Instructions / Assembly
THANK YOU
We appreciate the trust and con dence you have placed in
De ant through the purchase of this push button countdown
timer. Visit us online to see our full line of products available for
your home improvement needs. Thank you for choosing De ant!
USE AND CARE GUIDE
PUSH BUTTON COUNTDOWN TIMER
5 Min
15 Min
60 Min
30 Min
2 Hour
4 Hour
Questions, problems, missing parts? Before returning to the store,
call De ant Customer Service
8 a.m. - 6 p.m., EST, Monday - Friday
1-866-308-3976
HomeDepot.com
Item #460-974
Safety Information
FCC NOTE
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modi cations to this equipment. Such modi cations could
void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. This Class
B digital apparatus complies with Canadian ICES-003. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Installation Instructions
1
Installing the timer
Disconnect the power at the fuse box or circuit breaker.
Remove the wall plate and existing single pole switch, if applicable.
Strip at least 3/8 in. of insulation from the ends of the building
wires.
Connect the wires using the provided wire nuts (AA) (use with
copper wire only):
□ Connect the BLACK wire to the circuit’s (HOT) line wire.
□ Connect the RED wire to the circuit’s load wire.
□ Connect the GREEN wire to the ground wire.
Tuck the wires into the box, leaving enough room for the timer, and
mount the timer securely into the box using the screws (BB) provided.
Carefully screw the provided wall plate into place. You may use any
Décora style wall plate with this timer.
Restore power at fuse box or circuit breaker.
NOTE: The timer will not function until it is fully charged. Once
power is restored, it will take about 1 minute to fully charge, and
the 5 minute light will ash.
NOTE: The load may be powered on when power is restored
from the circuit breaker. The power will automatically turn off
once the unit is charged.
Operating Instructions
1
Using the timer
Press the appropriate button on the timing pad (1) for the amount
of time you wish the lights or device to be powered on. The blue
LED will blink.
Select a new time, or press the function button (2) to turn the lights
or device on for the duration of the last timing pad (1) entry.
NOTE: Hold the function button (2) for ve seconds to turn the
lights or device on inde nitely. Press once more to turn off.
Troubleshooting
WARNING: RISK OF ELECTRIC SHOCK:
Shut off the power at the fuse box or circuit breaker before
installation
Do not use in wet locations
Use indoors only
WARNING: RISK OF ELECTRIC FIRE:
Do not use to control appliances that contain heating
elements such as cooking appliances, heaters, and irons
Do not exceed electrical ratings
Use only copper wire with this device
RATINGS
125 VAC, 60 Hz
800W Tungsten
800 VA Ballast
6.4 A Resistive
1/4 HP
Hardware Included
AA - Wire Nut x3 BB - Screw x2
Problem Solution
The timer lights never ash. Check the wiring. The ground wire must be
grounded properly.
The device or light which the timer
controls turns on when the breaker
was initially turned on.
This is normal. The device or light will turn
off after 1 minute.
The timer freezes and does not
respond to button commands.
This happens if you cycle the load too many
times in a short period. Wait one minute and
the timer will be ready for use.
Questions, problems, missing parts? Before returning to the
store, call De ant Customer Service
8 a.m. - 6 p.m., EST, Monday - Friday
1-866-308-3976
HOMEDEPOT.COM
Product Description
5 Min
15 Min
60 Min
30 Min
2 Hour
4 Hour
1
2
1. Timing pad: Press the appropriate time button to select a time for the
lights or device to stay on (5 Min.-4 Hr.).
2. Function button: Press once to turn the lights or device on for the
duration of the last timing pad entry. Hold for ve seconds to turn the
lights or device on inde nitely. Press once more to turn off.
5 Min
15 Min
60 Min
30 Min
2 Hour
4 Hour
1
2
Green Ground
Black Line
Red Load
Ground
White
White
Red
Black
Load
Green
Timer
Black
= Wiring Nut
Line