Use and Care Guide

Continued
NOTE: Bar & Table Top Epoxy is VOC-Free. We do not have FDA approval certifying direct, long-term contact with food, however once epoxy is
fully cured for 30 days, it is an inert plastic and should be fine for incidental exposure to food. It is not antimicrobial. Epoxy is not safe to ingest
(liquid or cured). Do not cut on or prepare raw food on epoxy surfaces.
This information is provided in good faith and correct to the best of our knowledge and should be verified by the end user, as is the suitability of
the material for their application. No warranty, guarantee, or representation is made as to the sufficiency of the information for the safe use of the
product, nor to relieve the end user of any Federal, State, or Local regulatory responsibility. The Limited Warranty of this material shall be limited to the
replacement of defective material.
At WiseBond™, (A division of DeckWise
®
, The Ipe Clip
®
Fastener Company, LLC, we are dedicated to providing our customers with the tools necessary
for success. From custom product development to exceptional technical and customer service. Order online anytime at www.WiseBond.com or contact
us with any questions at 1-866-427-2547.
• One of the best things about this product is the ease
with which it can be re-coated after a period of time.
Even a well-worn, scratched surface can be lightly
sanded and recoated with fresh material to be returned
to its original luster.
• This product has excellent UV resistance, but all epoxy
products will eventually begin to yellow under sunlight.
This includes the curing agent side resin, as well as the
finished cured products.
• Clean Up Procedure: Tools can be cleaned with
isopropyl alcohol 99%, or a residue-free cleaner.
Do not use soap and water.
SUPER WET GLOSS!
USE & CARE SPECIFICATIONS
Bar & Table Top Epoxy 1:1 Ratio
1-866-427-2547 | [e-mail] | www.WiseBond.com
WiseBond
™
is a Division of DeckWise
®
, The Ipe Clip
®
Fastener Company, LLC • 2111 58th Ave. East, Bradenton, FL 34203
All rights reserved. ©Copyright 2019
Rev:7/16/2019
Coverage Volume Based on 1/8" Thick Pour:
Use the Coverage Table to determine the volume of mixed resin you will
need. Coverage is 12 sq.ft. at 1/8" thick per combined gallon. These epoxy
calculations are either/or for the table seal coat and larger flood coat.
Example: 1-gallon of epoxy will cover either 12 sq.ft. for a flood coat or 36
sq.ft. for a seal coat, not both. Remember that this is not an exact science,
as the amount of resin allowed to run off the project will vary by user.
It is always better to mix too much rather than too little resin to ensure
completion of your project.
CAUTION!
• Do not expose the product to direct sunlight.
• Keep container closed to prevent contamination.
• May cause eye and skin irritation. Use this
product only in a well-ventilated area with
protective gloves and eye protection.
• Do not eat, drink, or smoke when using this
product.
• When mixed together in mass this material can
generate excessive heat, handle with caution.
• Dispose of containers and contents in accordance
with all Federal, State, and Local regulations.
(Refer to SDS for detailed safety information)
Sq. Ft. Coverage Volume by
Thickness of Pour
Measured in Inches and Square Feet
The figures below will vary depending
upon desired thickness
Desired Thickness Per 1.5-Gal Kit
1/4" 6 sq. ft.
1/8" 12 sq. ft.
1/16" 24 sq. ft.
1/32" 48 sq. ft.
1/64" 96 sq. ft.
Coverage below is at 1/8" thick
1 Gallon
12 sq. ft.
3 Gallons
36 sq. ft.
5 Gallons
60 sq. ft.
7 Gallons
84 sq. ft.
2 Gallons
24 sq. ft.
4 Gallons
48 sq. ft.
6 Gallons
72 sq. ft.
8 Gallons
96 sq. ft.