Dell Command | Monitor Version 10.
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents 1 Introduction to Dell Command | Monitor 10.3.................................................................................. 4 Supported Windows operating systems............................................................................................................................. 4 Downloading Dell Command | Monitor...............................................................................................................................
1 Introduction to Dell Command | Monitor 10.3 This guide provides instructions on how to install Dell Command | Monitor on Dell enterprise client systems and on Dell IoT Gateway systems and Embedded PCs. For more information about supported systems, see Release notes available at dell.com/ dellclientcommandsuitemanuals. NOTE: Dell Command | Monitor was formerly Dell OpenManage Client Instrumentation (OMCI). After the OMCI version 8.2.1, OMCI is rebranded as Dell Command | Monitor.
2 System requirements for Dell Command | Monitor 10.3 This section provides information about the hardware requirements of Dell Command | Monitor. Hardware requirements • • Supported enterprise client system with SMBIOS 2.3 or later Supported systems that are compatible with WMI-ACPI compliant BIOS System requirements for Dell Command | Monitor 10.
3 Prerequisites for Dell Command | Monitor 10.3 Before installing Dell Command | Monitor, ensure that your system meets the following requirements. Topics: • • Prerequisites for systems running on Windows Prerequisites for systems running on Linux Prerequisites for systems running on Windows • • Systems must be compatible with a WMI-ACPI compliant BIOS. If a system does not have a WMI-ACPI compliant BIOS over which to install Dell Command | Monitor, update the BIOS with a compatible version.
parameters are not displayed on the EDM server portal until the EDM agent performs a next periodic check-in, or EDM is restarted. Prerequisites for Dell Command | Monitor 10.
4 Installing Dell Command | Monitor 10.3 for systems running on Windows You can install Dell Command | Monitor using one of the following methods: • • Using the Graphical User Interface, also known as the Dell Command | Monitor installation wizard Using Command Line Interface (CLI) for silent Installation NOTE: The Dell Command | Monitor installation file is available as a Dell Update Package (DUP) at dell.com/support. For more information, see Downloading Dell Command | Monitor.
3. Click Yes. The Update Package screen is displayed. 4. Click Install. The Welcome to the InstallShield Wizard for Dell Command | Monitor screen is displayed. 5. Click Next. The License Agreement screen is displayed. 6. Read the software license agreement, select I accept the terms in the license agreement, and then click Next. The Improvement Program Consent screen is displayed. 7.
• • • Standards-based Instrumentation — The Standards-based Instrumentation provides instrumentation available in the root/ DCIM/sysman. This namespace complies with the DMTF DASH standards. Enable SNMP — Enable SNMP supports Simple Network Management Protocol for client systems. Specify the installation directory. 7. Click Next. The Ready to Install the Program screen is displayed.
Operation Command Example and Comments Silent or unattended installation For 32-bit systems, type: msiexec /i Command_Monitor_x86.msi /qn For 32–bit Windows, use For 64-bit systems, type: msiexec /i Command_Monitor_x64.msi/qn For 64–bit Windows, use Silent or unattended installation with Standard Namespaces msiexec /i Command_Monitor_.
Operation Command Example and Comments see https://downloads.dell.com/ manuals/all-products/ esuprt_software_int/ esuprt_software_client_systems_ mgmt/command-monitorv102_reference-guide2_en-us.pdf 12 Installing Dell Command | Monitor 10.
5 Installing Dell Command | Monitor 10.3 for systems running on Linux You can install Dell Command | Monitor on a system running Linux using one of the following methods: • • • For systems running Ubuntu Desktop, see Installing Dell Command | Monitor using the Deb package. For systems running Red Hat Enterprise Linux (RHEL), see Installing Dell Command | Monitor using RPM package. For Dell Edge Gateway 5000/3000 series systems running Ubuntu Core 15.04, see Installing Dell Command | Monitor 9.1 or 9.1.
4. To verify that the driver module is loaded, run lsmod | grep dcdbas lsmod | grep dell_smbios NOTE: If the driver module is not available, a. Retrieve the driver details by running modinfo dcdbas modinfo dell_smbios b. Load the driver module by running modprobe dcdbas modprobe dell_smbios 5. To install Dell Command | Monitor, run dpkg -i command-monitor_-..deb 6. To verify that the Dell Command | Monitor is installed in your system, run.
Installing Dell Command | Monitor on the systems running Ubuntu Core 16 using Snap package To install Dell Command | Monitor on systems running Ubuntu Core 16 from the Dell Canonical store using snap package: 1. Log in to the Gateway system. The default username and password is admin 2. Run the following command: snap install .snap Installing Dell Command | Monitor 10.
6 Upgrading Dell Command | Monitor 10.3 for systems running on Windows You can upgrade Dell Command | Monitor on a system running Windows using one of the following methods: • • • Using DUP, see Upgrading Dell Command | Monitor using DUP Using MSI file, see Upgrading Dell Command | Monitor using the MSI file Using CLI, see Upgrading Dell Command | Monitor in CLI or silent mode NOTE: Only users with Administrator privileges can install, upgrade, or uninstall Dell Command | Monitor.
Upgrading Dell Command | Monitor in CLI or silent mode You can upgrade from the previous version of Dell Command | Monitor using CLI without restarting the system. Table 2. Commands used for upgrade Operation Command Upgrade from previous version (major upgrade) msiexec /i Command_Monitor_.msi REINSTALL=ALL REINSTALLMODE=vmous /qn To upgrade without reboot msiexec /i Command_Monitor_.
7 Upgrading Dell Command | Monitor 10.3 for systems running on Linux You can upgrade Dell Command | Monitor on a system running Linux using one of the following methods: • • • For systems running Ubuntu Desktop operating system, see Upgrading Dell Command | Monitor using Deb package.
2. Run the following command: snappy update dcm Upgrading Dell Command | Monitor 10.
8 Uninstalling Dell Command | Monitor 10.
Table 3. Commands for uninstallation Operation Command Remove Dell Command | Monitor using MSI msiexec /x Command_Monitor_.msi /qn Remove Dell Command | Monitor using upgrade code For 64–bit Windows operating systems, type: msiexec /x {91E79414-DB41-4030-9A13E133EE30F1D5} /qn Uninstalling Dell Command | Monitor 10.
9 Uninstalling Dell Command | Monitor 10.3 for systems running on Linux You can uninstall Dell Command | Monitor from a system running Linux using one of the following methods: • • • • For systems running Ubuntu Desktop, see Uninstalling Dell Command | Monitor using Deb Package For systems running Red Hat Enterprise Linux (RHEL), see Uninstalling Dell Command | Monitor using RPM Package For Dell Edge Gateway 5000/3000 series systems running Ubuntu Core 15.04, see Uninstalling Dell Command | Monitor 9.
1. To uninstall Dell Command | Monitor and remove configuration files and temporary files, run rpm –e command-monitor 2. To uninstall Hapi and remove configuration files and temporary files, run rpm –e srvadmin-hapi 3. To uninstall OMI and remove configuration files and temporary files, run rpm –e omi 4. To verify that Dell Command | Monitor is uninstalled in your system, run rpm -qa | grep command-monitor Uninstalling Dell Command | Monitor version 9.1 and 9.1.
