Specifications
T
O
R
Q
U
E
W
R
E
N
C
H
SETTINGS
El
.
TRANSFER GEARBOX
LT230T
-
4
cylinder Petrol
and
Diesel engine
and
V8
(cont.)
Cross shaft housing to front output housing
................
Gcar change
.......................................................
Gear change
........................................................
Connecting rod ...................................................
Cross
shaft to highAow lever
...................................
Pivot shaft to
link
arm
...........................................
Anti
-
rotation plate intermediate shaft .......................
Front output housing cover
....................................
Pivot bracket to extension housing
...........................
Finger housing to front output housing
......................
Mainshaft bearing housing to transfer case
.................
Brake drum
to
coupling flange
................................
Gearbox to transfer case
...............
Gearbox to transfer case ........................................
End cover bearing housing to transfer case
.................
Speedometer housing to transfer
.............................
Speedometer housing to transfer
.............................
Selector finger
to
cross shaft (highhow)
.....................
Selector fork high/low to shaft
.................................
Transmission brake to speedometer housing ..............
Gearbox to transfer case
........................................
Oil
drain plug
......................................................
Transfer case assembly .............. ..............
Detent plug
........................................................
Differential casings ..............................................
Front and rear out flange
.......................................
Differential case rear
............................................
Oil filler and level plug transfer
...............................
Transfer breather
.................................................
Inter shaft stake nut
..............................................
Nm
lbf
ft
22
.
28
22
.
28
22
.
28
22
.
28
22
.
28
22
.
28
22
.
28
22
.
28
22
.
28
22
.
28
22
.
28
22
.
28
40
.
50
40
.
50
40
.
50
40
.
50
40
.
50
22
.
28
22
.
28
65
.
80
40
.
50
16
.
21
16
.
21
16
.
21
16
.
21
16
.
21
16
.
21
16
.
21
16
.
21
16
.
21
16
.
21
16
.
21
16
.
21
29
.
37
29
.
37
29
.
37
29
.
37
29
.
37
16
.
21
16
.
21
48
.
59
29
.
37
See note
Plug to be coated with Hylomar and peened
.
Screw plug fully in (spring solid) then turn two
complete turns back
.
25
.
35
19
.
26
55
.
64
146
.
179
66
.
80
25
.
35
7-
11
5
-
8
130
.
140
40
.
47
108
.
132
50
.
59
19
.
26
96
.
104
NOTE:-
Studs to be assembled into casings with sufficient torque to wind them fully home. but this torque must
not
exceed the maximum figure quoted for the associated nut on final assembly .
GEARBOX
AND
TRANSFER BOX LT95
.
V8
Petrol engine
Bell housing to cylinder block bolts
..........................
Gearbox casing to bell housing
2
off
.........................
Gearbox casing
to
bell housing 2
off
.........................
Gearbox casing
to
bcll housing stud and nuts
..............
36, 6
.
44, 8
1463
.
179
85, 4
.
104, 4
Gearbox casing to bell housing nuts
..........................
85, 4
.
104, 4
146,
5
.
179
Output flange
-
rear
-
nut and bolts ....................... 43, 4
.
513
Output shaft
-
rear
-
nut
.....................................
146,
5
.
179
Output shaft
-
front
-
nut .................................... 146,
5
.
179
Gear selector spherical scat bolts
.............................
13, 6
.
16, 3
43, 4
.
51,
5
9, 9
.
11, 9
Propeller shaft
to
flange bolts
.................................
All other
nuts
and bolts:
M6
................................................................
M8
................................................................
23:7
.
29.7
M10
...............................................................
48
.
58
27
.
33
108
.
132
63
.
77
63
.
77
108
.
132
32
.
38
108
.
132
108
.
132
10- 12
32
.
38
7.3
.
8.7
17.5
.
21.3
35.4
.
42.8
5