Dell Command | PowerShell Provider Version 2.
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents 1 Introduction to Dell Command | PowerShell Provider 2.3................................................................. 4 2 Attributes supported in Dell Command | PowerShell Provider 2.3.....................................................5 AdvancedBootOptions..........................................................................................................................................................6 AdvancedConfigurations...............................................................
1 Introduction to Dell Command | PowerShell Provider 2.3 Dell Command | PowerShell Provider is a module that makes BIOS configuration easily manageable through the Windows PowerShell interface. It works for local and remote systems, and in a Windows Preinstallation Environment (WinPE). This document describes the supported attributes, and error reporting in Dell Command | PowerShell Provider.
2 Attributes supported in Dell Command | PowerShell Provider 2.3 The following are categories in Dell Command PowerShell Provider and contains BIOS attributes. Table 1. Attributes supported in Dell Command | PowerShell Provider Category Name Description AdvancedBootOptions Displays the attributes to configure advanced boot settings. AdvancedConfigurations Displays the attributes to configure various advanced settings.
Category Name Description Wireless Displays the attributes to configure wireless devices.
Attribute Name Description • AlwaysExceptInternalHdd — All UEFI boot paths require the user to enter the Admin password, except for the boot paths that are hosted on an internal hard disk drives. Always — Booting from any UEFI boot path requires the user to enter the Admin password. Never — The Admin password is not required for booting from UEFI boot paths. AlwaysExceptInternalHddPxe — All UEFI boot paths require the Admin password, except for boot paths hosted on internal hard disk drives or PXE Boot.
Attribute Name Description Possible values: • • Uefi — Enables booting to Unified Extensible Firmware Interface (UEFI) capable operating systems. Legacy — (the default) Ensures compatibility with operating systems that do not support UEFI. NOTE: Legacy boot mode is not allowed when secure boot is enabled or legacy option ROM is disabled. BootSequence Specifies the order in which a system searches for devices when trying to find an operating system to boot.
Manageability Table 8. Manageability Attribute Description AmtCap Set the intel active management technology (AMT) capability. Possible Values: • • • PostMebxKey Enabled - If Intel Active Management Technology is enabled, MEBx is available through the F12 menu and you can provision AMT. MEBx may not be not accessible if OROM Keyboard Access is disabled. Disabled - If Intel Active Management Technology is disabled, MEBx is not available in pre-boot.
Attribute Name Description • • Enabled — BIOS checks the BIOS image integrity during every booting process. Disabled — BIOS checks the BIOS image integrity only if the previous booting process did not complete. NOTE: BIOS checks the BIOS image integrity only if the BiosAutoRcvr option is enabled. BiosRcvrFrmHdd Enables or disables the system BIOS Recovery option.
MiscellaneousDevices Table 11. MiscellaneousDevices Attribute Name Description BroadComTruManage Enables or disables Broadcom TruManage technology. Possible values: • • Camera Enabled Disabled Enables or disables the camera. Possible values: • • Camera2 Enabled Disabled Enable or disables the backward-facing camera. Possible values: • • DediGPSRadio Enabled Disabled Enables or disables the internal GPS radio.
Attribute Name Description MiniCardSSDDevice Enables or disables the mini card Solid State Drive (SSD) module. Possible values: • • ModuleBayDevice Enabled Disabled Enables or disables the module bay. The module bay is a hot-pluggable bay where storage and media devices such as HDDs, CDs or DVDs can be installed. Possible values: • • OnboardModem Enabled Disabled Enables or disables the onboard internal modem. Possible values: • • PcCard Enabled Disabled Enables or disables the PC card.
Passwords Table 12. Passwords Attribute Name Description NOTE: If the criteria PwdMinLen >=8, PwdLowerCaseRqd=Enabled, and PwdUpperCaseRqd=Enabled is followed, then StrongPassword is Enabled. If this criteria is not followed, then StrongPassword is Disabled. Vice-versa is also applicable. PwdMinLen This feature controls the minimum number of characters that are mandatory for a password. Possible values: 4 - 32 PwdLowerCaseRqd This feature reinforces that the password must contain one lower case letter.
Attribute Name Description CPUCore This field specifies whether the processor has one or more cores enabled. The performance of some applications improve with additional cores. Possible values: • • • • • • • • • • • • • • • • • • • • • • • • • • • • • CpuSnoopMode CoresAll— All cores are enabled. Cores1 — Only one core is enabled. Cores2 — Two cores are enabled. Cores3 — Three cores are enabled. Cores4 — Four cores are enabled. Cores5 — Five cores are enabled. Cores6 — Six cores are enabled.
Attribute Name Description Possible values: • • DynTunML Enabled Disabled Enables operating system capability to enhance dynamic power tuning capabilities based on detected workloads. Protections for exposure: The –Admin password restricts editing the command –Removed in case when you are using command line interface. Possible values: • • EnableMultiCoreSupport Enabled Disabled Enables or disables multiple CPU cores.
Attribute Name Description IrstTimer Sets the Intel Rapid Start Timer. The value can be specified in minutes ranging from 0 to 999. Specify the Rapid Start timer value as 0 to put the system into a low-power state immediately after the system transition to a sleep mode. Possible values: Integer ranging from 0 to 999 LimitCpuidValue Restricts the maximum CPUID functions supported by the processor.
Attribute Name Description • • AmdCpuCore Disabled — Does not allow the TurboBoost driver to increase the performance state of the processor preceding the standard performance. Enabled — Allows the Intel Turbo driver to increase the performance of the CPU or graphics processor. This field specifies whether the processor has one or more cores enabled.
Attribute Name Description • • ExternalHotKey Enabled Disabled Enables or disables Fn key emulation. Possible values: • • ExtPostTime Enabled—The Scroll Lock key on external keyboards emulate the Fn key only when running in a non-ACPI operating system. Disabled—The Scroll Lock key behaves normally. Creates an extra preboot delay for specified seconds to allow the user to see POST status messages. Possible values: • • • Fastboot 0s—Does not delay. 5s—Delays for 5 seconds. 10s—Delays for 10 seconds.
Attribute Name Description Possible values: • • • NumLock SystemUnique IntegratedNic1 Disabled Enables or disables the NumLock function when the system boots. Possible values: • • NumLockLed Enabled Disabled Enables or disables the NumLockLed function when the system boots. Possible values: • • PntDevice Enabled Disabled Defines how the system handles mouse and touchpad input. Possible values: • • • • PostF12Key SerialMouse—Uses a serial mouse and disables the internal touchpad.
Attribute Name Description Possible values: • • SignOfLifeByDisplay Enabled Disabled This option allows the system to indicate that the power button has been pressed during POST by displaying the Dell Logo. Possible values: • • SignOfLifeByAudio Enabled Disabled This option allows the system to indicate that the power button has been pressed during POST with an audible tone.
PowerManagement Table 15. PowerManagement Attribute Name Description AcPwrRcvry Controls the system's behavior when AC power is restored after AC power has been lost. Possible values: • • • Off — System stays off after AC power is restored. On — System powers on after AC power is restored. Last — System returns to the previous state after AC power recovery. AdvancedBatteryChargeConfigu Configures the days settings based on BeginningOfDay and workperiod.
Attribute Name Description • • AutoOnTue Enabled Disabled Enables or disables the AutoOn functionality at the specified time on Tuesdays. Possible values: • • AutoOnWed Enabled Disabled Enables or disables the AutoOn functionality at the specified time on Wednesdays Possible values: • • AutoOnThur Enabled Disabled Enables or disables the AutoOn functionality at the specified time on Thursdays.
Attribute Name Description • • CustomChargeStart Enabled Disabled Sets the percentage value ranging from 50 to 95 at which custom battery charging should start. NOTE: Primary Battery Custom Charge Start percent must be less than the Primary Battery Custom Charge End percent and the minimum difference between the two must be 5 percent. Possible values: Integers ranging from 50 to 95 CustomChargeStop Sets the percentage value ranging from 55 to 100 at which the custom battery charging should stop.
Attribute Name Description FanSpeedLvl Configures the fan speed control if the fan speed is set to Auto using FanSpeed attribute. 0 sets the fan speed to the optimal speed level, and a higher percentage provides enhanced cooling. Possible values: Integers ranging from 0 to 100 IntelReadyModeEn This option enables or disables Intel Ready Mode Technology (iRMT).
Attribute Name Description • • PowerUsageMode Enabled - If the feature is set to enabled, the system powers up from the off state whenever the lid is opened. This system powers on when powered either by the AC adapter or the system battery. Disabled - If the feature is set to disabled, the system does not power up from the off state whenever the lid is opened. Sets the system power usage modes.
Attribute Name Description • Speedshift Custom — Charges the battery in Express Charge mode using the express charging algorithm, Dell's fast charging technology. Enables or disables the Intel Speed Shift Technology support. Setting this option to Enabled allows the operating system to select the appropriate processor performance automatically. Possible values: • • TypeCPower Enabled Disabled Configures the maximum power for type-C connector. Possible values: • • UsbWake 7.
Attribute Name Description • • • WlanAutoSense LanOnly — The system wake-on-LAN feature is enabled; either an onboard or an add-in NIC can wake up the system. Disabled — The system does not respond to magic packets or other means of wake-on-LAN. The NIC chip section that looks for packets will not be powered. LanWithPxeBoot — Enables the network controller and causes the system to wake up and immediately boot to PXE when a wake packet is sent to the system in the S4 or S5 state.
Attribute Description • NOTE: Embedded Display Port (eDP) will be enabled by Integrated Graphics Processing Unit (iGPU). Disabled — The normal hybrid graphics mode is enabled. NOTE: This feature is used in hybrid graphics mode only. ExpansionBay 1 Enables or disables Expansion Bay 1. Possible values: • • ExpansionBay 2 Enabled Disabled Enables or disables Expansion Bay 2. Possible values: • • ExpansionBay 3 Enabled Disabled Enables or disables Expansion Bay 3.
Attribute Description • • • • • RecoveryTool Default OptimizeforThunderbolt Option1 Option2 Option3 Enables or disables the Dell recovery tool. Possible values: • • ReportLogoType Enabled — Enables the Dell recovery tool. Disabled — Disables the Dell recovery tool. Reports the type of splash screen logo (Dell or custom) that is passed from BIOS to user. Possible values: • RuggedDeskDockNicPxe 0 and 1 NOTE: You cannot enable or disable this feature using Dell Command | PowerShell Provider.
Attribute Name Description CurrentClockSpeed Displays the current speed of the processor. Possible values: Read-only HTCapable Specifies whether the system supports Hyper Threading (HT). Possible values: Read-only MaximumClockSpeed Displays the maximum speed supported by the processor. Possible values: Read-only ProcessorID Displays the processor ID that contains the processor-specific information that describes the features of the processor.
Attribute Name Description Possible values: • • • AdminPassword Enabled - If enabled, then the Absolute service is activated or deactivated. Disabled - If disabled, then the Absolute service does not run. PermanentlyDisabled - If the Absolute interface is permanently disabled, then the Absolute feature can be enabled by using the factory reset feature. Sets, changes, or clears the administrator (admin) password (also called the setup password).
Attribute Name Description reset on a power cycle and/or chipset reset. Write-once permanent cannot be reset or change once it is set. Possible values: • • Disable Activate NOTE: You cannot enable or disable this feature using Dell Command | Configure. CpuXdSupport Enables or disables the run disable mode of the processor. The operating system can use this feature to hinder software that exploits buffer overflows.
Attribute Name Description MasterPasswordLockout Enables or disables master password settings. CAUTION: Using the Dell Command | PowerShell Provider, you cannot disable this feature. Possible values: • Enabled — The master password cannot be used to: • • clear other passwords • unlock and access Hard Disk Drive • erase data from Hard Disk Drive. Disabled — The master password can be used to: • • • clear other passwords unlock and access Hard Disk Drive erase data from Hard Disk Drive.
Attribute Name Description Possible values: • • Enabled Disabled NOTE: You can disable SedBlockSidAuthentication in manufacturing mode or while setting up the BIOS Setup Administrator password. Smmsecuritymitigation Enables or disables the additional UEFI SMM Security Mitigation protections. The operating system uses this feature to protect the secure environment created by virtualization-based security. Enabling this feature provides the additional UEFI SMM Security Mitigation protections support.
Attribute Description Possible values: • • StealthModeFans Enabled Disabled Enables or disables Stealth Mode behavior for fans if the StealthMode attribute is enabled. Possible values: • • StealthModeGPSReceiver Enabled Disabled Enables or disables Stealth Mode behavior for GPS receiver if the StealthMode attribute is enabled. Possible values: • • StealthModeLCD Enabled Disabled Enables or disables Stealth Mode behavior for the LCD if the StealthMode attribute is enabled.
SupportAssistSystemResolution Table 21. Attribute Description AutoOSRecoveryThreshold Sets the threshold value for auto OS recovery. Possible values: 0 to 3 Controls the automatic boot flow for SupportAssist System Resolution console and for Dell OS Recovery Tool.
Attribute Name Description AnalogDigitalInterfaceModeChann Sets the defined Analog or Digital Interface mode for channel 2. el2 Possible values: • • • • • Unused—Channel is unused. ADCInput—Sets the channel mode as Analog-to-Digital Converter (ADC) input. DACOutput—Sets the channel mode as Digital-to-Analog Converter (DAC) output. DACAndADC—Sets the channel mode as DAC output, but can be monitored through ADC input. GPIO—Sets the channel mode as General Purpose Input or Output.
Attribute Name Description AnalogDigitalInterfaceModeChann Sets the defined Analog or Digital Interface mode for channel 8. el8 Possible values: • • • • • BatteryFuelGauge Unused — Channel is unused. ADCInput — Sets the channel mode as Analog-to-Digital Converter (ADC) input. DACOutput — Sets the channel mode as Digital-to-Analog Converter (DAC) output. DACAndADC — Sets the channel mode as DAC output, but can be monitored through ADC input. GPIO — Sets the channel mode as General Purpose Input or Output.
Attribute Name Description Possible values: • • DisWLANRadio Enabled Disabled WLAN radio stops functioning when stealth mode is enabled. Possible values: • • DisWWANRadio Enabled Disabled WWAN radio stops functioning when stealth mode is enabled. Possible values: • • DockSupportOnBattery Enabled Disabled Enabling DockSupportOnBattery allows you to use the docking station, when AC power is absent, but only when the battery is preceding a certain charge percentage.
Attribute Name Description • Emmcdevice Raid — SATA is configured to support RAID mode (Intel Rapid Restore Technology). Enables or disables the eMMC drive. Possible values: • • FrontBezelLEDIntensity Enabled Disabled Controls the light intensity of system's front bezel LED. Possible values: • • • • FrontFan Possible values: • • FingerprintReader Disabled Low Medium Full Enabled—When enabled, the front fan utilizes the thermal solution of the system.
Attribute Name Description Possible values: • • Hdd2FanEnable Enabled Disabled Enables or disables the automatic fan controller, an error check of a fan. If a fan is detected, this function is automatically enabled. Disabling the fan requires physical removal of the HDD2 fan. Possible values: • • Hdd3FanEnable Enabled Disabled Enables or disables the automatic fan controller, an error check of a fan. If a fan is detected, this function is automatically enabled.
Attribute Name Description IoModule Enables or disables I/O module. Possible values: • • IoModule 2 Enabled Disabled Enables or disables I/O module 2. Possible values: • • IoModule 3 Enabled Disabled Enables or disables I/O module 3. Possible values: • • IoModule 4 Enabled Disabled Enables or disables I/O module 4. Possible values: • • KbdBacklightTimeoutAc Enabled Disabled Configures the time-out value for the keyboard backlight when an AC adapter is plugged into the system.
Attribute Name Description • • • KeyboardBacklightCustom1Color Blue Custom1 Custom2 Configures the Custom1 color by specifying the RGB values by mentioning it in 'R:G:B' format. Each color component value ranges from 0 to 255. Possible values: [0-255]:[0-255]:[0-255] KeyboardBacklightCustom2Color Configures the Custom2 color by specifying the RGB values by mentioning it in 'R:G:B' format. Each color component value ranges from 0 to 255.
Attribute Name Description LiquidCooler2 Enables or disables the liquid cooler 2. Possible values: • • LptMode Enabled - Enables the liquid cooler 2. Disabled - Disables the liquid cooler 2. Determines how the parallel port on the docking station operates. Possible values: • • • • M2PcieSsd0 Disabled — Port is disabled. At — Port is configured for IBM AT compatibility. Ps2 — Port is configured for IBM PS2 compatibility. Ecp — Extended Capability Port protocol. Enables or disables M2 PCIE SSD 0.
Attribute Name Description • • Minisas1 Enabled Disabled Enables or disables the Minisas drive 1. Possible values: • • Minisas2 Enabled Disabled Enables or disables the Minisas drive 2. Possible values: • • Minisas3 Enabled Disabled Enables or disables the Minisas drive 3. Possible values: • • Nfc Enabled Disabled Enables or disables the Near Field Computing (Nfc) device.
Attribute Name Description • PcibusCount Large — Allocates a large region of memory to PCI memory mapped I/O. This reserves the large device-specific memory regions, but reduces the amount of usable memory in 32-bit operating system. Sets the maximum number of PCI bus counts for the system. Possible values: • • • PowerButton 64 128 256 Enables, disables, or partially disables the power button.
Attribute Name Description Sata6 Enables or disables the seventh SATA drive controller. Possible values: • • Sata7 Enabled Disabled Enables or disables the eighth SATA drive controller. Possible values: • • Sata8 Enabled Disabled Sets SATA port 8 to off or auto. Possible values: • • Serial1 Enabled Disabled Configures the first (or only) built-in serial port.
Attribute Name Description • • • • • Serial5 Disable RS232 RS422 RS485 Auto Configures the fifth (if available) built-in serial port. Possible values: • • Serial6 Disabled Auto Configures the sixth (if available) built-in serial port. Possible values: • • SignOfLifeByLogo Disabled Auto This option indicates that, during POST the power button has been pressed by displaying the customized logo.
Attribute Name Description TabletButtonsTimeoutAc This feature defines the illumination timeout value for the tablet buttons when an AC adapter is connected to the system. The buttons are illuminated when they are pressed, and remains illuminated for that specified timeout period. The tablet button illumination timeout value works when button illumination is enabled. If you select Never, the buttons remain illuminated whenever the system is connected to the AC adapter.
Attribute Name Description Possible values: • • UsbPowerShare Enabled — Pressing Fn+B will toggle light emissions from the system. Disabled — Pressing Fn+B keys has no effect and will not toggle light emissions from the system. Configures the USB PowerShare feature behavior. Possible values: • • Vmdnvmepcie0 Enabled — Charges the external devices, such as phones and laptop music players, using the stored system battery when the system is turned off or in sleep mode.
Attribute Name Description WlanRegionCode Sets the WLAN code for specific region. Possible values: • • • • • • • • rtw — (Rest of the World) Sets the WLAN region code for the rest of the world. This option is selected by default. na — (North America (FCC)) Sets the WLAN region code for Canada and the United States.
Attribute Name Description • • PowerLogClear Keep — Does not clear the system event log on the next boot. Clear — Clears the system event log on the next boot. Prevents or allows the power event log to be cleared on the next boot. Possible values: • • ThermalLogClear Keep — Does not clear the power event log on the next boot. Clear — Clears the power event log on the next boot. Prevents or allows the thermal event log to be cleared on the next boot.
Attribute Name Description PpibypassSedBlockSidCommand is disabled, BIOS does not require user input while sending the Block SID command. Possible values: • • SHA256 Disabled Enabled NOTE: You can enable PpibypassSedBlockSidCommand in manufacturing mode or while setting up the BIOS Setup Administrator password. Sets the hash algorithm used for TPM 2.0 measurements. Possible values: • • • • Disabled — Sets hash algorithm to SHA-1. Enabled — Sets hash algorithm to SHA-256.
Attribute Name Description TpmPpiPo Controls the physical presence requirement for the following operations: Enable, Activate, and SetOwnerInstall_True. Possible values: • • TpmSecurity Enabled — Physical presence is not required to perform any of these operations. Disabled — Physical presence is required to perform these operations. Controls whether the Trusted Platform Module (TPM) in the system is enabled and visible to the operating system.
Attribute Name Description • ThunderboltBoot Disabled Enables or disables booting from the Thunderbolt device. Possible values: • • ThunderboltPorts Enabled Disabled Enables or disables the thunderbolt ports controller in the system. Possible values: • • Thunderbolt Enabled Disabled Enables or disables the thunderbolt controller in the system. Possible values: • • ThunderboltPreboot Enabled Disabled Enables OROMs and preboot UEFI drivers that are provided by Thunderbolt devices or PCIe devices.
Attribute Name Description • • USBPort09 Enabled Disabled Enables or disables USB port 9. Possible values: • • USBPort12 Enabled Disabled Enables or disables USB port 12. Possible values: • • USBPort13 Enabled Disabled Enables or disables USB port 13. Possible values: • • USBPort14 Enabled Disabled Enables or disables USB port 14. Possible values: • • USBPort15 Enabled Disabled Enables or disables USB port 15.
Attribute Name Description • • USBPort25 Enabled Disabled Enables or disables USB port 25. Possible values: • • USBPort26 Enabled Disabled Enables or disables USB port 26. Possible values: • • USBPort27 Enabled Disabled Enables or disables USB port 27. Possible values: • • USBPort28 Enabled Disabled Enables or disables USB port 28. Possible values: • • USBPort29 Enabled Disabled Enables or disables USB port 29. Possible values: • • Usb30 Enabled Disabled Enables or disables USB 3.0.
Attribute Name Description Possible values: • • UsbPortsFront1 Enabled Disabled Enables or disables USB front port 1. Possible values: • • UsbPortsFront2 Enabled Disabled Enables or disables USB front port 2. Possible values: • • UsbPortsFront3 Enabled Disabled Enables or disables USB front port 3. Possible values: • • UsbPortsFront4 Enabled Disabled Enables or disables USB front port 4.
Attribute Name Description • • UsbPortsRear5 Enabled Disabled Enables or disables USB Ports Rear 5. Possible values: • • UsbPortsRear6 Enabled Disabled Enables or disables USB Ports Rear 6. Possible values: • • UsbPortsSide Enabled Disabled Enables or disables all side USB Ports in the system. Possible values: • • UsbPortsSide1 Enabled Disabled Enables or disables USB side port 1. Possible values: • • UsbPortsSide2 Enabled Disabled Enables or disables USB side port 2.
Video Table 28. Video Attribute Name Description AmbLightSen Enables or disables the ambient light sensor. Possible values: • • BootTimeVideo Enabled Disabled Sets the onboard or the first video controller for boot time messages. Possible values: • • Onboard — The onboard video controller is used for boot-time messages. Addin — The first add-in video controller is used for boot-time messages. NOTE: Depending on the BIOS search and system slot layout, the first add-in device changes.
Attribute Name Description • • • • • • • • • • • • • • • Slot2 — Sets the 3rd slot as the primary video device slot. Slot3 — Sets the 4th slot as the primary video device slot. Slot4 — Sets the 5th slot as the primary video device slot. Slot5 — Sets the 6th slot as the primary video device slot. Slot6 — Sets the 7th slot as the primary video device slot. Slot7 — Sets the 8th slot as the primary video device slot. Slot8 — Sets the 9th slot as the primary video device slot.
Attribute Description IntelVMDTechnology Enables or disables the Intel Volume Management Device (VMD) technology. Selecting Auto Enables VMD for any PCIe SSD connected to PCIe root ports. If the Auto option is not selected, then it disables VMD for all ports. SSD works only as native NVMe device. Possible values: • • VmdPcieSlot Auto Disabled Enables or disables the Intel Volume Management Device (VMD) technology Pcie slot. Selecting Auto Enables VMD for any PCIe SSD connected to PCIe root ports.
Attribute Name Description Ant A indicates dock antenna A, and Ant B indicates dock antenna B. NOTE: This setting applies to rugged docking stations and does not apply to USB Type-C docking stations. Possible values: • • • • • • • BluetoothDevice AllInternal WlanWwanExt WlanGpsExt WwanGpsExt WlanExt WwanExt GpsExt Enables or disables the internal Bluetooth device.
Attribute Name Description • WirelessSwitchUwb Disabled—Physical wireless On-Off switch cannot turn the WWAN On-Off. Determines that UWB (Ultra Wide Band) Radio will be controlled by the wireless On-Off switch. Possible values: • • WirelessSwitchWiGigCtrl Enabled—Physical wireless On-Off switch can turn the UWB Radio On-Off. Disabled—Physical wireless On-Off switch cannot turn the UWB Radio On-Off.
3 Error reporting in Dell Command | PowerShell Provider 2.3 Dell Command | PowerShell Provider provides an Error Reporting feature. Dell Command | PowerShell Provider uses the PowerShell ErrorVariable parameter to capture the ErrorRecord. This ErrorVariable can be used to get more information such as exception, error id, error category, and recommended action, and so on, about an error. NOTE: If the system does not have a WMI-ACPI compliant BIOS. Update the BIOS with a compatible version, if available.
Error Category Error ID Scenarios Example StringLengthNotInRange Doing set operation by giving string which has out of range length for an attribute which accepts a string having length within a range. si .\SystemInformation\Asset “thisismorethan10characters” InvalidTimeFormat Doing set operation by giving invalid time format. si .\PeakShiftDayConfiguration Sunday StartTime "34:34" InvalidPrimaryBatteryCustomCha Not keeping the minimum difference rgeDifference between CustomChargeStart and CustomC
Error Category Error ID Scenarios Example si .\SystemInformation\SvcTag sdwadnakjsd NewDriveNotSupported ObjectNotFound DellSmbiosPathNotFound If newly created drive name is not equal to DellSmbios, Path is correct but either attribute name or category name is wrong. Or Category does not have any supported attribute for local system and trying to get or set some attributes. dir .\PowerManagement\ gi .\PowerManagement\Numlck si .\PowerManagement\Numlck “enabled” si .\POSTBehaviord\Numlock “enabled” Op
4 Accessing documents from the Dell EMC support site You can access the required documents by selecting your product. 1. Go to www.dell.com/manuals. 2. Click Browse all products, click Software, and then click Client Systems Management. 3. To view the required documents, click the required product name and version number.
