Users Guide
A portion of this CD may contain open source software, which you can use under the terms and conditions of the specific license
under which the open source software is distributed.
THIS OPEN SOURCE SOFTWARE IS DISTRIBUTED IN THE HOPE THAT IT WILL BE USEFUL, BUT IS PROVIDED "AS IS"
WITHOUT ANY EXPRESSED OR IMPLIED WARRANTY; INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL DELL, THE COPYRIGHT HOLDERS, OR
THE CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTUTUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILTIY, WHETHER IN
CONTRACT, STRICT LIABITLY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILTIY OF SUCH DAMAGE.
U.S. GOVERNMENT RESTRICTED RIGHTS
The software and documentation are "commercial items" as that term is defined at 48 C.F.R. 2.101, consisting of "commercial
computer software" and "commercial computer software documentation" as such terms are used in 48 C.F.R. 12.212. Consistent
with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4, all U.S. Government end users acquire the software and
documentation with only those rights set forth herein.
Contractor/manufacturer is Dell Products, L.P., One Dell Way, Round Rock, Texas 78682.
GENERAL
This license is effective until terminated. It terminates upon the conditions set forth above or if you fail to comply with any of its
terms. Upon termination, you agree that the Software and accompanying materials, and all copies thereof, is destroyed. This
agreement is governed by the laws of the State of Texas. Each provision of this agreement is severable. If a provision is found to be
unenforceable, this finding does not affect the enforceability of the remaining provisions, terms, or conditions of this agreement.
This agreement is binding on successors and assigns. Dell agrees and you agree to waive, to the maximum extent permitted by law,
any right to a jury trial with respect to the Software or this agreement. Because this waiver may not be effective in some
jurisdictions, this waiver may not apply to you. You acknowledge that you have read this agreement, that you understand it, that you
agree to be bound by its terms, and that this is the complete and exclusive statement of the agreement between you and Dell
regarding the Software.
Viewing WWN/MAC address information
You can view the WWW/MAC address inventory of Network Adapters for each server slot or all servers in a chassis. The inventory
includes the following:
• Fabric Configuration
NOTE:
– Fabric A displays the type of the Input/Output fabric installed. If Fabric A is enabled, unpopulated slots display chassis-
assigned MAC addresses for Fabric A.
– iDRAC management controller is considered as part of Management Fabric and is shown along with rest of Fabrics.
– A check mark against the component indicates that the fabric is enabled for FlexAddress or FlexAddressPlus.
• Protocol that is being used on the NIC Adapter port. For example, LAN, iSCSI, FCoE, and so on.
• Fibre Channel World Wide Name (WWN) configuration and Media Access Control (MAC) addresses of a slot in the chassis.
• MAC address assignment type and the current active address type — Server assigned, FlexAddress, or I/O Identity MAC. A
green check mark indicates the active address type, either server-assigned, chassis-assigned, or remote assigned.
• Status of the NIC partitions for devices supporting partitioning.
You can view the WWN/MAC Address inventory using the Web interface or the RACADM CLI. Based on the interface, you can
filter the MAC address and know which WWN/MAC address is in use for that function or partition. If the adapter has NPAR
enabled, you can view which partitions are enabled or disabled.
Using the Web interface, you can view the WWN/MAC Addresses information for specific slots using the FlexAddress page (Click
Server Overview → Slot <x> → Setup → FlexAddress). You can view the WWN/MAC Addresses information for all the slots and
server using the
WWN/MAC Summary page (Click Server Overview → Properties → WWN/MAC). From both the pages you can
view the WWN/MAC Addresses information in the basic mode or the advanced mode:
121