Datasheet

Wireless radio specications
• AP type: Indoor, dual radio, 5GHz and 2.4GHz 802.11n
2x2:2
• Software-congurable dual radio supports 5GHz (Radio
0) and 2.4GHz (Radio 1)
• 2x2 MIMO with two spatial streams and up to 300Mbps
wireless data rate
• Support for up to 32 associated client devices, and up to
8 BSSIDs per radio
• Supported frequency bands (country-specic
restrictions apply):
- 2.4000 to 2.4835GHz
- 5.150 to 5.250GHz
- 5.250 to 5.350GHz
- 5.470 to 5.725GHz
- 5.725 to 5.850GHz
• Available channels: Dependent on congured regulatory
domain
• Dynamic frequency selection (DFS) optimizes the use of
available RF spectrum
• Supported radio technologies:
- 802.11b: Direct-sequence spread-spectrum (DSSS)
- 802.11a/g/n: Orthogonal frequency-division multi-
plexing (OFDM)
• Supported modulation types:
- 802.11b: BPSK, QPSK, CCK
- 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM
• Transmit power: Congurable in increments of 0.5 dBm
• Maximum (aggregate, conducted total) transmit power
(limited by local regulatory requirements):
- 2.4GHz band: +21 dBm (18 dBm per chain)
- 5GHz band: +21 dBm (18 dBm per chain)
• ACC minimizes interference from cellular networks
• Maximum ratio combining (MRC) for improved receiver
performance
• Cyclic delay/shift diversity (CDD/CSD) for improved
downlink RF performance
• Short guard interval for 20MHz and 40MHz channels
• Space-time block coding (STBC) for increased range
and improved reception
• Low-density parity check (LDPC) for high-eciency
error correction and increased throughput
• Supported data rates (Mbps):
- 802.11b: 1, 2, 5.5, 11
- 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
- 802.11n: 6.5 to 300 (MCS0 to MCS15)
• 802.11n high-throughput (HT) support: HT 20/40
• 802.11n packet aggregation: A-MPDU, A-MSDU
Power
• Maximum (worst-case) power consumption: 9.4W (POE)
or 8.3W (DC)
• Maximum (worst-case) power consumption in idle
mode: 3.5W (POE) or 2.9W (DC)
• Direct DC source: 12V DC nominal, +/- 5%
• PoE: 48V DC (nominal) 802.3af compliant source
• Power sources sold separately
• When both power sources are available, DC power takes
priority
Antennas
• Two integrated dual-band omni-directional antennas
for 2x2 MIMO with maximum antenna gain of 3.6dBi in
2.4GHz and 3.3dBi in 5GHz. Antennas are optimized for
vertical wall mounted orientation of the AP.
Other interfaces
• 10/100/1000BASE-T Ethernet network interface (RJ-45)
- Auto-sensing link speed and MDI/MDX
- 802.3az Energy Ecient Ethernet (EEE)
- PoE-PD: 48V DC (nominal) 802.3af PoE or 802.3at
PoE+
• DC power interface, accepts 1.7/4.0-mm center-
positive circular plug with 9.5-mm length
• Serial console interface (proprietary; optional adapter
cable available)
• Visual indicator (single tri-color LED): power/system
status
• Dual-function push-button: factory reset (during device
power up) and LED on/o control (during normal
operation)
• Kensington security slot
Mounting
• Included with AP:
- Mounting plate for single-gang electrical/data
wall-box (various worldwide standards)
• Spare:
- AP-103H-MNT1: Mounting plate for single-gang
electrical/data wall-box (various worldwide standards)
• Accessory:
- AP-103H-MNT2: Mounting plate for dual-gang
electrical/data wall-box (various worldwide standards)
Mechanical
• Dimensions/weight (unit, excluding mounting
accessories):
- 140mm x 86mm x 30mm (H x W x D)
- 260g
• Dimensions/weight (unit, as mounted):
- 140mm x 86mm x 31mm (H x W x D)
- 305g
• Dimensions/weight (shipping):
- 168mm x 143mm x 49mm (H x W x D)
- 420g
• Access point attaches securely to mounting bracket
using built-in security features. Removing the unit from
the bracket requires a custom tool that ships with the
product.
Environmental
• Operating:
- Temperature: 0° C to +40° C (+32° F to +104° F)
- Humidity: 5% to 95% non-condensing
• Storage and transportation:
- Temperature: -40° C to +70° C (-40° F to +158° F)