20 BRIDGE INSTALLATION: SIM CARD Insert SIM card in this slot. SIM support@reconeyez.
1 BRIDGE INSTALLATION: SIM CARD Whereas the SIM card that is used in the Handheld device depends on the smartphone or tablet, Bridge SIM card is always standard-sized large SIM. support@reconeyez.
BRIDGE INSTALLATION: CONF. After the SIM card has been inserted it is necessary to configure the correct APN and Server address for the Bridge with the Handheld. Please use the Handheld device to find the Bridge and change the APN and Server address in the Bridge Configurable parameters menu. Please refer to Handheld manual for more detailed instructions on different parameters. support@reconeyez.
23 BRIDGE INSTALLATION: CONF. Please measure GSM signal quality in the installation area with the ReconEyez app in the Handheld before installation of devices. Mobile RSSI in Bridge Configurable parameters menu displays the GSM signal quality usually from -100 (min) to -20 (max) dBm. For good alarm traffic any GSM signal under -100 dBm is acceptable for the Reconeyez system. support@reconeyez.
24 BRIDGE INSTALLATION: CONNECTIVITY TEST After configuration, Bridge should have first connectivity test. There are two ways to do this: 1) Please insert all 4 batteries into the Bridge and make a Theft alarm (shake the Bridge a few times). Please check the Command Center User Interface (UI) if the corresponding Bridge sent a Theft alarm to UI. Repeat if necessary. support@reconeyez.com The image above shows how a Theft alarm appears in UI.
25 BRIDGE INSTALLATION: CONNECTIVITY TEST After configuration, Bridge should have first connectivity test. There are two ways to do this: 2) Use the Handheld, go to Bridge – Configurable parameters, make a Theft alarm, press Refresh in Configurable parameters menu, see if the 3G/GSM RSSI displays signal strength in dBm (-20 to -100). If it does, then Bridge has connectivity with server. support@reconeyez.
26 BRIDGE INSTALLATION 1. Always perform Bridge connectivity test as first step in each installation location after entering all 4 batteries! The image above shows how a Theft alarm appears in UI. support@reconeyez.
27 BRIDGE INSTALLATION 2. Find a suitable place to install the Bridge. In areas with poor GSM coverage the Bridge should be installed at an elevated position! Bridge should be installed: •on an elevated position (for better GSM / 2,4 GHz radio coverage and camouflage) •with minimal possible distance from all adjacent Detectors •with preferable direct line of sight with all Detectors (or minimal obstructions); •NOT near powerful electric currents/gadgets; •NOT surrounded by radio blocking materials (e.g.
28 BRIDGE INSTALLATION Avoid radio-wave obstacles near the Bridge! The Bridge must have good access to GSM/Mobile network. Avoid close proximity of walls, metal objects, electric devices, don't install underground or in cavities. Install in elevated position in regions with low GSM/Mobile coverage. support@reconeyez.
29 BRIDGE INSTALLATION 3. First install the fastening unit (screw, plate) to the surface. Use the Tx 30 key to fix a fastening-screw and cable-ties to fix a fastening-plate. Tx 30 key Final position support@reconeyez.
30 BRIDGE INSTALLATION The correct position of the Bridge is vertical, as shown on the photo – the 2,4 GHz antenna pointed downwards. Due to Bridge omnidirectional antennas it is not advised to install Detectors directly above or below the Bridge! Always insert all 4 batteries to make Bridge hermetic and avoid water damage to the inside of the Bridge! support@reconeyez.
31 BRIDGE INSTALLATION 4. Use the 8 mm hex key to fasten the Bridge on the fastening screw/fastening plate/mast. Rest the lower end of the Bridge onto the surface if possible. 8 mm hex key support@reconeyez.
32 BRIDGE INSTALLATION 5. Always make sure to enter all 4 batteries - without all 4 batteries Bridge is not waterproof! Check that each battery has 2 rubber seals in tact and fasten them with nut/security nut. Bridge is now ready to receive alarms. support@reconeyez.
DETECTOR INSTALLATION support@reconeyez.
DETECTOR INSTALLATION 1. Find a suitable place for the Detector to cover the chosen hotspot or gap. The best alarm speed will be achieved with direct line of sight between the Detector and the Bridge. support@reconeyez.
DETECTOR INSTALLATION 2. Make sure that there are no small branches or leaves in 150 degree and 3 meter radius of the Detector that may cause false alarms and IR flash overexposure in night photos. Try to avoid larger moving objects (e.g. large bushes moving in the wind) in the detection area of 30 meters. Use appropriate tools to clean branches and plants in front of the Detector.
DETECTOR INSTALLATION 3. Ensure that the field of view of the Detector covers the desired hotspot correctly! Place the Detector diagonally towards the movement path to ensure that the moving person or object is in the field of view for longer time and at least half-profile is captured. Check that the desired hotspot is on the Alarm photo through Handheld or Reconeyez Web UI. support@reconeyez.
DETECTOR INSTALLATION 4. Install the Detector on a stable surface. Avoid thin trees/posts that can move. This helps to prevent false alarms due to wind or passing traffic vibrations. support@reconeyez.
DETECTOR INSTALLATION 5. Put in place the fastening unit (screw, plate). Use the Tx 30 key for a fastening screw and screws/cable-ties for fastening plate. Use the 8 mm hex key to fasten the Detector with the correct downward angle to the fastening unit (pole, screw or plate). Installation pole Fastening screw Fastening plate support@reconeyez.
DETECTOR INSTALLATION 6. Insert the battery last to avoid nuisance alarms. It is recommended to install the battery after all other installation works have been done. This reduces the number of nuisance alarms caused by the movement in the detection area during installation process. Circa 30 seconds after batteries have been entered the Detector is ready to send alarms to Command Center. support@reconeyez.
DETECTOR INSTALLATION 7. When batteries inserted perform a Trace to check signal from detector to Bridge. Trace enables to measure 2,4 GHz signal between the detector and bridge in real time. This is a vital tool during installation. Trace function must be enabled from Settings menu of ReconEyez before use. support@reconeyez.
41 DETECTOR INSTALLATION 8. Use the ReconEyez application on the Handheld device to request a test photo from the Detector. This helps to check if the Detector PIR sensor is covering the desired areas. Please refer to Handheld manual for more detailed instructions if necessary. Selecting Show alarm area in Handheld displays the movement detection area of the PIR sensor on the alarm photo. This is a vital tool in the installation process of Detectors. 2,4 ГГц antenna support@reconeyez.
42 DETECTOR INSTALLATION After batteries have been inserted then it is critical to check the field of view of detector with Handheld device. - make sure that the centermost PIR sensor zones are pointing at the mid-section of potential intruder at desired maximum distance - for example stand at 25-30 meter distance with Handheld and adjust detector angle so the centermost squares would point at your mid-section. support@reconeyez.
DETECTION AREA PIR SENSOR DETECTION ZONES ON AN ALARM PHOTO. support@reconeyez.
DETECTION AREA 44 Detector PIR sensor coverage, side view. Ideal installation height in case of flat ground is 2,1 meters with detector downward angle of 12 degrees. support@reconeyez.
45 DETECTION AREA 20 meter meter zone coverage in case of correct installation angle Detector tilt 12 degrees down if flat ground 30 meter zone coverage in case of correct installation angle Default installation height 2,1 meters Movement sensor detection distance 30 meters Detector PIR sensor coverage zones. support@reconeyez.
DETECTION AREA Detector PIR sensor coverage, view from above support@reconeyez.
CORRECT INSTALLATION support@reconeyez.
CORRECT INSTALLATION support@reconeyez.
CORRECT INSTALLATION support@reconeyez.
CORRECT INSTALLATION support@reconeyez.
CORRECT INSTALLATION support@reconeyez.
CORRECT INSTALLATION DAY PHOTO: PIR zones on day photo support@reconeyez.
INCORRECT INSTALLATION BRANCHES TOO CLOSE TO THE DETECTOR. support@reconeyez.
INCORRECT INSTALLATION 54 NIGHT PHOTO: FLASH OVEREXPOSURE ON CLOSE OBJECTS Don’t put large objects in front of detectors closer than 3-5 meters, it may impact detector and AI performance. support@reconeyez.
55 POST INSTALLATION CHANGES IN VIEW NIGHT PHOTO: FLASH OVEREXPOSURE ON CLOSE OBJECTS IF LARGE ITEMS SUCH AS MACHINERY , SKIPS ETC ARE PLACED DIRECTLY IN FRONT OF DETECTORS AT SHORT RANGE AFTER INSTALLATION THIS CAN LEAD TO HIGH LEVELS OF REFLECTION AT NIGHTTIME AND PARTIAL VISIBILITY OF ’ACTORS’. THIS CAN IMPACT THE ABILITY OF THE AI TO RECOGNISE PEOPLE AND VEHICLES AND MAY MEAN MISSED ALARMS. IF HAPPENS ON-SITE WARN YOUR CLIENT !!! support@reconeyez.
INCORRECT INSTALLATION NIGHT PHOTO: PIR zones on night photo support@reconeyez.
Thank you! support@reconeyez.
