
disabled, and the BIOS passwords are not cleared.
GeneralPurposeEncryption Enables or disables general-purpose encryption. The following are the possible values:
● Enabled
● Disabled
HDDInfo Displays the details of each HDD. The following information is displayed:
● HDDName—The name of the HDD.
● Present—Whether the HDD is physically present.
● PwdProtected—Whether a password exists for the HDD.
● PendingRestart—Whether a reboot is pending to set the password.
● AdminOnlyChange—Whether the changes to the password can be made only by
an administrator.
● SecureEraseSupported—Whether HDD Secure Erase is supported.
● SecureEraseEnabled—Whether HDD Secure Erase is enabled.
The following are the possible values: Read-only.
HDDPassword Sets, changes, or clears the HDD password. Enter the HDD password, if set, when
the system is powered on.
NOTE: After setting the HDD password, restart the system.
Possible values: String containing minimum 1 and maximum 32 characters including
whitespace.
HddProtection Lets the user choose loading of HDD Protection OPROM.
IntlPlatformTrust Enables or disables IntlPlatformTrust feature. The following are the possible values:
● Enabled—Displays the Intel Platform Trust Technology (PTT) device from the
operating system on the next boot.
● Disabled—Hides the Intel Platform Trust Technology (PTT) device from the
operating system on the next boot.
NOTE: When disabled, the PTT device is not displayed to the operating system,
and no changes can be made to the PTT device or its content.
IntelTME Controls the total memory encryption (TME) feature. The following are the possible
values:
● Enabled
● Disabled
30 Attributes supported in Dell Command | PowerShell Provider 2.4