Users Guide
Table Of Contents
- Dell™ 2355dn Laser MFP User’s Guide
- Contacting Dell
- Finding Information
- Contents
- Unpacking Your Printer
- About Your Printer
- Introducing the Home Screen
- Internal Fonts
- Setting up the hardware
- Installing the Toner Cartridge
- Loading Paper
- Making Connections
- Powering On the Printer
- Dell 2355dn Laser MFP Menu Functions
- Printing the Printer setting and Op-panel Menu setting
- Setting the Machine ID
- Changing the Display Language
- Selecting Country
- Power Save Mode
- Setting the Sound/Volume
- Setting Daylight Savings Time (Only for USA)
- Scanner Lamp Power Save Mode
- Changing the Default Mode
- Setting the Time Out Option
- Setting the Job Management
- Setting the Toner Save Mode
- Setting the Timing of Toner Low Alert
- Ignoring Blank Pages
- Ignoring the Toner Low Message (Only for Fax)
- Software Overview
- Dell Printer Configuration Web Tool
- Installing Software in Microsoft® Windows® Operating System
- Uninstalling Software
- Using the Dell Toner Management System
- Printer Settings Utility
- Firmware Update Utility
- Set IP Address Utility
- Paper Handling
- Printing
- Copying
- Scanning
- Scanning Overview
- SmarThru Office
- Scanning Using Dell Scan Manager
- Scanning to a PC Application
- Scanning and Sending an Email
- Scanning and Sending to SMB Server
- Scanning and Sending to FTP Server
- Scanning and Sending Custom Email
- Scan to Fax Server
- Scanning Using the Windows Image Acquisition (WIA) Driver
- Scanning to the USB Memory
- Managing the USB Memory
- Scan to Email Setup
- Scanning by a network connection
- Setting up Address Book
- Group Numbers
- Changing Default Settings
- Networking
- Faxing
- Macintosh
- Linux
- Maintenance
- Troubleshooting
- Installing Accessories
- Specifications
- Index
284
Half the page is blank. The page orientation
setting may be incorrect.
Change the page orientation in your application. See "Basic Tab".
The paper size and the
paper size settings do not
match.
Ensure that the paper size in the printer driver settings matches the
paper in the tray.
The printer prints,
but the text is wrong,
garbled, or
incomplete.
The printer cable is loose or
defective.
Disconnect the printer cable and reconnect. Try a print job that you
have already printed successfully. If possible, attach the cable and
the printer to another computer and try a print job that you know
works. Finally, try a new printer cable.
The wrong printer driver
was selected.
Check the application’s printer selection menu to ensure that your
printer is selected.
The software application is
malfunctioning.
Try printing a job from another application.
The operating system is
malfunctioning.
Exit Windows and reboot the computer. Power the printer off and
then back on again.
Pages print, but are
blank.
The toner cartridge is
defective or out of toner.
Thoroughly shake the toner. See "
Redistributing Toner".
If necessary, replace the toner cartridge.
The file may have blank
pages.
Check the file to ensure that it does not contain blank pages.
Some parts, such as the
controller or the board, may
be defective.
Contact a service representative.
The illustrations print
incorrectly in Adobe
Illustrator.
The setting in the software
application is wrong.
Print the document by selecting
Download as Bit Image
in the
Advanced window of the Graphic properties.
The print quality of
photos is not good.
Images are not clear.
The resolution of the photo
is very low.
Reduce the photo size. If you increase the photo size in the
software application, the resolution will be reduced.
The machine prints,
but the text is wrong,
garbled, or
incomplete.
If you are under the DOS
environment, the font
setting for your machine
may be set incorrectly.
Suggested solutions: Change the language setting. See "
Printer
Settings Utility".
Before printing, the
machine emits vapor
near the output tray.
Using damp paper can
cause vapor during printing.
This is not a problem. Just keep printing.
Condition Possible cause Suggested solutions