Dell™ 4310WX Projector User’s Guide
Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your projector. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. ____________________ Information in this document is subject to change without notice. © 2009 Dell Inc. All rights reserved.
Contents 1 Your Dell Projector . . . . . . . . . . . . . . . . . . About Your Projector 2 . . . . . . . . . . . . . . . . . Connecting Your Projector . Connecting to a Computer 6 7 . . . . . . . . . . . 9 . . . . . . . . . . . . . . . . 10 Connecting a Computer Using a VGA Cable . . . . 10 Monitor Loop-Through Connection Using VGA Cables . . . . . . . . . . . . . . . . . . . . . . . . 11 Connecting a Computer Using an RS232 cable . . . 12 . . . . 13 . . . . . . . . . . . . . . . .
Connection With Commercial RS232 Control Box . . . . . . . . . . . . . . . . . . . . . . 3 . . . 20 Using Your Projector . . . . . . . . . . . . . . . . 21 Turning Your Projector On . . . . . . . . . . . . . . . . 21 Turning Your Projector Off . . . . . . . . . . . . . . . . Adjusting the Projected Image . . . . . . . . . . . . . Raising the Projector Height . . . . . . . . . . . . Lowering the Projector Height . . . . . . . . . . . 24 . . . . . . . . . . . . . . . . . 25 . . . . . . .
OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 . . . . . . . . . . 50 . . . . . . . . . . . 50 . . . . . . . . . . . . . . . . 51 Managing the Projector From Web Management Configuring the Network Setting Accessing Web Management Managing Properties 4 Troubleshooting Your Projector Guiding Signals 43 . . . . . . . . 63 . . . . . . . . . . . . . . . . . . . . . 67 Changing the Lamp . . . . . . . . . . . . . . . . . . . . 69 . . . . . . . . . . . . . . . . . . . . . 71 .
Your Dell Projector 1 Your projector comes with all the items shown below. Ensure that you have all the items, and contact Dell™ if anything is missing. Package Contents Power cable 1.
About Your Projector Top View Bottom View 1 10 6 12 8 2 3 9 5 4 7 11 1 Control panel 2 Zoom tab 3 Focus ring 4 Lens 5 Elevator button for height adjustments 6 IR receivers 7 Lens cap 8 Mounting holes for ceiling mount: Screw hole M3 x 6.5mm depth.
6 Do not try to touch the ventilation outlet as it can become very hot after the projector has been turned on or immediately after it is turned off. 7 Do not look into the lens while the projector is on as it may cause injury to your eyes. 8 Do not place any objects near or in front of the projector or cover its lens while the projector is on as the heat may cause the object to melt or burn. NOTE: • Do not attempt to ceiling mount the projector yourself.
2 Connecting Your Projector 1 2 18 17 16 3 15 4 5 6 7 8 9 10 14 13 12 11 1 Composite video connector 10 Security cable slot 2 S-video connector 11 Audio output connector 3 VGA-A output (monitor loop-through) 12 Audio-B input connector 4 VGA-A input (D-sub) connector 13 Audio-A input connector 5 VGA-B input (D-sub) connector 14 Audio-C right-channel input connector 6 HDMI connector 15 Power cord connector 7 DisplayPort connector 16 Audio-C left-channel input connector
Connecting to a Computer Connecting a Computer Using a VGA Cable 1 2 3 1 Power cord 2 VGA to VGA cable 3 USB-A to USB-B cable NOTE: The USB cable is not provided with your projector. NOTE: The USB cable must be connected if you want to use the Page Up and Page Down features on the remote control.
Monitor Loop-Through Connection Using VGA Cables 1 2 1 Power cord 2 VGA to VGA cable 2 NOTE: Only one VGA cable is shipped with your projector. An additional VGA cable can be purchased on the Dell website at dell.com.
Connecting a Computer Using an RS232 cable 1 2 1 Power cord 2 RS232 cable NOTE: The RS232 cable is not shipped with your projector. Consult a professional installer for the cable and RS232 remote control software.
Connecting a Computer Using a DisplayPort cable 1 2 1 Power cord 2 DisplayPort cable Connecting Your Projector 13
Connecting a DVD Player Connecting a DVD Player Using an S-video Cable 1 2 1 Power cord 2 S-video cable NOTE: The S-video cable is not shipped with your projector. You can purchase the S-Video extension (50 ft/100 ft) cable on the Dell website at dell.com.
Connecting a DVD Player Using a Composite Video Cable 1 2 1 Power cord 2 Composite video cable NOTE: The Composite Video cable is not shipped with your projector. You can purchase the Composite Video Extension (50 ft/100 ft) cable on the Dell website at dell.com.
Connecting a DVD Player Using a Component Video Cable 1 2 1 Power cord 2 VGA to Component Video cable NOTE: The VGA to Component Video cable is not shipped with your projector. You can purchase the VGA to Component Video Extension (50 ft/100 ft) cable on the Dell website at dell.com.
Connecting a DVD Player Using an HDMI Cable 1 2 1 Power cord 2 HDMI cable NOTE: The HDMI cable is not shipped with your projector.
Connecting to Local Area Network To control the projector that is connected to a network through an RJ45 cable. 1 2 Local Area Network (LAN) 1 Power cord 2 RJ45 cable NOTE: The RJ45 cable is not shipped with your projector.
Professional Installation Options: Installation for Driving Automatic Screen 1 3 2 1 Power cord 2 12V DC Plug 3 Automatic Screen NOTE: Use the dimension of 12V DC plug in 1.7 mm (ID) x 4.00 mm (OD) x 9.5 mm (shaft) to connect the automatic screen with the projector.
Connection With Commercial RS232 Control Box 1 3 2 1 Power cord 2 RS232 cable 3 Commercial RS232 control box NOTE: The RS232 cable is not shipped with your projector. Consult a professional technician to obtain the cable.
3 Using Your Projector Turning Your Projector On NOTE: Turn on the projector before you turn on the source (computer, DVD player, etc.). The Power button light blinks blue until pressed. 1 Remove the lens cap. 2 Connect the power cord and appropriate signal cables. For information about connecting the projector, see "Connecting Your Projector" on page 9. 3 Press the Power button (see "Using the Control Panel" on page 25 to locate the Power button). 4 Turn on your source (computer, DVD player, etc.
3 To power off the projector quickly, press the Power button and hold for 1 second while the projectors cooling fans are still running. NOTE: Before you turn on the projector again, wait for 60 seconds to allow the internal temperature to stabilized. 4 Disconnect the power cord from the electrical outlet and the projector. Adjusting the Projected Image Raising the Projector Height 1 Press the Elevator button.
Adjusting the Projector Zoom and Focus CAUTION: To avoid damaging the projector, ensure that the zoom lens and elevator foot are fully retracted before moving the projector or placing the projector in its carrying case. 1 Rotate the zoom tab to zoom in and out. 2 Rotate the focus ring until the image is clear. The projector focuses at distances ranging between 3.94 ft to 32.81 ft (1.2 m to 10 m).
Adjusting Projection Image Size 358"(909.32cm) ( 8 " m) 2 9 92c 6. 5 7 325"(825.5cm) 24 253"(642.62cm) ( ) 8" 2 0 2cm .3 8 52 ( 180"(457.2cm) ) 9" 1 4 6cm .4 8 37 108"(274.32cm) ) " 8 9 6cm .0 Using Your Projector 9.8'(3.0m) 16.4'(5.0m) 23.0'(7.0m) ( 29.5'(9.0m) 32.8'(10.0m) Projector to screen distance ( 8 " m) 2 6 72c . 0 68 6 22 36" (91.44cm) 3.9'(1.2m) 43 "(109.
Screen (Diagonal) Max. 43" (109.22cm) 108" (274.32cm) 180" (457.2cm) 253" (642.62cm) 325" (825.50cm) 358" (909.32cm) Min. 36" (91.44cm) 89" (226.06cm) 149" (378.46cm) 208" (528.32cm) 268" (680.72cm) 298" (756.92cm) 91.73" X 57.48" 153.15" X 95.67" 214.17" X 133.86" 275.20" X 172.05" 303.54" X 189.76" (233cm X 146cm) (389cm X 243cm) (544cm X 340cm) (699cm X 437cm) (771cm X 482cm) 75.59" X 47.24" 126.38" X 78.74" 176.77" X 110.24" 227.17" X 142.13" 252.36" X 157.
1 LAMP warning light If the LAMP amber indicator is on or blinking, one of the following problems could be occurring: • Lamp is reaching its end of usable life • Lamp module is not properly installed • Lamp driver failure • Color wheel failure For more information, see "Troubleshooting Your Projector" on page 63 and "Guiding Signals" on page 67.
7 Down / Keystone adjustment Press to navigate through the On-Screen Display (OSD) Menu items. Press to adjust image distortion caused by tilting the projector (+40/-35 degrees). 8 Menu 9 Left Press to activate the OSD. Use the directional keys and the Menu button to navigate through the OSD. / Source Press to navigate through the On-Screen Display (OSD) Menu items.
Using the Remote Control 1 11 2 12 3 4 13 5 14 15 6 7 16 8 17 18 9 19 10 20 1 Power 2 Enter Press to confirm the selection. 3 Right Press to navigate through the On-Screen Display (OSD) Menu items. 4 Down Press to navigate through the On-Screen Display (OSD) Menu items. 28 Turns the projector on or off. For more information, see "Turning Your Projector On" on page 21 and "Turning Your Projector Off" on page 21.
5 Aspect Ratio Press to change aspect ratio of a displayed image. 6 Page up Press to move to previous page. NOTE: The USB cable must be connected if you want to use the Page Up feature. 7 Mute Press to mute or un-mute the projector speaker. 8 Page down Press to move to next page. NOTE: The USB cable must be connected if you want to use the Page Down feature.
19 Auto adjust Press to synchronize the projector with the input source. Auto adjust does not operate if the OSD is displayed. 20 Keystone adjustment Press to adjust image distortion caused by tilting the projector (+40/-35 degrees).
Installing the Remote Control Batteries NOTE: Remove the batteries from the remote control when not in use. 1 Press the tab to lift the battery compartment cover. 1 2 Check the polarity (+/-) marking on the batteries. 2 3 Insert the batteries and align their polarity correctly 3 according to the marking in the battery compartment. NOTE: Avoid mixing different types of batteries or using new and old batteries together. 4 Slip the battery cover back.
Operating Range With Remote Control Distance Angle Operating range Angle ±30° Distance 10m/32.8feet Angle e nc sta Di NOTE: Actual operating range may slightly differ from the diagram. Weak batteries will also prevent the remote control from properly operating the projector.
Using the On-Screen Display • The projector has a multi-language On-Screen Display (OSD) Menu that can be displayed with or without an input source. • To navigate through the tabs in the Main Menu, press the or buttons on your projectors control panel or remote control. • To select a submenu, press the button on your projector’s control panel or remote control. • To select an option, press the or buttons on your projector’s control panel or remote control. The color changes to dark blue.
INPUT SELECT The Input Select menu allows you to select your projector’s input source. AUTO SOURCE—Select Off (the default) to lock the current input signal. If you press the Source button when the Auto Source mode is set to Off, you can manually select the input signal. Select On to auto detect the available input signals. If you press the Source button when the projector is on, it automatically finds the next available input signal. VGA-A—Press to detect VGA-A signal.
HDMI—Use and DISPLAYPORT—Use to enable or disable HDMI input. and to enable or disable DisplayPort input. NOTE: You cannot disable your current input source. At anytime, a minimum of two input sources have to be enabled. PICTURE (in PC Mode) Using the Picture menu, you can adjust the display settings of your projector.
PICTURE (in Video Mode) Using the Picture menu, you can adjust the display settings of your projectors. The Picture menu, provides the following options: VIDEO MODE—Allows you to optimize the display image: Presentation, Bright, Movie, sRGB (provides more accurate color representation), and Custom (set your preferred settings).If you adjust the settings for Brightness, Contrast, Saturation, Sharpness, Tint, and Advanced, the projector automatically switches to Custom.
PICTURE ADVANCED Using the Picture Advanced menu, you can adjust the display settings of your projector. The Picture Advanced menu provides the following options: WHITE INTENSITY—Use and to adjust the display white intensity. COLOR TEMP—Allows you to adjust the color temperature. The screen appears cooler at higher color temperatures and warmer at lower color temperatures. When you adjust the values in the Color Adjust menu, the Custom mode is activated. The values are saved in the Custom mode.
• Original — Select Original to maintain the aspect ratio of image projected according to input source. • • 4:3 — The input source scales to fit the screen and projects a 4:3 image. Wide — The input source scales to fit the width of the screen to project a wide screen image. ZOOM—Press to activate Zoom menu. Select the area to zoom and press to view zoomed image. Adjust the image scale by pressing press to view. ZOOM NAVIGATION—Press menu. Use HORIZONTAL POSITION—Press image to the right.
DISPLAY (in Video Mode) Using the Display menu, you can adjust the display settings of your projector. The Picture menu, provides the following options: ASPECT RATIO—Allows you to select the aspect ratio to adjust how the image appears. • Original — Select Original to maintain the aspect ratio of image projected according to input source. • • 4:3 — The input source scales to fit the screen and projects a 4:3 image.
LAMP Using the Lamp menu, you can adjust the display settings of your projector. The Lamp menu provides the following options: LAMP MODE—Allows you to select between Normal and ECO mode. Normal mode operates at full power level. ECO Mode operates at a lower power level which may provide longer lamp life, quieter operation, and dimmer luminance output on the screen. LAMP HOUR—Displays the operating hours since the last lamp timer reset. LAMP HOUR RESET—Select Yes to reset the lamp timer.
LANGUAGE—Allows you to set the language for the OSD. Press Language menu. to activate the PROJECTOR MODE—Allows you to select the projector mode, depending upon how the projector is mounted. • Front Projection-Desktop — This is the default option. • Front Projection-Ceiling Mount — The projector turns the image upside down for ceiling-mounted projection. • Rear Projection-Desktop — The projector reverses the image so that you can project from behind a translucent screen.
NETWORK—Select On to activate network connection. Select Off to disable network connection. Press to activate Network menu. See "NETWORK" on page 42. NETWORK The Network menu allows you to configure the network connection settings. DHCP—If a DHCP server exists in the network to which the projector is connected, the IP address will automatically be acquired when you select DHCP On. If DHCP is Off, manually set the IP Address, Subnet Mask, and Gateway.
INFORMATION The Information menu displays the current projector settings. OTHERS The Others menu allows you to change settings for Menu, Screen, Audio, Power, Security, and Closed Caption (for NTSC only). You can also perform Test Pattern and Factory Reset. MENU SETTINGS—Select and press to activate menu settings. The menu settings consists of the following options: MENU POSITION—Allows you to change the position of the OSD menu on the screen.
MENU TRANSPARENCY—Select to change the transparency level of the OSD background. MENU TIMEOUT—Allows you to adjust the time for an OSD timeout. By default, the OSD disappears after 20 seconds of non-activity. MENU LOCK—Select On to enable Menu Lock and hide the OSD menu. Select OFF to disable the Menu Lock. If you want to disable the Menu Lock function and have the OSD disappear, press the Menu button on the control panel or remote control for 15 seconds, then disable the function.
AUDIO INPUT—Select the Audio input source, options are: Audio-A, AudioB, Audio-C, HDMI and DisplayPort. VOLUME—Press to decrease the volume and to increase the volume. SPEAKER—Select On to enable speaker. Select Off to disable speaker. MUTE—Allows you to mute the sounds for audio input and audio output. POWER SETTINGS—Select and press to activate power settings. The power settings menu consists of the following options: POWER SAVING—Select Off to disable Power Saving mode.
SECURITY SETTINGS—Select and press to activate security settings. The security settings menu allows you to enable and set password protection. PASSWORD—When Password Protect is enabled, a Password Protect screen requesting you to enter a password will be displayed when the power plug is inserted into the electrical outlet and the power for the projector is first turned on. By default, this function is disabled. You can enable this feature, by selecting Enabled.
b Enabling the Password function will pop up a character screen, key in a 4-digit number from the screen and press . c To confirm, enter the password again. d If the password verification is successful, you may resume with accessing the projector's functions and its utilities. 2 If you have entered an incorrect password, you will be given another 2 chances. After the three invalid attempts, the projector will automatically turn off.
CHANGE PASSWORD—Key in the original password, then enter the new password and confirm the new password again. CLOSED CAPTION—Select On to enable close caption and activate the closed caption menu. Select an appropriate closed captions option: CC1, CC2, CC3, and CC4.
NOTE: Closed caption option is available for NTSC only. TEST PATTERN—Test Pattern is used to test focus and resolution. You can enable or disable the Test Pattern by selecting Off, 1 or 2. You can also invoke the Test Pattern 1 by pressing and holding down and buttons on the control panel simultaneously for 2 seconds. You can also invoke the test pattern 2 by pressing and holding down and buttons on the control panel simultaneously for 2 seconds.
Managing the Projector From Web Management Configuring the Network Setting If the projector is connected to a network, you can access the projector using a web browser by configuring the network setting (TCP/IP). When using the network function, the IP address should be unique. For configuring the network setting, refer to "NETWORK" on page 42. Accessing Web Management Use Internet Explorer 5.0 and above or Netscape Navigator 7.0 and above and enter the IP address.
Managing Properties Home • Access the Web Management Home page by entering the projector’s IP address at the web browser. See "NETWORK" on page 42. • Language: Allows you to set the language for web management.
Network Settings See OSD section on page 42. • Set up the Model Name, Projector Name, Location and Contact information (up to 21 characters for each field). Press Save to store the settings. • Choose DHCP to assign an IP address to the projector from a DHCP server automatically, or Manual to assign an IP address manually.
Projector Status and Control Page • Projector Status: There are 4 status: Lamp On, Standby, Power Saving and Cooling. Click the Refresh button to refresh the status and control settings. • Power Saving: Power Saving can be set to Off, 30, 60, 90, or 120 minutes. Refer to page 45. • Alert Status: There are 4 error status: Lamp warning, Low lamp life, Temperature warning, and Non-original lamp error. Your projector might lock up in protection mode if any of the alerts is activated.
- Bright: Maximum brightness and contrast. - Movie: For viewing movie & photo. - sRGB: Provide a more accurate color representation. - Custom: User preferred settings. • Blank Screen: You can select On or Off. • Aspect Ratio: Allows you to select the aspect ratio to adjust how the image appears. • Brightness: Select value to adjust the brightness of the image. • Contrast: Select value to adjust the display contrast.
E-mail Alert • E-mail Alert: You can set whether to be notified by email (Enable) or not (Disable). • To/CC/From: You can enter email address of sender (From) and recipients (To/Cc) to receive notification when an abnormality or warning occurs. • Alert Condition: You can select the abnormalities or warnings to be notified by email. When any of the alert conditions occur, an email will be sent to the recipients (To/Cc).
Password Setting Use Password Setting to set up an administrator password to access the Web Management. When enabling password for the first time, set the password before enabling it. When the password function is enabled, the administrator password will be required for accessing the Web Management. • New Password: Enter new password • Confirm Password: Enter password again and submit • Write Community: Set security for SNMP. Enter password and submit.
Login Page • Administrator Password: Enter the Administrator Password and click Login.
Firmware Update Use the Firmware Update page to update your projector’s firmware. Press Update to start. • 58 Please wait till the count reaches 0.
• Wait for 3 seconds and it will proceed to the next step automatically. • Select the file to upgrade and click the Upgrade button. When upgrading is in progress, the Cancel button is disabled.
• Please wait till the count reaches 0. • When upgrade is complete, please click the ReLogin button to go back to the Web Management Home Page.
TIPS: I would like remote access the projector via Internet. What is the better setting for the browser? To have a better setting for the browser, please follow the steps below: 1 Open Control Panel Internet Options General tab Temporary Internet Files Settings Tick Every visit to the pages. 2 Some firewall or anti-virus may block the HTTP application, if possible turn off the firewall or anti-virus. I would like to remote access the The following are TCP/IP socket ports which projector via Internet.
Why am I unable to access the SMTP server? Why am I unable to receive the test alert email even though the projector already indicates the test mail is already sent? 62 Using Your Projector 1 Check with your MIS or network administrator whether the SMTP server function is open for the projector and the IP assigned to the projector is allowed to access the SMTP server. The projector’s SMTP socket port number is 25, this cannot be changed.
Troubleshooting Your Projector 4 If you experience problems with your projector, see the following troubleshooting tips. If the problem persists, contact Dell™. See Contacting Dell™ on page 76. Problem Possible Solution No image appears on the screen • Ensure that the lens cap is removed and the projector is turned on. • Ensure that the INPUT SELECT is set correctly in the OSD menu. • Ensure the external graphics port is enabled. If you are using a Dell™ portable computer, press (Fn+F8).
Problem (continued) Partial, scrolling, or incorrectly displayed image Possible Solution (continued) 1 Press the Auto Adjust button on the remote control or the control panel. 2 If you are using a Dell™ portable computer, set the resolution of the computer to WXGA (1280 x 800) or XGA (1024 x 768): a Right-click the unused portion of your Microsoft® Windows® desktop, click Properties and then select Settings tab. b Verify that the setting is 1280x800 or 1024 x 768 pixels for the external monitor port.
Problem (continued) Possible Solution (continued) The image is stretched when displaying a 16:9 DVD The projector automatically detects the input signal format. It will maintain the aspect ratio of the projected image according to input signal format with an Original setting. If the image is still stretched, adjust the aspect ratio in the Set Up menu in the OSD. Image is reversed Select Set Up from the OSD and adjust the projector mode.
Problem (continued) Possible Solution (continued) TEMP light is blinking amber A projector fan has failed and the projector will automatically shut down. Try to clear the projector mode by pressing and holding the POWER button for 10 seconds. Please wait for about 5 minutes and try to power up again. If the problem persists, contact Dell™. The OSD does not appear on the screen Try to press the Menu button on the panel for 15 seconds to unlock the OSD. Check the Menu Lock on page 44.
Guiding Signals Projector Status Control Buttons Description Indicator Power Menu Others TEMP (Amber) LAMP (Amber) Standby mode Projector in Standby mode. Ready to power on. BLUE Flashing OFF OFF OFF OFF Warming up mode Projector takes some time to warm up and power on. BLUE BLUE BLUE OFF OFF Lamp on Projector in Normal mode, ready to display an image. Note: The OSD menu is not accessed. BLUE BLUE OFF OFF OFF Cooling mode Projector is cooling to shutdown.
Lamp failure Lamp is defective. Replace the lamp. OFF OFF OFF OFF AMBER Fault - DC supply (+12V) Power supply has been interrupted. The projector automatically shuts down. Unplug the power cord after three minutes and then turn on the projector. If this problem persists, contact Dell. AMBER Flashing OFF OFF AMBER AMBER Fault - DC supplies (secondary) Power supply has been interrupted. The projector automatically shuts down.
Changing the Lamp CAUTION: Before you begin any of the procedures in this section, follow the Safety Instructions as described on page 7. Replace the lamp when the message "Lamp is approaching the end of its useful life in the operation. Replacement suggested! www.dell.com/lamps" appears on the screen. If this problem persists after replacing the lamp, contact Dell™. For more information, see Contacting Dell™on page 76.
9 Reset the lamp usage time by selecting "Yes" for Lamp Reset in the OSD Lamp tab (see Lamp menu on page 40). When a new lamp module has been changed, the projector will automatically detect and reset the lamp hours. CAUTION: Lamp Disposal (for the US only) LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR MORE INFORMATION, GO TO WWW.DELL.COM/HG OR CONTACT THE ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG.
5 Specifications Light Valve 0.65" WXGA DMD Type A, DarkChip2™ Brightness 3500 ANSI Lumens (Max.) Contrast Ratio 2000:1 Typical (Full On/Full Off) Uniformity 80% Typical (Japan Standard - JBMA) Number of Pixels 1280x800 (WXGA) Displayable Color 16.7M colors Color Wheel Speed 2X Projection Lens F-Stop: F/ 2.55~2.83 Focal length, f=18.2~21.8 mm 1.2X manual Zoom Lens Throw ratio =1.28~1.56 wide and tele Projection Screen Size 36~358 inches (diagonal) Projection Distance 3.94~32.81 ft (1.
Noise Level 35 dB(A) Normal mode, 32 dB(A) Eco mode Weight 6.35 lbs (2.88 kg) Dimensions (W x H x D) 11.26 x 4.33 x 9.76 inches (286 x 110 x 247.8 mm) 11.26"(2 86mm) 9. 76 "( 24 7. 8m m ) 4.
USB port: One USB slave for remote support. RS232 port: One mini-DIN 6-pins for RS232 communication. RJ45 port: One RJ45 connector for control of projector through network. 12V output: One 12V DC / 200mA max. relay output for driving automatic screen. DisplayPort: One DisplayPort (1.0) connector.
RS232 Pin Assignment RS232 Protocol • Communication Settings Connection settings Value Baud Rate: 19200 Data Bits: 8 Parity None Stop Bits 1 • Command types To pop up the OSD menu and adjust the settings.
Compatibility Modes (Analog/Digital) Resolution Refresh Rate (Hz) Hsync Frequency (KHz) Pixel Clock (MHz) 640 x 350 70.087 31.469 25.175 640 x 480 59.940 31.469 25.175 640 x 480 p60 59.940 31.469 25.175 720 x 480 p60 59.940 31.469 27.000 720 x 576 p50 50.000 31.250 27.000 720 x 400 70.087 31.469 28.322 640 x 480 75.000 37.500 31.500 848 x 480 60.000 31.020 33.750 640 x 480 85.008 43.269 36.000 800 x 600 60.317 37.879 40.000 800 x 600 75.000 46.875 49.
Contacting Dell For customers in the United States, call 800-WWW-DELL (800-9993355). NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell™ provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: 1 Visit support.
Appendix: Glossary ANSI LUMENS — A standard for measuring the brightness. It is calculated by dividing a square meter image into nine equal rectangles, measuring the lux (or brightness) reading at the center of each rectangle, and averaging these nine points. ASPECT RATIO — The most popular aspect ratio is 4:3 (4 by 3). Early television and computer video formats are in a 4:3 aspect ratio, which means that the width of the image is 4/3 times the height.
dB — decibel — A unit used to express relative difference in power or intensity, usually between two acoustic or electric signals, equal to ten times the common logarithm of the ratio of the two levels. Diagonal Screen — A method of measuring the size of a screen or a projected image. It measures from one corner to the opposite corner. A 9FT high, 12FT wide, screen has a diagonal of 15FT.
room. This is usually limited by focal range of the optics. Minimum Distance — The closest position that a projector can focus an image onto a screen. NTSC — National Television Standards Committee. North American standard for video and broadcasting, with a video format of 525 lines at 30 frames per second. PAL — Phase Alternating Line. A European broadcast standard for video and broadcasting, with a video format of 625 lines at 25 frames per second.
Index A Adjusting the Projected Image 22 Adjusting the Projector Height 22 lower the projector Elevator button 22 Elevator foot 22 Tilt adjustment wheel 22 Adjusting the Projector Zoom and Focus 23 Focus ring 23 Zoom tab 23 Audio Input 45 Audio Settings 44 Audio-B 9 Audio-C 9 audio-C 9 C Capture Screen 44 Changing the Lamp 69 Closed Caption 48 Connecting the Projector Composite video cable 15 Connecting a Computer Using a DisplayPort cable 13 Connecting a Computer with a RS232 cable 12 80 Index Connectin
9 Display (in Video Mode) 39 Input Select 34 Lamp 40 Main Menu 33 Others 43 Picture (in PC Mode) 35 Picture (in Video Mode) 36 Set Up 40 Contact Dell 6, 65, 69 Control Panel 25 D DC Adapter 9 Dell contacting 76 H HDMI 9 M Main Unit 7 Control panel 7 Elevator button 7 Focus ring 7 IR receiver 7 Lens 7 Zoom tab 7 Menu Position 43 Menu Settings 43 Menu Timeout 44 Menu Transparency 44 Mute 45 O On-Screen Display 33 Auto-Adjust 35 Display (in PC Mode) 37 P Password 46 phone numbers 76 Power Saving 45 Powe
Screen Settings 44 V Security Settings 46 Volume 45 Speaker 45 Specifications Audio 71 Brightness 71 Color Wheel Speed 71 Contrast Ratio 71 Dimensions 72 Displayable Color 71 Environmental 72 I/O Connectors 72 Lamp 73 Light Valve 71 Noise Level 72 Number of Pixels 71 Power Consumption 71 Power Supply 71 Projection Distance 71 Projection Lens 71 Projection Screen Size 71 RS232 Protocol 74 Uniformity 71 Video Compatibility 71 Weight 72 support contacting Dell 76 T telephone numbers 76 Test Pattern 49 Tro
