Before returning this product to the store of purchase Contact Dee Zee if you experience the following problems: • Missing Parts • Installation Problems/Questions • Warranty Questions 1.800.779.2102 Hours of operation: 8am - 5pm CST, Mon-Friday Review complete warranty policy and register your product at: www.deezee.
Dee Zee Running Board Installation Instructions Congratulations on your purchase of a quality Dee Zee product. Dee Zee is recognized as having the highest quality running boards and accessories on the market today. We have earned this reputation by offering our customers a product they can be proud to place on their vehicles. Dee Zee meets all the criteria of manufacturing a custom-fit product which guarantees it to be the easiest product to install.
Dee Zee Britetread Running Board Installation Instruction DZ 2041 (2004 - Current) Ford F150 Super Cab Pickup A Britetread Running Board B X2 Britetread Mudflap C Rocker Panel Bracket X2 H G D X6 X12 X16 M 1/4 x 1” Sheet Metal Screw 8mm x 25mm Hex Head Bolt X4 X12 1/4 x 3/4” Hex Head Bolt F K X12 1/4“ Flat Washer X4 X6 X24 X20 L 5/16“ Flat Washer 3/8“ Hex Nut P N E J I 1/4 x 1” Ribneck 3/8 x 1“ Hex Carriage Head Head Bolt Bolt 1/4“ Hex Nut Running Board Bracket 3/8" Loc
1 Secure britetread mudflap (B) to britetread running board (A) using 1/4 x 3/4” hex head bolts (E), 1/4” flat washers (F), and 1/4” hex nuts (G). Tighten into place using a 7/16” wrench / or socket. Place bulb-seal gasket (Q) onto the backlip of britetread running board (A) and trim flush with the britetread mudflap (B) and the end of britetread running board (A).
2 You will need to remove the black tape from the rocker panel and then place an 8mm u-clip (P) into the hole locations shown below.
3 Slide 8mm u-clip (P) onto the rocker panel bracket (C) as shown below. Make sure that the hole in 8mm u-clip (O) is aligned with the hole in rocker panel bracket (C). Diapositive l'u-agrafe de 8mm (p) sur la parenthèse de panneau de culbuteur (c) comme montré ci-dessous. Assurez-vous que le trou dans l'u-agrafe de 8mm (o) est aligné avec le trou dans la parenthèse de panneau de culbuteur (c).
4 Front and Rear Brace Installation Place the rocker panel bracket (C) up to the vehicle rocker panel and u-clip (p) and secure into place using an 8mm x 30mm flange head bolt (N) as shown below. 13mm Wrench or Socket Placez la parenthèse de panneau de culbuteur (c) jusqu'au panneau de culbuteur de véhicule et à l'u-agrafe (p) et la fixez dans l'endroit à l'aide d'un boulon de tête de bride de 8mm x de 30mm (n) comme montré ci-dessous.
5 Front and Rear Brace Installation Secure the 8mm u-clip in the bottom flange on rocker panel bracket (C) to the rocker panel using 8mm x 25mm flange head bolt (N). Asegure el u-clip de 8m m en el reborde inferior en el soporte del panel del eje de balancín (c) al panel del eje de balancín usando el perno de la cabeza del reborde de 8m m x de 25m m (n).
6 Using the drawing below as a guide, place running board bracket (D) up to rocker panel bracket (C). Secure the rear-top hole in running board bracket (D) to the hole in the rocker panel bracket (C) using 3/8 x 1" hex head bolt (I), 5/16" flat washers (J), 3/8" lock washer (L), and 3/8" hex nut (K). Note: See drawings below for correct hole identification.
7 Rotate the running board bracket (D) to the upright position and secure it into place using a 3/8 x 1" hex head bolt (I), 3/8" lock washer (L), 3/8" flat washers (J), and 3/8" hex nuts (K) as shown below. Rote el soporte corriente del tablero (d) a la posición vertical y asegúrelo en lugar usando un perno de la cabeza de la tuerca hexagonal de 3/8 del x 1"(i), la arandela de cerradura del 3/8" (l), las arandelas planas del 3/8"(j), y las tuercas de tuerca hexagonal del 3/8" (k) según lo demostrado abajo.
8 Place britetread running board (A) up to the running board brackets (D) as shown below. Slide the britetread running board up to the rocker panel so that it is flush with the vehicle rocker panel. Placez le panneau courant de britetread (a) jusqu'aux parenthèses de panneau de fonctionnement (d) comme montré ci-dessous. Glissez le panneau courant de britetread jusqu'au panneau de culbuteur de sorte qu'il soit affleurant du panneau de culbuteur de véhicule.
9 Using the bottom holes in the running board bracket (D) as a guide, drill 1/4” holes through the britetread running board. Secure the running board bracket (D) to the britetread running board using 1/4 x 1” ribneck carriage head bolts (H), 1/4” flat washers (F), and 1/4” hex nuts (G). Tighten into place using a Drill with a 7/16” wrench / or socket. 1/4” drillbit En utilisant les trous de bas dans le panneau courant encadrez (d) comme guide, forent des trous de 1/4"par le panneau courant de britetread.
10 Drill two holes through the britetread mudflap and the sheet metal of the vehicle wheel well opening. Secure the britetread mudflap to the vehicle wheel well opening using 1/4 x 1” sheet metal screws (M). Tighten into place using a 3/8” wrench / or socket. Drill with a 3/16” drillbit Forez deux trous par le mudflap de britetread et le métal de feuille de l'ouverture 3/8“ Wrench de soute de train de véhicule.
