Dell™ 2200MP Projector User's Guide The information below is provided by the supplier of the referenced device without independent verification by Dell and is subject to the restrictions and disclaimers. Safety Instructions (Read before connecting the projector) About Your Projector Installation Using Your Projector Troubleshooting Specifications Regulatory Notices Contacting Dell Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your projector.
Back to Contents Page Safety Instructions: Dell™ 2200MP Projector CAUTION Use the following safety guidelines to help protect your projector from potential damage and to ensure your own personal safety: The surface beneath the projector might be hot with use. Be careful in handling the unit. The lamp becomes very hot with use. Do not attempt to replace the lamp after use until the projector has been allowed to cool down for at least 30 minutes, and follow all instructions in "Changing the Lamp.
Back to Contents Page About Your Projector: Dell™ 2200MP Projector Features Equipment Main Unit Control Panel Connection Ports Remote Control Features Single chip 0.55" Texas Instruments DLP™ technology High contrast, double data rate (DDR) digital micromirror device True SVGA, 800 x 600 addressable pixels 4.7 lbs (2.14 kgs) lightweight compact design 1200 ANSI lumens brightness (Max)* 1700:1 full on / full off contrast ratio 1.
Main unit 3.0m Power cord 1.8m VGA cable (D-sub to D-sub) 2.0m S-video cable 1.8m USB cable 1.8m Composite Video cable 1.8m D-sub to YPbPr cable 1.8m RCA to Audio cable 1.8m mini pin to mini pin cable Remote control Dell 2200MP Projector User's Guide Dell 2200MP Projector Quick Start Card Warranty Guide Owner's Manual Carrying case Batteries (2) http://www.pureglare.com.
Main Unit 1 Control panel 2 Zoom tab 3 Focus ring 4 Lens 5 Elevator button 6 Remote control receiver 1 Power button 2 Four directional keys 3 Keystone adjustment 4 Temperature warning light Control Panel http://www.pureglare.com.
5 Lamp warning light 6 Resync 7 Menu 8 Keystone adjustment 9 Source 1 VGA in (D-sub) connector 2 VGA out (monitor loop-through) 3 IR receiver 4 USB connector 5 S-video connector 6 Composite video connector 7 Audio input connector Connection Ports Remote Control http://www.pureglare.com.
1 Light 2 Power button 3 Previous Page button (page up) 4 Four Direction buttons 5 Source button 6 Resync button 7 Keystone Correction button 8 Volume button 9 Hide button 10 4:3/16:9 (aspect ratio) button 11 Menu button 12 Next Page button (page down) 13 Video Mode button Battery Disposal: Your projector remote control uses zinc-manganese batteries. If you need to replace the batteries, see your Dell 2200MP Projector Quick Start Card.
Back to Contents Page http://www.pureglare.com.
Back to Contents Page Installation: Dell™ 2200MP Projector Connecting the Projector Powering On/Off the Projector Adjusting the Projected Image Changing the Lamp Connecting the Projector A. To Computer 1 Power cord 2 D-sub to D-sub cable 3 USB to USB cable B. To DVD Player: There are three possible methods of connecting to a DVD player. 1. Connecting with component cable: http://www.pureglare.com.
1 Power cord 2 D-sub to HDTV/Component cable 2. Connecting with S-video cable: 1 Power cord 2 S-video cable 3. Connecting with composite cable: http://www.pureglare.com.
1 Power cord 2 Composite video cable Powering On/Off the Projector Powering On the Projector NOTE: Turn on the projector before you turn on the source. 1. Remove the lens cap. 2. Ensure that the power cord and appropriate signal cable(s) are securely connected. The power button light will blink green. 3. Press the power button to turn on the projector. The Dell logo will be displayed for 30 seconds. 4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.
1 Power button 2 Lens cap Powering Off the Projector DO NOT UNPLUG THE PROJECTOR BEFORE PROPERLY SHUTTING DOWN USING THE FOLLOWING STEPS. 1. Press the power button to turn off the projector. The "Power Off the Lamp?" message appears on the OSD. 2. Press the power button again. The cooling fans continue to operate for 2 minutes. 3. If the LAMP light is solid orange, replace the lamp. 4. If the TEMP light is solid orange, the projector has overheated. The display automatically shuts down.
Notice: To avoid damaging the projector, make sure that the zoom lens and elevator foot are fully retracted before placing the projector in its carrying case. 1 Elevator button 2 Elevator foot 3 Tilt adjustment wheel Adjusting the Projector Zoom and Focus 1. Rotate the zoom tab to zoom in and out. 2. Rotate the focus ring until the image is clear. The projector focuses at distances from 3.9 ft to 39.4ft (1.2 m to 12 m).
Max. Screen (Diagonal) Min. Screen Size Max. (WxH) Min. (WxH) 33.7" (85.7cm) 27.9" (70.8cm) 27.0"X20.2" 95.6" (242.9cm) 78.9" (200.5cm) 76.5"X57.4" 154.7" (392.9cm) 127.7" (324.3cm) 123.7"X92.8" 216.5" (550.0cm) 178.7" (454.0cm) 173.2"X129.9" 275.6" (700.0cm) 227.5" (577.8cm) 220.5"X165.4" 337.5" (857.1cm) 278.6" (707.5cm) 270.0"X202.5" (68.6cmX51.4cm) (194.3cmX145.7cm) (314.3cmX235.7cm) (440.0cmX330.0cm) (560.0cmX420.0cm) (685.7cmX514.3cm) 22.3"X16.7" 63.1"X47.4" 102.1"X76.6" 143.0"X107.2" 182.
6. Reverse steps 1 through 5 to install the new lamp. 7. Reset the lamp by selecting the left Lamp Reset icon in the OSD Management tab. 8. Dell may require that lamps replaced under warranty are returned to Dell. Otherwise, contact your local waste disposal agency for the address of the nearest deposit site. 9. The lamp contains mercury. Disposal of this material may be regulated due to environmental considerations.
Back to Contents Page Using Your Projector: Dell™ 2200MP Projector Control Panel Remote Control On-Screen Display Control Panel Power See "Powering On/Off the Projector." Source Press to step through Analog RGB, Composite, Component-I, S-video, and Analog YPbPr sources when multiple sources are connected to the projector. Resync Press to synchronize the projector to the input source. Resync will not operate if the OSD (On-Screen Display) is displayed. Menu Press to activate the OSD.
Power See "Power On/Off the Projector." Source Press the Source button to choose Analog RGB, Composite, Component-I, S-video, and Analog YPbPr sources. Resync Press to synchronize the projector to the input source. Resync will not operate if the OSD (On-Screen Display) is displayed. Directional Keys Use or to select OSD items, use "left" and "right" button to make adjustments. Hide Press Hide button to hide the image, press again to resume display of the image.
Keystone Adjusts image distortion caused by tilting the projector. ( ±16 degrees) On-Screen Display The projector has a multi-language On-Screen Display (OSD) that can only be displayed when an input source is present. The OSD allows you to make image adjustments and change a variety of settings. If the source is a computer, the OSD allows changes to the Computer Image tab. When using a video source, the OSD allows changes to the Video Image tab. The projector automatically detects the source.
Brightness Adjusts the brightness of the image. Press to darken the image. Press to lighten the image. Contrast Controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image. Press to decrease the contrast. Press to increase the contrast. Color Temp. Adjusts the color temperature. With the higher temperature, the screen looks colder; with the lower temperature, the screen looks warmer.
This mode allows for manual adjustment of red, green, and blue color settings. Modifying these values will automatically change the color temperature to "user". Keystone Adjusts image distortion caused by tilting the projector. (±16 degrees) Aspect Ratio Select this function to fit 16:9U, 1:1, 16:9, 4:3 aspect ratio.
Degamma can be adjusted between 1 and 7. Default setting is 3 (Recommended). Adjustment of the setting will change the color performance of the display. Audio Menu Audio Volume Press to decrease the volume. Press to increase the volume. Treble Control the higher frequencies of your audio source. Press to decrease the treble. Press to increase the treble. http://www.pureglare.com.
Bass Control the lower frequencies of your audio source. Press to decrease the bass. Press to increase the bass. Mute Select the left icon to mute the volume. Select the right icon to unmute the volume. Management Menu http://www.pureglare.com.
Management Menu Location Select the location of the OSD on the screen. Projection Mode Front Projection-Desktop The default setting. Rear Projection-Desktop The projector reverses the image so you can project from behind a translucent screen. Front Projection-Ceiling Mount The projector turns the image upside down for ceiling-mounted projection. Rear Projection-Ceiling Mount The projector simultaneously reverses and turns the image upside down.
Power Saving Use this function to select the power saving delay period. Press "Yes" to go into the "set time" sub menu. Set Time(Min) Set the power saving delay period as you prefer. When the projector is not receiving an input signal for the selected period of time, the projector will automatically enter power saving mode, and turn off the lamp. After a one-minute cooling period, the projector will turn back on with detection of an input signal or by pressing the "Power" button.
Turning on High Altitude mode operates the fans at full speed continuously to allow for proper high altitude cooling of the projector. Language Menu Language Language Press or to select the language you prefer. Factory Reset Menu http://www.pureglare.com.
Factory Reset Select Yes to reset the projector to its factory default settings. Reset items include both computer image and video image settings. Computer Image Menu Computer Image- Note: this menu is only available with computer input signal. Frequency Change the display data frequency to match the frequency of your computer graphic card. If you experience a vertical flickering bar, use the frequency function to make an http://www.pureglare.com.
adjustment. Tracking Synchronize the signal timing of the display with that of the graphic card. If you experience an unstable or flickering image, use the tracking function to correct it. Hor. Position (Horizontal Position) Press to move the image left. Press to move the image right. Ver. Position (Vertical Position) Press to move the image down. Press to move the image up. Video Image Menu Video Image- Note: this menu is only available with S-video, video(composite) signal.
Press to increase the amount of color in the image. Sharpness Adjust the sharpness of the image. Press to decrease the sharpness. Press to increase the sharpness. Tint Adjust the color balance of red and green. Press to increase the amount of green in the image. Press to increase the amount of red in the image. Back to Contents Page http://www.pureglare.com.
Back to Contents Page Troubleshooting: Dell™ 2200MP Projector No image appears on the screen Partial, scrolling, or incorrectly displayed image The screen does not display your presentation Image is unstable or flickering Image has vertical flickering bar Image color is not correct Image is out of focus The image is stretched when displaying 16:9 DVD Image is reversed Lamp is burned out or makes a popping sound Self-diagnostic for video Noise made when turning projector upside down If you experience proble
If you experience difficulty in changing resolutions or your monitor freezes, restart all the equipment and the projector. The screen does not display your presentation If you are using a portable computer, press . Image is unstable or flickering Adjust the tracking in the OSD Computer Image tab. Image has vertical flickering bar Adjust the frequency in the OSD Computer Image tab.
Video, S-video, Component-I). Use this advanced feature for preliminary self-diagnostic on your projector when encountering the display problem for video. After turning on the projector, press "+" and "-" buttons on the control panel simultaneously and release the buttons when screen goes blank. Contact Dell if the projector doesn't enter diagnostic mode or if the colors are incorrectly displayed. Press "+" and "-" buttons again to exit the diagnostic mode.
Back to Contents Page Specifications: Dell™ 2200MP Projector Light Valve single-chip DLP™ technology Contrast Ratio 1700:1 Typical (Full On/Full Off) Lamp 200-watt, user-replaceable lamp Number of Pixels 800 x 600 Displayable Color 16.7M colors Color Wheel Speed 120Hz(2X) Projection Lens F/2.4~2.7, f=19.7~23.6mm with 1.2x manual zoom lens Projection Screen Size 27.9-337.5 inches (diagonal) Projection Distance 3.9~39.4 ft (1.2m–12m) Video Compatibility NTSC, NTSC 4.
VGA 640X400 85 37.9 VGA 640X480 60 31.5 VGA 640X480 72 37.9 VGA 640X480 75 37.5 VGA 640X480 85 43.3 VGA 720X400 70 31.5 VGA 720X400 85 37.9 SVGA 800X600 56 35.2 SVGA 800X600 60 37.9 SVGA 800X600 72 48.1 SVGA 800X600 75 46.9 SVGA 800X600 85 53.7 *XGA 1024X768 43.4 35.5 *XGA 1024X768 60 48.4 *XGA 1024X768 70 56.5 *XGA 1024X768 75 60.0 *XGA 1024X768 85 68.7 *SXGA 1280X1024 60 63.98 *SXGA+ 1400X1050 60 63.98 MAC II 13 640X480 66.
Back to Contents Page Regulatory Notices: Dell™ 2200MP Projector Federal Communications Commission (FCC) Notice (U.S.
Coretronic Corporation We hereby declare that this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. * FCC Rules: Tested to comply with FCC part 15, class B * Test site at: Advance Data Technology Corporation No.
Canadian Regulatory Information (Canada Only) This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Note that Industry Canada regulations provided, that changes or modifications not expressly approved by Dell Inc. could void your authority to operate this equipment.
Please note that this device has been approved for non-business purposes and may be used in any environment, including residential areas. Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source.
NOM Information (Mexico Only) The following information is provided on the device(s) described in this document in compliance with the requirements of the official Mexican standards (NOM) Exporter: Dell Inc. One Dell Way Round Rock, TX 78682 Importer: Dell Computer de México, Paseo de la Reforma 2620, 11th Floor Col. Lomas Altas México DF CP 11950 Ship to: Dell Computer de Mexico, S.A. de C.V. al Cuidado de Kuehne & Nagel de México S. de R.I., Avenida Soles No. 55 Col.
EMC Certifications: FCC Part 15 Class B CE Mark--EN55022:1998 Class B, EN61003-3:1995, EN55024:1998, EN61000-3-2:1995, EN61000-33:1995 ICES-003 EZU PCBC C-Tick VCCI Class B ITE MIC Back to Contents Page http://www.pureglare.com.
Back to Contents Page Contacting Dell To contact Dell electronically, you can access the following websites: www.dell.com support.dell.com (technical support) premiersupport.dell.com (technical support for educational, government, healthcare, and medium/large business customers, including Premier, Platinum, and Gold customers) For specific web address for your country, find the appropriate country section in the table below. NOTE: Toll-free numbers are for use within the country for which they are listed.
Code:0011 Country Code:61 City Code:2 Austria (Vienna) International Access Code:900 Country Code:43 City Code:1 Home and Small Business 1-300-65-55-33 Government and Business toll free: 1-800-633559 Preferred Accounts Division (PAD) toll free: 1-800-060889 Customer Care toll free: 1-800-819339 Corporate Sales toll free: 1-800-808385 Transaction Sales toll free: 1-800-808312 Fax toll free: 1-800-818341 Switchboard 01 491 040 Home/Small Business Sales 01 795676-02 Home/Small Business Fa
Website: support.euro.dell.com E-mail: tech_be@dell.com E-mail for French Speaking Customers: support.euro.dell.com/be/fr/emaildell/ Bermuda General Support Bolivia General Support Brazil International Access Code:00 Country Code:55 City Code:51 1-800-890-0748 toll free: 800-100238 toll free: 0800 90 3355 Customer Support, Technical Support Technical Support Fax 51 481-5470 Customer Care Fax 51 481-5480 toll free: 0800 90 3390 Sales Website: www.dell.
Sales (direct-from outside Toronto) 1-800-387-5752 Sales (direct-from within Toronto) 416-758-2200 Sales (federal government, education, and medical) 1-800-567-7542 TechFax toll free: 1-800-9501329 1-800-805-7541 Cayman Islands General Support Chile (Santiago) Sales, Customer Support, and Technical Support toll free: 1230-0204823 Country Code:56 City Code:2 China (Xiamen) Country Code:86 City Code:592 Tech Support website: support.ap.dell.com/china Tech Support E-mail: cn_support@dell.
Large Corporate Accounts South toll free: 800 858 2355 Large Corporate Accounts West toll free: 800 858 2811 Large Corporate Accounts GCP toll free: 800 858 2055 Large Corporate Account Key Accounts toll-free:800-8582628 Large Corporate Accounts Spare Parts toll free: 800-858-2621 Colombia General Support Costa Rica General Support Czech Republic (Prague) Technical Support 02 22 83 27 27 Customer Care 02 22 83 27 11 International Access Code:00 Fax 02 22 83 27 14 TechFax 02 22 83
Nordic_server_support@dell.
01 Germany (Langen) Technical Support International Access Code:00 Global Segment Customer Care 06103 766-9570 Preferred Accounts Customer Care 06103 766-9420 Large Accounts Customer Care 06103 766-9560 Public Accounts Customer Care 06103 766-9555 Switchboard 06103 766-7000 Country Code:49 06103 55 94 71 00 Home/Small Business Customer Care 766-7200 0180-5-224 400 Website: support.euro.dell.com E-mail: tech_support_central_europe@dell.
UK Technical Support (dial within UK only) International Access Code:16 Country Code:353 0870 908 0800 Home User Customer Care 01 204 4095 Small Business Customer Care 01 204 4444 Corporate Customer Care 01 204 4003 0870 906 0010 01 204 4444 0870 907 4000 SalesFax 01 204 0144 Fax 01 204 5960 Switchboard 01 204 4444 Technical Support 02 577 826 90 Customer Care 02 696 821 14 Fax 02 696 821 13 Switchboard 02 696 821 12 Technical Support 02 577 826 90 Customer Care 02
Japan (Kawasaki) International Access Code:001 Country Code:81 Web site: support.jp.dell.
Transaction Sales toll free: 0800 581 Malaysia (Penang) Technical Support toll free: 1 800 888 298 International Access Code:00 Customer Service 4 Transaction Sales toll free: 1 800 888 202 Corporate Sales toll free: 1 800 888 213 Customer Technical Support 001-877-384-8979 Country Code:60 City Code: 4 Mexico International Access Code:00 633 4949 or 001-877-2693383 Sales 50-81-8800 or 01-800-888-3355 Country Code:52 Customer Service 001-877-384-8979 or001-877-2693383 Main 50-81-8800 or
New Zealand E-mail (New Zealand): nz_tech_support@dell.com E-mail (Australia): au_tech_support@dell.
E-mail: pl_support_tech@dell.com Portugal Technical Support International Access Code:00 Customer Care Country Code:35 35 800 834 077 800 300 415 or 800 834 075 Sales 800 300 410 or 800 300 411 or 800 300 412 or 121 422 07 10 Fax 35 121 424 01 12 E-mail: support.euro.dell.com/es/es/emaildell/ Puerto Rico General Support 1-800-805-7545 St. Kitts and Nevis General Support toll free:1-877-4414731 St. Lucia General Support 1-800-882-1521 St.
Spain (Madrid) Home and Small Business Technical Support 91 902 100 130 International Access Code:00 Customer Care 91 902 118 540 Sales 91 902 118 541 Switchboard 91 902 118 541 Fax 91 902 118 539 Technical Support 91 902 100 130 Customer Care 91 902 118 546 Switchboard 91 722 92 00 Fax 91 722 95 83 Country Code:34 City Code:91 Website: support.euro.dell.com E-mail: support.euro.dell.com/es/es/emaildell/ Corporate Website: support.euro.dell.com E-mail: support.euro.dell.
Country Code:41 Customer Care(Corporate) 0848 821 721 City Code:22 Switchboard 22 799 01 01 Fax 22 799 01 90 Website: support.euro.dell.com E-mail:swisstech@dell.com E-mail for French-speaking HSB and Corporate Customers: support.euro.dell.
Customer Care Central Government Customer Care 01344 373 193 Local Government & Education Customer Care 01344 373 199 Health Customer Care 01344 373 194 Home/Small Business Sales 0870 907 4000 Home/Small Business Customer Care 0870 906 0010 01344 860 456 Corporate/Public Sector Sales Website: support.euro.dell.com Customer Care website: dell.co.uk/lca/customerservices E-mail: dell_direct_support@dell.com Uruguay General Support toll free:000-413598-2521 U.S.A.
Dell Services for the Deaf, Hard-of-Hearing, or Speech-Impaired toll free: 1-877DELLTTY (1-877-335-5889) U.S. Virgin Islands General Support 1-877-673-3355 Venezuela General Support 8001-3605 Back to Contents Page http://www.pureglare.com.
