Users Guide
メモ: クライアント VT100 エミュレーションウィンドウの設定時、リダイレクトされたコンソールを表示
するウィンドウまたはアプリケーションを 25 行 x 80 列に設定し、テキストが正しく表示されるようにし
てください。この設定を行わないと、一部のテキスト画面が文字化けすることがあります。
/etc/grub.conf ファイルを次のように編集します。
1. ファイルの一般設定セクションを見つけ、次の 2 行を新たに追加します。
serial --unit=1 --speed=57600 terminal --timeout=10 serial
2. カーネル行に次の 2 つにオプションを追加します。
kernel console=ttyS1,57600
3. /etc/grub.conf に splashimage ディレクティブがある場合は、コメントアウトします。
次の例は、この手順で説明した変更を示しています。
# grub.conf generated by anaconda # # Note that you do not have to rerun
grub after making changes # to this file # NOTICE: You do not have a /boot
partition. This means that # all kernel and initrd paths are relative to /,
e.g. # root (hd0,0) # kernel /boot/vmlinuz-version ro root= /dev/sdal #
initrd /boot/initrd-version.img # #boot=/dev/sda default=0 timeout=10
#splashimage=(hd0,2)/grub/splash.xpm.gz
serial --unit=1 --speed=57600 terminal --timeout=10
serial
title Red Hat Linux Advanced Server (2.4.9-e.3smp) root (hd0,0) kernel /
boot/vmlinuz-2.4.9-e.3smp ro root= /dev/sda1 hda=ide-scsi console=ttyS0
console= ttyS1,57600 initrd /boot/initrd-2.4.9-e.3smp.img title Red Hat
Linux Advanced Server-up (2.4.9-e.3) root (hd0,00) kernel /boot/
vmlinuz-2.4.9-e.3 ro root=/dev/sda1 initrd /boot/initrd-2.4.9-e.3.img
/etc/grub.conf ファイルを編集するときは、次のガイドラインに従ってください。
– GRUB のグラフィカルインタフェースを無効にし、テキストベースのインタフェースを使用しま
す。テキストベースのインタフェースを使用しないと、GRUB 画面が RAC 仮想コンソールで表示
されません。グラフィカルインタフェースを無効にするには、splashimage で始まる行をコメ
ントアウトします。
– 複数の GRUB オプションを開始してシリアル接続経由でコンソールセッションを起動するには、
すべてのオプションに次の行を追加します。
console=ttyS1,57600
この例は、最初のオプションだけに console=ttyS1,57600 が追加されたことを示します。
起動後のサーバーシリアルコンソールリダイレクトのための Linux の設定
/etc/inittab ファイルを次のように編集します。
COM2 シリアルポートに agetty を設定するための新しい行を追加します。
co:2345:respawn:/sbin/agetty -h -L 57600 ttyS1 ansi
次の例は、新しい行が追加されたファイルを示しています。
# # inittab This file describes how the INIT process # should set up the system
in a certain # run-level. # # Author: Miquel van Smoorenburg # Modified for RHS
Linux by Marc Ewing and # Donnie Barnes # # Default runlevel. The runlevels
used by RHS are: # 0 - halt (Do NOT set initdefault to this) # 1 - Single user
mode # 2 - Multiuser, without NFS (The same as 3, if you # do not have
networking) # 3 - Full multiuser mode # 4 - unused # 5 - X11 # 6 - reboot (Do
NOT set initdefault to this) # id:3:initdefault: # System initialization.
si::sysinit:/etc/rc.d/rc.sysinit l0:0:wait:/etc/rc.d/rc 0 l1:1:wait:/etc/
rc.d/rc 1 l2:2:wait:/etc/rc.d/rc 2 l3:3:wait:/etc/rc.d/rc 3 l4:4:wait:/etc/
rc.d/rc 4 l5:5:wait:/etc/rc.d/rc 5 l6:6:wait:/etc/rc.d/rc 6 # Things to run in
every runlevel. ud::once:/sbin/update # Trap CTRL-ALT-DELETE ca::ctrlaltdel:/
sbin/shutdown -t3 -r now # When our UPS tells us power has failed, assume we
have a few # minutes of power left. Schedule a shutdown for 2 minutes from now.
# This does, of course, assume you have power installed and your # UPS is
159