DBOARD R3 Technical Operation Manual BY APPROV. REV.
INDEX 1. Introduction ............................................................................................................................................. 4 1.1. 2. Glossary ........................................................................................................................................... 4 Safety information ................................................................................................................................... 4 2.1.
BY APPROV. REV. DATE REASON OF ISSUE DEEPTRACK DEEPTRACK A1 02/2020 DOCUMENT CREATION BF BF A2 09/2020 MARKINGS UPDATE BF BF A3 10/2020 FCC/ISED Regulatory notices This document and the information in it are provided in confidence, for the sole purpose of exploring business opportunities between the disclosing party and the receiving party. Confidential document.
1. Introduction The purpose of this manual is to describe the main characteristics, installation and operation procedures for the DBOARD R3 Tracker Controller. It is required that the Installer adheres to these instructions to ensure correct installation. For an in depth understanding detailed manuals for each of the main components are available. 1.1. Glossary Term Tracker (or Solar Tracker) DBOARD Emergency Stop 2.
2.5 Radio Frequency (RF) Safety Due to the possibility of radio frequency (RF) interference, it is important that you follow all the special regulations that may apply regarding the use of radio equipment. Follow the safety advice given below. Operating your device close to other electronic equipment may cause interference if the equipment is inadequately protected. Observe any warning signs and manufacturer’s recommendations. 2.
3. DBOARD overview FRONT VIEW BACK VIEW This document and the information in it are provided in confidence, for the sole purpose of exploring business opportunities between the disclosing party and the receiving party. Confidential document. It is not allowed to reproduce or disclose partial or totally the information contained in it, except by express written consent of Deeptrack.
3.1. Connectors and signals - Interfaces This document and the information in it are provided in confidence, for the sole purpose of exploring business opportunities between the disclosing party and the receiving party. Confidential document. It is not allowed to reproduce or disclose partial or totally the information contained in it, except by express written consent of Deeptrack.
1. LoRa interface: LoRa embedded Antenna and footprint for external antenna connector (UMC) Through the LoRa antenna interface, the user can communicate LoRa devices. The board includes an optional connector for install an external antenna. The current and certified antenna is omnidirectional and lineally polarized. 2.
6. RS485 connector (B6): RS485 interface. Connector PTSM 0,5/ 3-HV-2,5. For devices which does not need power from the board and are powered from another voltage source. Signals: o o o 7. P GND N RS485 connector (B4/B5): RS485 interfaces. Connectors PTSM 0,5/ 5-HV-2,5. For devices which can be 24VDC powered from the board. Signals: o o o o o 8. 24V GND P (D+) N (D-) PE Digital IO connector: Digital IO, 2 inputs, 1 SSR output. Connector PTSM 0,5/ 5-HV-2,5. Signals: o o o o o 9.
Signals: • • • • • • S1 S0 SCK nCS GND 3V3 11. Capacitive buttons: are used to interact with a human user 12. Reset button (S2): Directly connected to the reset pin of the microcontroller, it is not programmable. 13. Optional buzzer (GPIO) 14. Accelerometer IIS3DHHC 15. Footprint for I2C port This document and the information in it are provided in confidence, for the sole purpose of exploring business opportunities between the disclosing party and the receiving party. Confidential document.
4. Installation instructions 4.1. Power the DBOARD WARNING The board should not be connected while the power supply is on. The DBOARD is powered through one SPT 2.5/4-V-5.0 connector in the left lower part of the board. 24VDC powered, this power supply may come from an AC/DC converter, battery, DC/DC converter, etc. Mostly of the power supply will work with the DBOARD, but the condensers in the input may be considered.
7. Markings Commercial brand and manufacturer info. Commercial brand of manufacturer (DEEPTRACK) is included, along as official address of the company. The name of the equipment (DBOARD R3) is also included along with input power supply. Additional information regarding documentation can be found in this part of the marking CE Marking The device also complies CE regulation son CE marking is also included FCC & IC IDs Regulatory Notice “This device complies with part 15 of the FCC Rules.
8. FCC/ISED Regulatory notices Modification statement DEEPTRACK S.L.U. has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user’s authority to operate the equipment. DEEPTRACK S.L.U. n’approuve aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature. Tout changement ou modification peuvent annuler le droit d’utilisation de l’appareil par l’utilisateur.
