99643561_A_ML.
99643561_A_ML.qxp 30/08/2007 13:53 Page 74 FR 02 Dear Customer, DA 26 You have purchased a DE DIETRICH oven and we would like to say thank you. DE 50 EN 74 ES 98 IT 122 NL 146 PT 170 Our research teams have designed a new generation of appliances for you, which, thanks to their quality, esthetics and technological advances have resulted in exceptional products, a testament to our know-how.
99643561_A_ML.
99643561_A_ML.qxp EN 30/08/2007 13:53 Page 76 1 / INFORMATION FOR THE USER Warning sufficiently ventilated. You may notice a particular odour, or a small release of smoke. All of this is normal. — During cooking, ensure that the door of your oven is completely closed so that the seal can do its job properly. — When in use, the appliance becomes hot. Do not touch the heating elements located inside the oven. In doing so, you would run the risk of suffering serious burns.
99643561_A_ML.qxp 30/08/2007 13:53 Page 77 1 / INFORMATION FOR THE USER EN — Never use steam or high-pressure devices to clean the oven (requirement imposed by electrical safety concerns). — For your safety, your oven is equipped with an AUTOMATIC STOP, if you forget to turn off your oven by mistake. After 23-and-a-half hours of operation, the AS (Automatic Stop) feature is activated and your oven stops running.
99643561_A_ML.qxp 13:53 Page 78 2 / INSTALLING YOUR APPLIANCE 50 10 20 50 EN 30/08/2007 555 376 388 595 560-568 550 min i 550 mini 380 536 380 22 400 560-568 310 fig.1 • CHOICE OF LOCATION • FITTING To do this: 1) Remove the rubber screw covers to access the mounting holes. 2) Drill a Ø 2 mm hole in the cabinet panel to avoid splitting the wood. 3) Attach the oven with the two screws.
99643561_A_ML.qxp 30/08/2007 13:53 Page 79 EN 2 / INSTALLING YOUR APPLIANCE Single-phase 20A Counter 220-240V~ 50Hz 220-240 V ~ Single-phase line 16A fuse or differential circuit breaker Electrical outlet 2 prong receptacle + earth CEI Standard 60083 Power supply cable length 1.50 m approx. • ELECTRIC CONNECTION Electrical safety must be provided by a correct build-in.
99643561_A_ML.qxp EN 30/08/2007 13:53 Page 80 2 / INSTALLING YOUR APPLIANCE Warning We cannot be held responsible for any accident or incident resulting from nonexistent, defective or incorrect earthing. If the electrical installation in your residence requires any changes in order to hook up your appliance, call upon a professional electrician. If the oven malfunctions in any way, unplug the appliance or remove the fuse corresponding to the sector where the oven is hooked up.
9643561_A_ML.qxp 30/08/2007 13:53 Page 81 EN 3 / DESCRIPTION OF YOUR APPLIANCE • INTRODUCTION TO YOUR OVEN A B C D E A Control bar D Wire shelf supports B Programmer E Hole for rotisserie C Lamp •Accessories Your appliance is equipped with a flat safety grid with a handle, a 20mm dish and a turnspit.
99643561_A_ML.qxp EN 30/08/2007 13:53 Page 82 3 / DESCRIPTION OF YOUR APPLIANCE • ACCESSORIES • Safety grid with handle (fig.1) Equipped with a front handle for a better grip. The grid can be used to hold all dishes and moulds containing foodstuffs to be cooked or browned. It can be used for barbecues (to be placed directly on the grid). fig.1 • Multi-purpose dish (fig.2) It serves as a cake dish and has a sloped edge.
99643561_A_ML.qxp 30/08/2007 13:53 Page 83 EN 3 / DESCRIPTION OF YOUR APPLIANCE • INTRODUCTION TO THE PROGRAMMER L A M B C K J I H D G F E A Cooking modes display H End of cooking display B Oven temperature display. I Cooking end time indicator C Shelf support indicator and selected cooking mode indicator.
99643561_A_ML.qxp EN 30/08/2007 13:53 Page 84 4 / USING YOUR APPLIANCE •How to set the time - When supplied with electricity The display flashes at 12:00 (fig.1) fig.1 Set the time by pressing the + or - touch controls (holding your finger on the touch control allows you to scroll through the numbers rapidly) (fig.2). Example: 12:30 fig.2 Press the START touch control to validate. The time display no longer flashes (fig.3). fig.
99643561_A_ML.qxp 30/08/2007 13:53 Page 85 EN 4 / USING YOUR APPLIANCE •Instant cooking — The programmer should display only the time. It should not be flashing. Press the START (fig.1) touch control then select the cooking time chosen using the + or - buttons (fig.2). fig.1 Example: —> shelf support 2 recommended. — Confirm by pressing the START touch control. The cooking indicator stops flashing. The shelf support indicator and heating elements in use also light up. fig.
99643561_A_ML.qxp EN 30/08/2007 13:53 Page 86 4 / USING YOUR APPLIANCE • PROGRAMMED COOKING - Cooking with immediate start and programmed duration - Select the desired cooking mode and adjust the temperature (see paragraph: instant cooking). - Press the button until the cooking time indicator starts flashing . The display flashes 0:00 to indicate that you can now adjust the setting (fig.1). fig.1 - Press the + or - touch controls to set the desired time. Example: 30 mins cooking time (fig.2).
99643561_A_ML.qxp 30/08/2007 13:53 Page 87 EN 4 / USING YOUR APPLIANCE • PROGRAMMED COOKING - Cooking with delayed start and chosen cooking end time Proceed as with programmed cooking. - Press the button. The display flashes to indicate that you can now adjust the setting (fig1). - Press the + or - touch control to set the desired cooking end time. Example: end of cooking at 16:00 (fig.2). fig.1 — Confirm by pressing the START touch control. fig.
99643561_A_ML.qxp EN 30/08/2007 13:54 Page 88 4 / USING YOUR APPLIANCE • USING THE TIMER FUNCTION - Your oven’s programmer can be used as an independent timer that allows you to count down a time without operating the oven. In this case, the timer display has priority over the clock display. - Press the The button (fig.1). fig.1 timer symbol and 0m00s flash. - Adjust the chosen time by pressing the touch controls + or - (fig.2). - Press the START button to validate. fig.
99643561_A_ML.qxp 30/08/2007 13:54 Page 89 EN 4 / USING YOUR APPLIANCE • CUSTOMISING THE RECOMMENDED TEMPERATURE Select the cooking function: - Press the START button. If you wish to customize the recommended temperature: - Press the °C touch control until the temperature display begins flashing. - Turn the + or - button until the desired temperature appears. - Press the °C or START button to validate.
99643561_A_ML.qxp EN * 30/08/2007 13:54 Page 90 5 / OVEN COOKING MODES CIRCULATING HEAT (recommended temperature 180°C min 35°C max 235°C) •Cooking is controlled by the heating element located at the back of the oven and by the fan. •Rapid temperature increase: Some dishes can be placed in the oven while it is still cold. •This is recommended to retain the moisture in white meat, fish and vegetables. For cooking multiple items on up to 2 levels.
99643561_A_ML.qxp 30/08/2007 13:54 Page 91 EN 5 / OVEN COOKING MODES KEEPING WARM (recommended temperature 80°C min 35°C max 100°C) •This position allows you to keep your food warm by spurts of heat from the element at the back of the oven combined with fan. •Recommended for letting dough rise for bread, brioche, kouglof...without exceeding 40°C (plate warming, defrosting). BREAD (recommended temperature 205°C min 35°C max 275°C) •Recommended cooking sequence for bread making.
99643561_A_ML.qxp EN 30/08/2007 13:54 Page 92 6 / CARING FOR AND CLEANING YOUR APPLIANCE • PYROLYTIC OVEN - Your oven cleans itself via high-temperature elimination of soil caused by spills and splattering. - The smoke released is destroyed as it moves through a catalyser. You should not wait until the oven is overly coated in grease to initiate a cleaning cycle.
99643561_A_ML.qxp 30/08/2007 13:54 Page 93 6 / CARING FOR AND CLEANING YOUR APPLIANCE EN • PROGRAM A PYROLYSIS •Instant pyrolysis Warning Remove the grids and trays from the oven and clean any major spill residue. - Check that the programmer is displaying the time of day and that it is not flashing. You can choose between 3 pyrolysis cycle times: pyrolysis lasting 1 hour 30 minutes. pyrolysis lasting 1 hour 45 minutes. pyrolysis lasting 2 hours Press the START button (fig.1).
99643561_A_ML.qxp EN 30/08/2007 13:54 Page 94 6 / CARING FOR AND CLEANING YOUR APPLIANCE • PROGRAM A PYROLYSIS •Delayed pyrolysis - Follow the instructions described in the “Programming for immediate pyrolysis” section. After validating the pyrolysis cycle with the START button: fig.1 - Press the button. The end of cooking time flashes to indicate that it is now possible to set it (fig.1). - Press the + or - touch control to set the desired end time (fig.2). Example: End of cooking at 18:00.
99643561_A_ML.qxp 30/08/2007 13:54 Page 95 EN 7 / TROUBLESHOOTING If you have a doubt about the correct functioning of your oven, this does not necessarily mean that there is a malfunction. In any event, check the following items: YOU OBSERVE THAT… POSSIBLE CAUSES WHAT SHOULD YOU DO? The oven is not heating. - The oven is not connected to the ➡ Plug in your oven. power supply. ➡ Replace the fuse in your - Your fuse is out of order. electrical set-up and check its capacity (16A).
99643561_A_ML.qxp EN 30/08/2007 13:54 Page 96 7 / TROUBLESHOOTING Warning - Disconnect your oven before performing any task on the bulb to avoid the risk of electric shock and, if necessary, let the appliance cool down. Tip To unscrew the port and the bulb, use a rubber glove, which will make disassembly easier. • CHANGING THE BULB The bulb is located on the ceiling of your oven’s cavity. a) Unplug the oven. Bulb b) Unscrew the lighting port (fig.1). c) Unscrew the bulb in the same direction.
99643561_A_ML.qxp 30/08/2007 13:54 Page 97 EN 8 / AFTER-SALES SERVICE • REPAIRS Any repairs that are made to your appliance must be handled by a qualified professional authorised to work on the brand. When you call, mention your appliance’s complete reference (model, type, serial number). This information appears on the manufacturer’s nameplate (fig.1). BRANDT APPLIANCES SAS 7 rue Henri Becquerel 92500 RUEIL MALMAISON MADE IN FRANCE 230V ~ 50 Hz fig.
