Instructions / Assembly
THANK YOU
We appreciate the trust and con dence you have placed in De ant
through the purchase of this backlit LCD countdown digital timer.
Visit us online to see our full line of products available for your
home improvement needs. Thank you for choosing De ant!
Installation Instructions (continued)
USE AND CARE GUIDE
BACKLIT LCD COUNTDOWN TIMER
HRS
MINS
Questions, problems, missing parts? Before returning to the store,
call De ant Customer Service
8 a.m. - 6 p.m., EST, Monday - Friday
1-866-308-3976
HomeDepot.com
Item #1000-003-076
FCC NOTE
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modi cations to this equipment. Such modi cations could
void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. This Class
B digital apparatus complies with Canadian ICES-003. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Do not use to control appliances that contain heating elements, cooking
appliances, heaters, irons, etc.
WARNING: RISK OF ELECTRIC SHOCK:
Shut off power at the fuse box or circuit breaker before
installation.
Do not use in wet locations.
For indoor use only.
WARNING: RISK OF FIRE:
Do not exceed the electrical ratings.
Only use copper wire with this device.
Do not use to control receptacles.
Do not use to control appliances that contain heating
elements, cooking appliances, heaters, irons, etc.
RATINGS
120 VAC, 60 Hz
16 A General Purpose
1250W Tungsten
½ HP Motor Load
8A Inductive/Ballast Load
Hardware Included
AA – Wire Nuts x 4 BB – Screws x 2
Product Descrption
1. Up and Down Touch Buttons: Push these buttons to program your timer
for countdown time. Holding down either the Up or Down buttons will
increase the speed of the setting and the programmed time. Push and
hold both buttons simultaneously for ve seconds to adjust the blue
backlight.
2. Master On/Off Switch: Flip the switch to
override the timer programmed countdown.
3. Ground Wire (Green): Connect to ground in
the wall box. See Installation Instructions.
4. Load Wire (Red): Connect to the load in the
wall box. See Installation Instructions.
5. Neutral Wire (White): Connect to neutral in the
wall box. See Installation Instructions.
6. Line Wire (Black): Connect to the line in the
wall box. See Installation Instructions.
Questions, problems, missing parts? Before returning to the store,
call De ant Customer Service
8 a.m. - 6 p.m., EST, Monday - Friday
1-866-308-3976
HOMEDEPOT.COM
HRS
MINS
3
4
5
6
1
2
Green
Black Line
Red
(3)
(4)
(5)
(6)
White
Neutral
Load
Ground
2
Adjusting the blue backlight on the display screen
Press and hold both the Up and Down buttons (1). The buttons will
begin to blink.
Press the Up and Down buttons (1) to adjust the blue backlight to
the desired level. This blue backlight level
setting will be what the timer display
screen will be at while the screen is not
being touched.
After 5 seconds of not pushing either the
Up or Down buttons (1), the new blue
backlight will be set into the timer and the
Up and Down buttons (1) will stop blinking.
Whenever the touchscreen of the timer is
pushed, the timer blue backlight will fully
illuminate for 5 seconds and then
return to the blue backlight setting you
have programmed.
3
Manually override the on/off setting
Flip the master On/Off switch (2) below the touchscreen to ON or
OFF for the desired setting.
□ ON will turn on the timer and start the previous setting of the
last programmed time.
□ OFF will turn off the timer and the load; the blue backlight
touchscreen will be blank.
HRS
MINS
OFF
ON
1
2
2
Powering up the timer
If you do not see the numbers on the screen, you will want to verify the
unit is wired correctly, and the unit is getting power.
Also verify that the Master On/Off Switch (2) is set to the ON position.
1
Setting the timer
Verify that the Master On/Off Switch (2) is set to the ON position. The
screen will display:
□ Hours
□ Minutes
□ Up and Down buttons (1)
□ Blue backlight will be illuminated
Press the Up and Down buttons (1) to select the time you would like
the timer to keep your device or light on. It may be set from 1 minute
to 24 hours.
□ Holding down the Up and Down buttons (1) will increase the speed
of setting the programmed time.
□ Pressing the Down button (1) when at 1 minute will automatically
go to 24 hours. Conversely, pressing the Up button (1) from 24
hours will return the timer to 1 minute.
The timer will keep your hardwired device or light on throughout the
entire countdown period and then shut off the device when it reaches
0 minutes.
The next time you push an Up and Down button (1), the timer will return
the previous setting of the last programmed time automatically.
Safety Information
1
Installing the timer into your wall box
Turn off the main power at the circuit breaker.
Remove the existing switch.
Connect the wires of the timer to the wall box as shown using the wire
nuts (AA).
□ Connect the line wire to the black wire (6) from the timer.
□ Connect the load wire to the red wire (4) from the timer.
□ Connect the ground wire to the green wire (3) from the timer.
□ Connect the neutral wire to the white wire (5) from the timer. Often
the neutral (white) wire can be found in the back of the wire box
connected with a wire nut. There may be several neutral wires
bound together. Add the neutral to all neutral wires bound together
making sure the wire nut is tight.
Ensure all wire nuts are secure. Tuck the wires into the wall box leaving
room for the timer. Using the screws (BB), mount the timer to the wall
box being careful not to crush any wires.
Reinstall your wall plate so that the touch faceplate and master on/off
switch of the timer is visible.
Turn the main power on at the circuit breaker.
Installation Instructions
Black (6)
L (out)
Load
White (5)
Red (4)
Line
Ground
Green (3)
Timer
L (in)
N
HRS
MINS
OFF
ON
2
HRS
MINS
OFF
ON
1
HRS
MINS
OFF
ON
2
Operating Instructions