Installation Guide

ManualsBrandsDelaney ManualsResidential KnobsDelaney Traditional Collection Ansley Series Grade 2 Keyed Entry Door Knob Set

Read this instruction carefully before attempting to

install lockset. Although an untrained person can

prepare a door, We recommend that a skilled

carpenter or locksmith do measurements and drilling.

2. Latch Face Plate

2B2A

2 /8"

2 /4"

2 /8"

2 /4"

Determine which latch mounting method will be used and make necessary adjustments.

2A. If you need a Square Cornered

Mortise Faceplate use as

assembled

(no adjustment necessary).

Proceed to step 3 if this is a new door

application and to step 4 if the lock is

a replacement (uses existing holes).

For Radius Cornered Mortise

Faceplate, remove squared

mortise plate.

Rotate the Square Cornered

Latch Faceplate clockwise 20

degrees and pull plate off back

of latch. Replace with Radius

Cornered Mortise Plate.

2B.

With Drive-In Latch installations,

rotate latch faceplate clockwise

20 degrees and pull plate off back

of latch (no faceplate is needed).

2C.

1. Latch Backset Adjustment

Before Proceeding：

Backset is the distance from the door edge to the center of lock, either 2-3/8" or 2-3/4".

Your latch was preset at the factory for 2-3/8" backset. If a 2-3/4" backset is required,

follow the adjustment instructions in Step 1A. If 2-3/8" backset is required, go to part 2A of

the instructions.

1A 1B 1C 1D

Right Wrong

1A.

If 2-3/4" backset is required,

pull spindle cam all the way

to the right edge of the

adjusting hole.

1B.

Be sure the 2-3/4" stem

hole is properly aligned.

It is important that the

stem hole remains properly

aligned through the installation.

1C.

Your latch is now set for

2-3/4" backset.

1D.

To reset the latch to 2-3/8"

backset, push spindle cam

to the left edge of the

adjusting hole.

Instructions for Knob or Lever

Lockset Installation for doors

1-3/8" to 1-3/4" thick.

RA2 RA2

3. New Door Preparation (if necessary)

3A, 3B, 3C, 3D

Tools required for new installation：

Phillips head screwdriver, 2-1/8" hole saw, 1"&1/8" drill, chisel.

Tools required for replacement installation：

Phillips screwdriver.

Fold template as marked and place on door. If corner of door is beveled,

place template on widest side of door.

Mark center for door edge for latch bolt as indicated on template.

Make center for hole on door face through guide on template for either

2-3/8" or 2-3/4" backset. Drill 1/8" pilot holes at center marks.

Drill 2-1/8" hole on the door face from both sides of door to prevent

splintering.

Drill 1" hole through door edge for latch bolt.

3D.

3A.

3B.

3C.

3E.

3F.

3E, 3F

OUTSIDE LEVER

(REVERSIBLE)

OUTSIDE KNOB

OUTSIDE ROSETTE

SCREW POST

SPINDLE

CYLINDER COLLAR

LATCH SCREWS

FACE PLATE

LATCH

ROTATION STEM

MOUNTING SCREWS

TURN PIECE

INSIDE ROSETTE

INSIDE KNOB

INSIDE LEVER

(REVERSIBLE)

LEVER SLEEVE

PAPER TAB

4. Install Latch

4A 4B

6. Remove Inside Mounting Assembly

4A.

4B.

4C.

4D.

For drive in application, drive the latch into the hole on edge of door and go to

step step 5.

For mortise application, insert latch into hole and trace outline of faceplate on

the edge of the door.

Chisel until latch face is flush with door edge.

Drill pilot holes for plate mounting screws. Insert latch bolt and tighten screws.

Curved edge of latch bolt should face in direction that door closes.

5. Strike Plate Installation

Close door until latch bolt touches door jamb to locate strike placement.

Mark horizontal centerline of strike parallel with the center of the latch bolt.

Measure one half of door thickness from doorstop and mark for the vertica

centerline of strike. Drill 1" hole, 1/2" deep at the intersection of the

horizontal and vertical centerlines.

Match screw holes on strike with centerlines on jamb. Mark outline of strike

plate and chisel out until strike is flush with jamb. (Approx. 1/8")

Install strike plate and tighten screws.

Adjustable tang on strike can be bent in or out to eliminate loose fit between

door and door stop.

5A.

5B.

5C.

5D.

5A 5B

5C 5D

Use handle tool (provided) to depress inside knob

catch through hole of inside trim collar. Pull knob

off of rosette/mounting plate assembly.

Pull up on paper tab to separate the mounting plate

from lock assembly. If the paper tab is missing.

Refer to 6C.

Alternate-if paper tab is missing：There is a 3/8"

wide space on the mounting plate. If the paper tab

is missing, push down on trim plate in this area with

screw driver to release trim from mounting plate.

6A.

6B.

6C.

7. Install Outside Knob or Lever

Place outside knob or lever over

the hole in the door face,

inserting spindle through latch.

Press outside assembly flush

against door.

Before proceeding, make sure

spindle hole in the latch is oriented

correctly.

For keyed sets, orient key cylinder

as shown.

8. Install Interior Mounting Assembly

Install interior mounting plate on the inside face of door.

Place machine screws into the holes in mounting plate,

through the door, into the female receivers on the

outside mounting plate and tighten securely.

Bold "snap the inside trim onto the mounting plate

(for proper fit, be sure to fit

notches in the trim into the

recesses on the mounting

plate).

See 9B if your lever set

requires reversing.

9A.

9B.

Knob： Align lug on knob with narrow slot on side of

spindle housing and push knob all the way in until

knob catch clicks into slot on knob.

Lever：Press down the lever catch in the collar hole with

handle tool and push inside lever all the way in until

catch clicks into catch slot.

All lever sets can be changed from right hand to left hand.

To change the handing of the levers：

˙Insert key (entrance sets only),rotate 1/4" turn the key counter clockwise.

˙Depress lever catch with the handle tool to release lever and pull lever off spindle

housing.

˙Replace inside lever by depressing the catch with the handle tool. Remove inside

lever.

˙Replace spacer on inside spindle housing

(entrance sets only) and reverse levers. (Outside lever to inside, inside lever to outside )

Push handles in until catch clicks. Make sure levers are retained by lever catch.

9. Install Inside Knob or Lever

RV、RQ series

Right Wrong

Wrong

Right

FOR BACKSET 2-3/8" (60mm)

FOR BACKSET 2-3/4" (70mm)

Mark 1" (25.4mm) hole at center of door edge.

2-1/8"(54mm)

1-9/16"

1-3/4"

1-3/8"

Fold on dotted line and fit on door edge

TEMPLATE