Users Guide

Request, hops = 0, XID = 0xda4f9503, secs = 0, hwaddr =
00:60:CF:20:7B:8C, teaddr = 0.0.0.0
00:12:40 : %RELAY-I-BOOTREQUEST: Forwarded BOOTREQUEST for
00:60:CF:20:7B:8C to 14.4.4.2
00:12:42 : %RELAY-I-PACKET: BOOTP REPLY (Unicast) received at interface
14.4.4.1 BOOTP Reply,
hops = 0, XID = 0xda4f9503, secs = 0, hwaddr = 00:60:CF:20:7B:8C, teaddr
= 113.3.3.17
00:12:42 : %RELAY-I-BOOTREPLY: Forwarded BOOTREPLY for 00:60:CF:20:7B:8C
to 113.3.3.254
00:12:42 : %RELAY-I-PACKET: BOOTP REQUEST (Unicast) received at
interface 113.3.3.17 BOOTP
Request, hops = 0, XID = 0xda4f9503, secs = 0, hwaddr =
00:60:CF:20:7B:8C, teaddr = 0.0.0.0
00:12:42 : %RELAY-I-BOOTREQUEST: Forwarded BOOTREQUEST for
00:60:CF:20:7B:8C to 14.4.4.2
00:12:42 : %RELAY-I-PACKET: BOOTP REPLY (Unicast) received at interface
14.4.4.1 BOOTP Reply,
hops = 0, XID = 0xda4f9503, secs = 0, hwaddr = 00:60:CF:20:7B:8C, teaddr
= 113.3.3.17
00:12:42 : %RELAY-I-BOOTREPLY: Forwarded BOOTREPLY for 00:60:CF:20:7B:8C
to 113.3.3.254
Dell#
Related
Commands
● ip helper-address – specifies the destination broadcast or host address for the DHCP server request.
● ip helper-address hop-count disable – disables the hop-count increment for the DHCP relay agent.
debug ip icmp
View information on the internal control message protocol (ICMP).
C9000 Series
Syntax
debug ip icmp [interface] [count value]
To disable debugging, use the no debug ip icmp command.
Parameters
interface (OPTIONAL) Enter the following keywords and slot/port or number information:
● For the Management interface, enter the keyword ManagementEthernet
then the slot/port information. The slot range is from 0 to 1 and the port range
is 0.
● For a Port Channel interface, enter the keywords port-channel then a
number. The range is from 1 to 128.
● For a Tunnel interface, enter the keywords tunnel then a number. The range
is from 1 to 16383.
● For a 10-Gigabit Ethernet interface, enter the keyword
TenGigabitEthernet then the slot/port information.
●
For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the
slot/port information.
● For a port extender (PE) Gigabit Ethernet interface, enter the keyword peGigE
then the pe-id/stack-unit/port information.
● For a VLAN, enter the keyword vlan then a number from 1 to 4094.
count value (OPTIONAL) Enter the keyword count then the count value. The range is from 1
to 65534. The default is Infinity.
Command Modes EXEC Privilege
Command
History
This guide is platform-specific. For command information about other platforms, refer to the relevant Dell
Networking OS Command Line Reference Guide.
884 IPv4 Routing