Defi-Link Display VSD CONCEPT Operation Manual Nippon Seiki Co., Ltd.
Before Installation(for installation personnel) Warning ● ●Carefully consider the installation location and driver's operation of the product before installation. Be sure not to install the unit where it could fall. Improper installation or operation could cause the product to fall and damage the vehicle or cause serious danger by impeding driving. ●Do not disassemble or modify this product. Such actions can not only damage or destroy the product but will also void the warranty.
Installation (for installation personnel) Warning ●Carefully read the "Before Installation" and "About Installation and Operation" sections of the manual concerning installation and operation. Then install the product properly and safely. Installation in an unsuitable location or improper installation can result in the product falling from its position or damage to the vehicle. Caution ●When installing the display, be sure to follow the instructions for Defi-Link Control Unit II(or Defi-Link Control Unit).
■When When the Defi-Link Display VSD CONCEPT is used WITH a connection to the Defi-Link System ※These procedures are applicable on condition that Defi-Link Control Unit II(or Defi-Link Control Unit) and the power supply wire have been installed. Defi-Link Display VSD CONCEPT and Defi-Link System Wiring Diagram Display Film Defi-Link Meter BF Defi-Link Display METER OUTPUT2 DIM sensor Defi-Link Display VSD CONCEPT Display unit Speed & Tacho signal wire ※Do not connect the blue wire(tacho signal).
STEP２ Check Wiring １：Connect the display wire of Defi-Link Display VSD CONCEPT to DISPLAY UNIT of D.C.Unit. ２：Check that all the wires are properly connected. ３：Turn on the ignition of vehicle and make sure the display is lighted.（The display looks inverted on the display unit.） ４：If the display is lighted, go to the next step. If not, go back to STEP1(WIRING) and rewire. STEP３ Applying the Display Film Warning ●Display must be projected on the bottom 5in(130mm) of the windshield.
STEP４ Installation of Display Unit and DIM Sensor Warning ●Improper installation could cause the product to fall and damage the vehicle or cause serious danger by impeding driving. ・Attach the display unit in a location which will not hinder driving. ・Make sure that both the display unit and D.C.Unit are firmly attached. Confirmation ●When leaving car under the direct sunlight, cover the display unit with a white cloth. It prevents the unit from deterioration.
Trouble Shooting(for customer and installation personnel) Warning ●If operation of the product seems unusual, inspect the product to confirm that there is no malfunction. If an operational problem has occurred, it could result in an accident. ※In addition to a general inspection of the product, use the following table to confirm proper operation of the unit. If the operational problem does not appear in the following table, contact the installation personnel. Condition ○Does not display.
Operation(for customer) 1.Set-Up Mode(Screen for setting units and display data parameters) Confirmation n ●Be sure to make preparatory settings. The unit will not operate properly without settings being made. ●Set up while the vehicle is stopped. When changing the factory settings shown below, pressing the SET UP(ENTER) button for more than 2 seconds after the opening mode has completed will bring up the setting mode for units.
Pulse free setting Hold Speed pulse setting Press ENTER button while the vehicle is moving at 60km/h or 40MPH. NOTE: The pulse free setting needs to be done again if units are changed. ③Setting of Number of Cylinders Press ENTER button when the following figure is displayed. Use SELECT/BAR SELECT button to select the number of cylinders, then press ENTER button to set the selection. ３ ４ ５ ６ ８ Number of cylinders setting Set 2 rotary engine at 4 cylinders and 3 rotary engine at 6 cylinders.
⑥Setting of Tachometer Warning Press ENTER button when the following figure is displayed. Green LED is lighted up. Use SELECT/BAR SELECT button to set the desired warning1 value. Press ENTER again. Green and red LEDs are lighted up. Use SELECT/BAR SELECT button to set the desired warning2 value. If SELECT/BAR SELECT button is pressed and held, the number is fast-forwarded.
⑨Setting of Auto Warning Press ENTER button when the following figure is displayed. Use SELECT/BAR SELECT button to select ON or OFF of the auto warning function. Auto warning setting NOTE: This function operates when the Defi-Link Display VSD CONCEPT is linked with the Defi-Link System. ⑩Setting of Illumination Control Press ENTER button when the following figure is displayed. Use SELECT/BAR SELECT button to select auto or manual of the dim control mode.
２. Opening and Ending Mode Opening and ending modes are performed after the ignition key is turned on and off. Opening mode Ending mode ３. Operation Mode Illumination control When the auto dimmer mode is selected in the setting of illumination control, the brightness of display is adjusted automatically depending on the outside light. The brightness can be selected from three stages by pressing the DIM(ENTER) button. When the manual dimmer mode is selected, the brightness of display is fixed.
■When When the Defi-Link Display VSD CONCEPT is used WITH a connection to the Defi-Link System ※For operations ① through ⑨ shown below, refer to the Operation Manual for Defi-Link Control Unit II(or DefiLink Control Unit. ①Real Mode The actual data on current speed, engine speed, oil pressure, fuel pressure, oil temperature, water temperature, and exhaust temperature is displayed in this mode.
⑤Warning Set Mode Engine Speed Oil Temp. Boost ※Examples of display Pressing the WARN SET button of Defi-Link Control Unit II(or pressing the SELECT button of Defi-Link Control Unit) will bring up Warning Set Mode. To set the warning value, please refer to the operations manual of Defi-Link Control Unit II(or Defi-Link Control Unit).
⑧Rec Mode When the vehicle is moving at the speed of 1km/h(1MPH) or more, connected sensor data and the speed data are recorded for a maximum of 3 minutes by pressing the REC button of Defi-Link Control Unit II(or Defi-Link Control Unit). "R" is displayed during recording. Data displayed in the digital and bar display section can be changed by pressing SELECT/BAR SELECT button.
Simplified Set-up Chart SET: Setting of units "kPa, ℃, km/h" or "PSI, ° F, MPH" SPEED SET: Setting of speed pulse PULSE-4: Select the proper speed pulse from 2, 4, 8, and 16. FREE: Set speed pulse other than 2, 4, 8, or 16. TACHO-SET: Setting of number of cylinders ENGINE-4: Select the proper number of cylinders from 3, 4, 5, 6, and 8. WARM-UP: Setting of warm-up function SPECIAL: Choose ON or OFF of special display.
