Installation Guide

ManualsBrandsDefiant ManualsTools & HardwareSingle Cylinder Satin Nickel Castle Electronic Keypad Deadbolt

TEMPLATE

Package Contents

WARRANTY

2-5/16" (58 mm) Mounting Bolt

1-13/16" (46 mm) Mounting Bolt

BB 13/16" (20 mm) Screw

CC 3/4" (19 mm) Wood Screw

Part

Description

Quantity

CAUTION:

Please use four alkaline batteries for the best performance.

CARE and MAINTENANCE:

The following instructions should be followed to properly protect and maintain your lockset:

Read the precautions and instructions in this manual before installing and using this lock. Save this manual for future reference.

A. Remove locks, or do not install locks, prior to painting your door.

B. Periodically clean with mild soap and a soft cloth only.

C. Do not use any abrasives or chemical products containing alcohol, benzene, acids, and avoid using sharp or abrasive objects to clean this lockset.

D. Do not allow any water or liquids into the lockset during installation.

A. Do not attempt to disassemble any internal components of the lockset. Doing so will void the limited warranty.

B. Do not drop or hit the lockset. Too much shock may result in permanent damage.

C. Do not use pins or sharp objects to press the keypad.

D. Always create a backup of information you wish to keep (programming code, user codes,etc.) Please use the last page of this booklet as a reference.

E. Promptly change the programming code before operating this lockset

Safety Information

WARNING:

If the door needs to be drilled, please be familiar with how to use a drill safely and understand all of the door preparation steps before proceeding.

Pre-installation – Tools Required / Hardware Included

Installation

Optional Optional Optional Optional Optional

I Dust Box

J Key

K Drive-in Collar (Optional)

L Exterior Gasket

E Interior Assembly 1

F Battery Cover 1

G Latch 1

H Strike Plate 1

A Exterior Assembly

B Power Cable

C Torque blade

D Mounting Plate

Part

Description

Quantity



Cut out TEMPLATE (reverse page) and use to mark the door, drill holes, and chisel out the mortise.

NOTE: Drill from both sides of the door to prevent wood splitting.

Pre-installation (continued) – Door Preparation

(25 mm)

2-1/8"(54 mm)

1-1/2"(38 mm)

Backset

Centerline

2-1/8"(54 mm)

1-1/2"(38 mm)

Note: For drive-in latch.

Simply insert latch.

1”

(25 mm)

Outline

Chisel 5/32” deep

Faceplate

NOTE: If your door is pre-drilled, check the hole sizes to make sure they are the proper size. If they are the proper size, skip to the INSTALLATION section.

Dust box

3/4"

Screws

Strike plate

Prepare the door jamb – use the strike plate as a template to drill the latch and screw holes and chisel out the mortise. The strike plate must fit flush with the surface

of the door jamb.



Door jamb hole dimension

Strike dimentions

b. 1-9/64"(29 mm)

d. 5/32"(4 mm)

e. 2-1/4"(57 mm)

f. 1"(25 mm)

a. 1-3/16"(30 mm)

c. 7/8"(22 mm)

A. Attach the correct faceplate

B. Set the latch backset length

C. Install the latch



INSTALLING THE LATCH

CAUTION: Be sure the latch cam is upright before making any backset adjustment.

Twist back

1/8 Turn

Turn back to retract the latch bolt.

Turn back

a.With the bolt extended,

twist latch end 1/8 turn.

b.Pull as shown in the diagram.

For 2-3/4"

backset.

Turn

Turn to extend the latch bolt.

Wood block (not included)

Drive-in latch

Tap latch ﬂush

Edge of door

Faceplate

Edge of door

Drive-in

collar

Flat head screwdriver

Backset

2-3/4 should be visible.

The cable must be arranged as shown in the diagram.

Insert screws (2)

and tighten.

Connect the cable

ﬁrmly into

connector port .

Remove the Battery Cover

The bulged part of the mounting plate

must face towards the door.

B. Install the lock assemblies

Slide the cable through the

notch in mounting plate.

INSTALLING THE LOCK ASSEMBLIES



The latch bolt should be

in retracted position.

Thread the cable through

the hole and under the latch.

For installation into 1-1/2”(38mm) bore hole,

simply pry the adapter collar off with a

screwdriver.

A. Door bore options

Adapter collar

CAUTION :

1.Please use four alkaline batteries for better performance.

2.Please set up the lock and perform bolt direction determination to complete the installation.

Install batteries

Install battery cover

Enter default programming code

(123456) and the lock will set up bolt

direction to complete installation.

LIMITED LIFETIME MECHANICAL AND 1 YEAR ELECTRONIC WARRANTY

The retailer of this product, hereby warrants, subject to the conditions set forth below, that it will either repair or replace, at its option, this product if it

proves to be defective by reason of improper workmanship or materials within the original purchaser's limited time. In order to obtain repairs or replace-

ment under this limited warranty you must bring this product to the retailer's store in which you bought it.

Original purchaser: This limited warranty is limited to the original purchaser at retail of this product from retailer.

Except to the extent prohibited by applicable law, no other warranties, whether express or implied, including the warranties of merchantability and ﬁtness

for a particular purpose, shall apply to this product. Under no circumstances shall retailer be liable for consequential or incidental damages in connection

with this product. To the extent retailer is prohibited by applicable law from excluding implied warranties, the duration of such implied warranties which

are not excludable shall be the original purchaser's lifetime. Some states do not allow the limitation on how long an implied warranty lasts, so the above

limitation on the duration of implied warranties which are not excludable, if any, may not apply to you. Some states do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation or exclusion of incidental or consequential damages may not apply to you.

Retailer neither assumes not authorizes any representative or other person to assume for it any obligation or liability other than such as is expressly set

forth herein. This limited warranty gives you speciﬁc legal rights, and you may also have other rights which vary from state to state.

NOTE: Double check your product for

the correct hole sizes.

1-3/4”

(45 mm)

1-3/8”

(35 mm)

1-9/16”

(40 mm)

2”

(51 mm)

Ø 2-1/8” (54 mm)

2-3/4” (70 mm)

2-3/8” (60 mm)

Drill a 1” (25 mm) diameter

hole at the center of the door

edge.

Fold here.

Place on the door edge.

Backset

1-3/4”

(45 mm)

1-3/8”

(35 mm)

1-9/16”

(40 mm)

2”

(51 mm)

Ø 1-1/2” (38 mm)

2-3/4” (70 mm)

2-3/8” (60 mm)

Drill a 1” (25 mm) diameter

hole at the center of the door

edge.

Fold here.

Place on the door edge.

Backset

FOR

G32-KPDA612 Rev. 16/03-00

TOLL FREE HELP LINE

1-877-ONE-LOCK

HOMEDEPOT.COM

Note : The metal connector

side should face outward.

For 2-3/8” backset: 3-7/16”

For 2-3/4” backset: 3-13/16”

Depth of latch hole

Summary of content (2 pages)

PAGE 1
G32-KPDA612 Rev. 16/03-00 3 Pre-installation (continued) – Door Preparation NOTE: If your door is pre-drilled, check the hole sizes to make sure they are the proper size. If they are the proper size, skip to the INSTALLATION section. FOR Cut out TEMPLATE (reverse page) and use to mark the door, drill holes, and chisel out the mortise. NOTE: Drill from both sides of the door to prevent wood splitting.
PAGE 2
PROGRAMMING 1 HOW TO LOCK / UNLOCK THE LOCKSET OVERVIEW OF FUNCTIONS / LOCK BUTTON ENTER 1. Red light: Represents an incorrect entry or the unit is in programming mode. 2. Yellow light: Flashes when the batteries are low in power. 3. Green light: Represents a correct entry. 4. Press to activate or lock the lockset. 1 2 3 4 5 6 7 8 9 0 OR 1 2 3 4 5 6 7 8 9 0 To lock Press “ ” to lock. Use a mechanical key to lock. OR → 1 2 3 4 5 6 7 8 9 0 1.