Administrator Guide

7 Linecard not present
8 Linecard not present
9 Linecard not present
10 Linecard card problem C9000-RPM-2.56T C9000-RPM-2.56T 1-0(0-4854) -
11 Linecard not present
-- Route Processor Modules --
Slot Status NxtBoot Version
----------------------------------------------------------------
0 active online 1-0(0-4854)
1 not present
-- Power Supplies --
Unit Bay Status Type FanStatus FanSpeed(rpm) Power Usage (W)
---------------------------------------------------------------
0 0 absent
0 1 absent
0 2 absent
0 3 up AC up 3440 599.0
Total power: 599.0 W
-- Fan Status --
Unit Bay TrayStatus Fan0 Speed Fan1 Speed Fan2 Speed Fan3 Speed
---------------------------------------------------------------
0 0 up up 7943 up 7992 up 7975 up 8008
0 1 up up 7975 up 8008 up 7992 up 7975
0 2 up up 7959 up 7959 up 7959 up 7975
Speed in RPM
The following example runs offline diagnostics on a standalone switch
Dell#diag system
Warning - diagnostic execution will cause multiple link flaps on the peer side -
advisable to shut directly connected ports
Proceed with Diags [confirm yes/no]: yes
% Error: Invalid command - card is not present.
% Error: Invalid command - card must be offline.
% Error: Invalid command - card is not present.
% Error: Invalid command - card is not present.
% Error: Invalid command - card is not present.
% Error: Invalid command - card is not present.
% Error: Invalid command - card is not present.
% Error: Invalid command - card is not present.
% Error: Invalid command - card is not present.
Dell#Apr 26 22:32:01: %C9000LC0640:4 %DIAGAGT-6-DA_DIAG_STARTED: Starting diags on
linecard 4
2d3h3m : Approximate time to complete the Diags (all levels)... 10 Mins
Apr 26 22:32:01: %C9000LC0640:5 %DIAGAGT-6-DA_DIAG_STARTED: Starting diags on linecard 5
2d3h3m : Approximate time to complete the Diags (all levels)... 10 Mins
Apr 26 22:32:01: %C9000-RPM-2.56T:10 %DIAGAGT-6-DA_DIAG_STARTED: Starting diags on
linecard 10
2d3h3m : Approximate time to complete the Diags (all levels)... 10 Mins
Apr 26 22:32:01: %SYSTEM:LP %DIAGAGT-6-DA_DIAG_STARTED: Starting diags on CP unit
2d3h3m : Approximate time to complete the Diags (all levels)... 10 Mins
Apr 26 22:33:07: %RPM0-P:CP %IPC-2-STATUS: target line card 10 not responding
Apr 26 22:33:07: %RPM0-P:CP %CHMGR-2-LINECARD_DOWN: Major alarm: linecard 10 down - IPC
timeout
2d3h4m : Diagnostic test results are stored on file: flash:/TestReport-LP-5.txt
2d3h4m : Diagnostic test results are stored on file: flash:/TestReport-LP-4.txt
Apr 26 22:33:13: %C9000LC0640:5 %DIAGAGT-6-DA_DIAG_DONE: Diags finished on linecard 5
2d3h4m : Recommended to reboot the system after diagnostics!!!
Apr 26 22:33:14: %C9000LC0640:4 %DIAGAGT-6-DA_DIAG_DONE: Diags finished on linecard 4
2d3h4m : Recommended to reboot the system after diagnostics!!!
2d3h7m : Diagnostic test results are stored on file: flash:/TestReport-CP-unit.txt
Apr 26 22:36:01: %SYSTEM:LP %DIAGAGT-6-DA_DIAG_DONE: Diags finished on CP unit
2d3h7m : Recommended to reboot the system after diagnostics!!!
Dell#dir flash:
Directory of flash:
1 drwx 4096 Jan 01 1980 00:00:00 +00:00 .
Debugging and Diagnostics
291