Specifications

ManualsBrandsDCS ManualsKitchen AppliancesWDU models

UC864-E/G/WD/E-DUAL

AT Commands Reference Guide

SW Release 08.01.XX7 for UC864-E/G/WD/E-DUAL

80304ST10041a Rev. 7 - 2010-10-14

Summary of content (318 pages)

PAGE 1
UC864-E/G/WD/E-DUAL AT Commands Reference Guide SW Release 08.01.XX7 for UC864-E/G/WD/E-DUAL 80304ST10041a Rev.
PAGE 2
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 APPLICABILITY TABLE PRODUCT UC864-E UC864-G UC864-WD UC864-E-DUAL Reproduction forbidden without Telit Communications S.p.A’s. written authorization - All Rights Reserved.
PAGE 3
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 Disclaimer The information contained in this document is the proprietary information of Telit Communications S.p.A. and its affiliates (“TELIT”). The contents are confidential and any disclosure to persons other than the officers, employees, agents or subcontractors of the owner or licensee of this document, without the prior written consent of Telit, is strictly prohibited.
PAGE 4
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 Contents 1. Introduction .............................................................................................................5 1.1. Scope............................................................................................................................ 5 1.2. Audience ...................................................................................................................... 5 1.3.
PAGE 5
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 1. Introduction 1.1. Scope To describe all AT commands implemented on the Telit wireless modules specified in the aforementioned applicability table. 1.2. Audience Readers of this document should be familiar with Telit modules and their ease of controlling by means of AT Commands. 1.3.
PAGE 6
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 1.4. Text Conventions Danger – This information MUST be followed or catastrophic equipment failure or bodily injury may occur. Caution or Warning – Alerts the user to important points about integrating the module, if these points are not followed, the module and end user equipment may fail or malfunction. Tip or Information – Provides advice and suggestions that may be useful when integrating the module.
PAGE 7
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 Issue #7 2010-10-14 08.01.xx7 Change of specification of UC864-WD/E-DUAL Updated description of AT #BND and #SKTOP Reproduction forbidden without Telit Communications S.p.A’s. written authorization - All Rights Reserved.
PAGE 8
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 2. ITEM UC864 family Product Specification UC864-E Air interface ▪ Single-Band UMTS/HSDPA 2100MHz ▪ Quad-Band GSM 850/900/1800/1900 Size 36.2(L)X30(W)X4.8(T) Data Service FEATURE UC864-G UC864-E-DUAL ▪ Tri-band UMTS/HSDPA 2100/1900/850 ▪ Quad-Band GSM 850/900/1800/1900 ▪ Standalone GPS HSDPA UL 384kbps, DL 7.2Mbps WCDMA UL/DL 384kbps, EDGE UL/,DL 236.8Kbps, GPRS UL/DL 85.6 Kbps, CSD 9.
PAGE 9
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3. AT COMMANDS The Telit wireless module family can be driven via the serial interface using the standard 1 AT commands . The Telit wireless module family is compliant with: 1. Hayes standard AT command set, in order to maintain the compatibility with existing SW programs. 2. 3gpp TS 27.
PAGE 10
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.1. Definitions The following syntactical definitions apply: Carriage return character, is the command line and result code terminator character, which value, in decimal ASCII between 0 and 255,is specified within parameter S3. The default value is 13. Linefeed character, is the character recognised as line feed character. Its value, in decimal ASCII between 0 and 255, is specified within parameter S4.
PAGE 11
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.2. AT Command Syntax The syntax rules followed by Telit implementation of either Hayes AT commands and GSM/WCDMA commands are very similar to those of standard basic and extended AT commands. There are two types of extended command: - Parameter type commands.
PAGE 12
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.2.1. String Type Parameters A string, either enclosed between quotes or not, is considered to be a valid string type parameter input. According to V25.
PAGE 13
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 ATCMD1 CMD2=10+CMD1;+CMD2=, ,10;+CMD1?;+CMD1=? anyway it is always preferable to separate into different command lines the basic commands and the extended commands; furthermore it is suggested to avoid placing several action commands in the same command line, because if one of them fails, then an error message is received but it is not possible to argue which one of them has failed the execution.
PAGE 14
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.2.2.1. ME Error Result Code - +CME ERROR: This is NOT a command, it is the error response to +Cxxx 3gpp TS 27.007 commands. Syntax: +CME ERROR: Parameter: - error code can be either numeric or verbose (see +CMEE).
PAGE 15
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 16
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.2.2.2. Message Service Failure Result Code - +CMS ERROR: This is NOT a command; it is the error response to +Cxxx 3gpp TS 27.005 commands Syntax: +CMS ERROR: Parameter: - numeric error code. The values are reported in the table: Numeric Format 0...127 128...255 300 301 302 303 304 305 310 311 312 313 314 315 316 317 318 320 321 322 330 331 332 340 500 Meaning 3gpp TS 24.
PAGE 17
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.2.3.
PAGE 18
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.2.4. Command Response Time-Out Every command issued to the Telit modules returns a result response if response codes are enabled (default). The time needed to process the given command and return the response varies, depending on the command type. Commands that do not interact with the SIM or the network, and involve only internal set up settings or readings, have an immediate response, depending on SIM configuration(e.g.
PAGE 19
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 20
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 21
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.2.5. #CSURVBC 125 #CSURVP 125 #CSURVPC 125 Command Issuing Timing The chain Command -> Response shall always be respected and a new command must not be issued before the module has terminated all the sending of its response result code (whatever it may be).
PAGE 22
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.3. Storage 3.3.1. Factory Profile And User Profiles The Telit wireless modules stores the values set by several commands in the internal non volatile memory (NVM), allowing to remember this setting even after power off.
PAGE 23
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 24
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #VAUX stored by #VAUXSAV command. #USERID, #PASSW, #PKTSZ, #DSTO, #SKTTO, #SKTSET #SKTCT stored by #SKTSAV command and automatically restored at startup; factory default valutes are restored by #SKTRST command. #ESMTP, #EADDR, #EUSER, #EPASSW stored by #ESAV command and automatically restored at startup; factory default valutes are restored by #ERST command.
PAGE 25
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.4. AT Commands Availability Table The following table lists the AT commands set and matches the availability of every single command versus the Telit wireless module family.
PAGE 26
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 27
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 COMMAND UC864-EFunction DUAL Call Waiting   Call Holding Services   Unstructured Supplementary Service Data   Advice Of Charge   List Current Calls   SS Notification   Closed User Group Supplementary Service Control   Preferred Operator List   Selection of Preferred PLMN List   ETSI GSM 07.07/27.
PAGE 28
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 COMMAND UC864-EFunction DUAL ETSI GSM 07.05/27.005 – Message Configuration Service Center Address   Select Service for MO SMS messages   Set Text Mode Parameters   Show Text Mode Parameters   Select Cell Broadcast Message Types   Save Settings   Restore Settings   ETSI GSM 07.05/27.
PAGE 29
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 30
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 31
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 32
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5. AT Commands References 3.5.1. Command Line General Format 3.5.1.1. Command Line Prefixes 3.5.1.1.1. Starting A Command Line - AT AT - Starting A Command Line AT The prefix AT, or at, is a two-character abbreviation (ATtention), always used to start a command line to be sent from TE to TA Reference 3GPP TS 27.007 3.5.1.1.2.
PAGE 33
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.2. General Configuration Commands 3.5.2.1.1. Select Interface Style - #SELINT #SELINT - Select interface style AT#SELINT= Set command sets the AT command interface style depending on parameter . Parameter: - AT command interface 2 - switches the AT command interface style of the product, to UC864 family AT#SELINT? AT#SELINT=? Note 3.5.2.1.2. Read command reports the current interface style.
PAGE 34
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #NOPT - Set notification port USB Diagnostic and UART TRACE are reserved for Telit Service. USB Modem,USB Auxiliary and UART DATA are dedicated for M2M Interface. Parameter: - Notification Port 0 – All Ports (Telit USB Modem,UART Data, USB Auxiliary) Notification data is sent to all ports.
PAGE 35
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.3. Hayes Compliant AT Commands 3.5.3.1. Generic Modem Control 3.5.3.1.1. Set To Factory-Defined Configuration - &F &F - Set To Factory-Defined Configuration AT&F[] Execution command sets the configuration parameters to default values specified by manufacturer; it takes in consideration hardware configuration switches and other manufacturer-defined criteria.
PAGE 36
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +FCLASS - Select Active Service Class Parameter: 0 - data 1 - fax class 1 8 - voice AT+FCLASS? Read command returns the current configuration value of the parameter . AT+FCLASS=? Test command returns all supported values of the parameters . Note “ATD;” (end with semicolon) will initiate voice call no matter which connection mode is set by +FCLASS. Reference 3GPP TS 27.007 3.5.3.1.4.
PAGE 37
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 &P - Default Reset Full Profile Designation Reference 3.5.3.1.6. Note: if parameter is omitted, the command has the same behaviour as AT&P0 Telit Specifications Store Current Configuration - &W &W - Store Current Configuration AT&W[] Execution command stores on profile the complete configuration of the device. Parameter: 0..1 - profile Note: if parameter is omitted, the command has the same behaviour of AT&W0.
PAGE 38
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 &N - Display Internal Phonebook Stored Numbers Parameter: - phonebook record number Note: if parameter is omitted then all the internal records are shown. 3.5.3.1.9. Manufacturer Identification - +GMI +GMI - Manufacturer Identification AT+GMI Execution command returns the manufacturer identification. Reference 3.5.3.1.10. V.
PAGE 39
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +GSN - Serial Number Note: The number returned from the same command in Telit GC series is board serial number. UC864 series returns IMEI assigned to the indivisual product. Reference V.25ter 3.5.3.1.14. Display Current Base Configuration And Profile - &V &V - Display Current Base Configuration And Profile AT&V Execution command returns some of the base configuration parameters settings. 3.5.3.1.15.
PAGE 40
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.3.1.17. Extended S Registers Display - &V3 &V3 - Extended S Registers Display AT&V3 Execution command returns the value of the S registers in decimal and hexadecimal value in the format: REG DEC HEX ... where - S register number 000..005 007 012 025 030 038 - current value in decimal notation - current value in hexadecimal notation 3.5.3.1.18.
PAGE 41
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +GCI - Country Of Installation 59 - it currently supports only the Italy country code AT+GCI? Read command reports the currently selected country code. AT+GCI=? Test command reports the supported country codes. Reference V25ter. 3.5.3.1.21. Line Signal Level - %L %L - Line Signal Level AT%L It has no effect and is included only for backward compatibility with landline modems 3.5.3.1.22.
PAGE 42
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 E - Command Echo Reference 3.5.3.2.2. Note: if parameter is omitted, the command has the same behaviour of ATE0 V25ter Quiet Result Codes - Q Q - Quiet Result Codes ATQ[] Set command enables or disables the result codes.
PAGE 43
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 V - Response Format result codes 1 - full headers and trailers and verbose format of result codes (factory default) information responses result codes Note: the portion of information responses is not affected by this setting.
PAGE 44
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.3.2.4. Extended Result Codes - X X - Extended Result Codes ATX[] Set command selects the result code messages subset used by the modem to inform the DTE of the result of the commands. Parameter: 0 - send only OK, CONNECT, RING, NO CARRIER, ERROR, NO ANSWER results. Busy tones reporting is disabled. 1..4 - reports all messages (factory default is 1).
PAGE 45
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.3.2.6. Data Carrier Detect (DCD) Control - &C &C - Data Carrier Detect (DCD) Control AT&C[] Set command controls the RS232 DCD output behaviour. Parameter: 0 - DCD remains high always. 1 - DCD follows the Carrier detect status: if carrier is detected DCD is high, otherwise DCD is low. (factory default) 2 - DCD off while disconnecting Reference 3.5.3.2.7.
PAGE 46
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.3.2.8. Standard Flow Control - \Q \Q - Standard Flow Control AT\Q[] Set command controls the RS232 flow control behaviour.
PAGE 47
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.3.2.10. Data Set Ready (DSR) Control - &S &S - Data Set Ready (DSR) Control AT&S[] Set command controls the RS232 DSR pin behaviour. Parameter: 0 - always High 1 - follows the GSM traffic channel indication. 2 - High when connected 3 - High when device is ready to receive commands (factory default).
PAGE 48
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +IPR - Fixed DTE Interface Rate AT+IPR= Set command specifies the DTE speed (UART only) at which the device accepts commands during command mode operations; it may be used to fix the DTE-DCE interface speed. Parameter: 300 600 1200 2400 4800 9600 19200 38400 57600 115200 (default) 230400 AT+IPR? AT+IPR=? Read command returns the current value of +IPR parameter.
PAGE 49
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +IFC - DTE-Modem Local Flow Control Note: Hardware flow control (AT+IFC=2,2) is not active in command mode. AT+IFC? Note: This command is equivalent to &K command. Read command returns active flow control settings. Note: If flow control behavior has been set with AT&Kn command with the parameter that is not allowed by AT+IFC the read command AT+IFC? will return: AT+IFC=? Reference 3.5.3.2.14.
PAGE 50
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +ICF - DTE-Modem Character Framing 0 - Odd (not supported) 1 - Even (not supported) AT+ICF? Read command returns current settings for subparameters and . The current setting of subparameter will always represented as 0. Test command returns the ranges of values for the parameters and V25ter AT+ICF = 3 - 8N1 (default) AT+ICF=? Reference Example AT+ICF=? +ICF: (3) 3.5.3.3.
PAGE 51
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 D – Dial Note: parameter is case sensitive. ATD>[;] Note: used character set should be the one selected with +CSCS. Issues a call to phone number in phonebook memory storage , entry location (available memories may be queried with AT+CPBS=?). If “;” is present a voice call is performed.
PAGE 52
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 D – Dial ATDG[;] ATDg[;] ATD* [*][*[] [*[]]]]# I - invocation, restrict CLI presentation i - suppression, allow CLI presentation Issues a call checking the CUG supplementary service information for the current call. Refer to +CCUG command. If “;” is present a voice call is performed.
PAGE 53
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 P - Pulse Dial ATP Set command has no effect is included only for backward compatibility with landline modems. V25ter. Reference 3.5.3.3.4. Answer - A A - Answer ATA Execution command is used to answer to an incoming call if automatic answer is disabled. Note: This command MUST be the last in the command line and must be followed immediately by a character. V25ter. Reference 3.5.3.3.5.
PAGE 54
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.3.3.7. Guard Tone - &G &G - Guard Tone AT&G 3.5.3.3.8. Set command has no effect is included only for backward compatibility with landline modems. Sync/Async Mode - &Q &Q - Sync/Async Mode AT&Q Set command has no effect is included only for backward compatibility with landline modems. Reproduction forbidden without Telit Communications S.p.A’s. written authorization - All Rights Reserved.
PAGE 55
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.3.4. Modulation Control 3.5.3.4.1. Modulation Selection - +MS +MS - Modulation Selection AT+MS= Set command has no effect is included only for backward compatibility with landline modems.
PAGE 56
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.3.5. Compression Control 3.5.3.5.1. Data Compression - +DS +DS - Data Compression AT+DS=[
[,[,[,]]]] Parameter: . : desired direction of operations 0 - no compression (factory default) 1 - Transmit only. 2 - Receive only. 3 - Both directions, accept any direction.
PAGE 57
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +DR - Data Compression Reporting AT+DR=? Test command returns all supported values of the parameter Reference V25ter 3.5.3.6. Break Control 3.5.3.6.1. Transmit Break To Remote - \B \B - Transmit Break To Remote AT\B Execution command has no effect and is included only for backward compatibility with landline modems 3.5.3.6.2.
PAGE 58
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.3.7. S Parameters Basic commands that begin with the letter “S” are known as “S-Parameters”. The number following the “S” indicates the “parameter number” being referenced. If the number is not recognized as a valid parameter number, an ERROR result code is issued. If no value is given for the subparameter of an S-Parameter, an ERROR result code will be issued and the stored value left unchanged.
PAGE 59
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.3.7.2. Ring Counter - S1 S1 - Ring Counter ATS1 ATS1? 3.5.3.7.3. S1 is incremented each time the device detects the ring signal of an incoming call. S1 is cleared as soon as no ring occur. Note: the form ATS1 has no effect. Read command returns the value of this parameter. Escape Character - S2 S2 - Escape Character ATS2=[] Set command sets the ASCII character to be used as escape character.
PAGE 60
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 S3 - Command Line Termination Character 0s Reference V25ter Reproduction forbidden without Telit Communications S.p.A’s. written authorization - All Rights Reserved.
PAGE 61
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.3.7.5. Response Formatting Character - S4 S4 - Response Formatting Character ATS4=[] Set command sets the value of the character generated by the device as part of the header, trailer, and terminator for result codes and information text, along with the S3 parameter. Parameter: - response formatting character (decimal ASCII) 0..
PAGE 62
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 S7 - Connection Completion Time-Out - number of seconds 1..255 - factory default value is 60 ATS7? Read command returns the current value of S7 parameter. Reference 3.5.3.7.8.
PAGE 63
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.3.7.10. Delay To DTR Off - S25 S25 -Delay To DTR Off ATS25=[] Set command defines the amount of time, in hundredths of second, that the device will ignore the DTR for taking the action specified by command &D. Parameter: - expressed in hundredths of a second 0..255 - factory default value is 5. ATS25? Note: the delay is effective only if its value is greater than 5.
PAGE 64
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 S38 -Delay Before Forced Hang Up Note: parameter can be used to ensure that data in device buffer is sent before device disconnects. ATS38? Read command returns the current value of S38 parameter. Note: the format of the numbers in output is always 3 digits, left-filled with 0s Reproduction forbidden without Telit Communications S.p.A’s. written authorization - All Rights Reserved.
PAGE 65
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4. 3GPP TS 27.007 AT Commands 3.5.4.1. General 3.5.4.1.1. Request Manufacturer Identification - +CGMI +CGMI - Request Manufacturer Identification AT+CGMI Execution command returns the device manufacturer identification code without command echo. AT+CGMI=? Test command returns OK result code. Reference 3GPP TS 27.007 3.5.4.1.2.
PAGE 66
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CSCS - Select TE Character Set “GSM” - GSM default alphabet (3GPP TS 03.38/23.008) “IRA” - international reference alphabet (ITU-T T.50) ”8859-1” - ISO 8859 Latin 1 character set ”PCCP437” - PC character set Code Page 437 ”UCS2” - 16-bit universal multiple-octet coded character set (ISO/IEC10646) AT+CSCS? AT+CSCS=? Reference 3.5.4.1.6. Read command returns the current value of the active character set.
PAGE 67
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.1.8. Multiplexing Mode - +CMUX +CMUX - Multiplexing Mode Set command is used to enable/disable the GSM 07.10 multiplexing AT+CMUX= protocol control channel. Parameters: [,] multiplexer transparency mechanism 0 - basic option; it is currently the only supported value. 0 - UIH frames used only; it is currently the only supported value.
PAGE 68
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.2. Call Control 3.5.4.2.1. Hang Up Call - +CHUP +CHUP - Hang Up Call AT+CHUP AT+CHUP=? Reference 3.5.4.2.2. Execution command cancels all active and held calls, also if a multi-party session is running. Test command returns the OK result code GSM 07.
PAGE 69
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CBST - Select Bearer Service Type 39 - 9600 bps (V.120) 43 - 14400 bps (V.120) 48 - 28800 bps (V.120) 51 - 56000 bps (V.120) 71 - 9600 bps (V.110 or X.31 flag stuffing) 75 - 14400 bps (V110 or X.31 flag stuffing) 80 - 14400 bps (V110 or X.31 flag stuffing) 81 - 38400 bps (V110 or X.31 flag stuffing) 83 - 56000 bps (V110 or X.31 flag stuffing) 84 - 64000 bps ( X.
PAGE 70
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CBST - Select Bearer Service Type AT+CBST=80,0,1 (V.110 28.8k, non transparent) AT+CBST=81,0,1 (V.110 38.4k, non transparent) AT+CBST=83,0,1 (X.31FS 56k, non transparent) AT+CBST=83,4,1 (X.31FS 56k RDI, non transparent) AT+CBST=84,0,1 (X.31FS 64k, non transparent) AT+CBST=116,1,0 (Bit transparent 64 kbps, transparent) AT+CBST? AT+CBST=? Reference 3.5.4.2.4.
PAGE 71
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.2.5. Service Reporting Control - +CR +CR - Service Reporting Control AT+CR=[] Set command controls whether or not intermediate result code +CR is returned from TA to TE.
PAGE 72
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CEER - Extended Error Report - the failure in the last unsuccessful call setup (originating or answering) - the last call release - the last unsuccessful GPRS attach or unsuccessful PDP context activation, - the last GPRS detach or PDP context deactivation. AT+CEER=? Reference 3.5.4.2.7.
PAGE 73
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.2.8. Single Numbering Scheme - +CSNS +CSNS - Single Numbering Scheme AT+CSNS= Set command selects the bearer to be used when mobile terminated single [] numbering scheme call is established. Parameter values set with +CBST command shall be used when equals to a data service. Parameter: 0 - voice (factory default) 2 - fax (TS 62) 4 - data AT+CSNS? AT+CSNS=? Reference 3.5.4.2.9.
PAGE 74
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.3. Network Service Handling 3.5.4.3.1. Subscriber Number - +CNUM +CNUM - Subscriber Number AT+CNUM Execution command returns the MSISDN (if the phone number of the device has been stored in the SIM card) in the format: +CNUM: ,,[ +CNUM: ,,[…]] AT+CNUM=? Example Reference 3.5.4.3.2.
PAGE 75
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.3.3. Network Registration Report - +CREG +CREG - Network Registration Report AT+CREG= Set command enables/disables network registration reports depending on [] the parameter .
PAGE 76
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CREG - Network Registration Report AT Example OK at+creg? +CREG: 0,2 OK (the MODULE is in network searching state) at+creg? +CREG: 0,2 OK at+creg? +CREG: 0,2 OK at+creg? +CREG: 0,2 OK at+creg? +CREG: 0,1 OK (the MODULE is registered) at+creg? +CREG: 0,1 Reference 3.5.4.3.4. OK 3GPP TS 27.
PAGE 77
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +COPS - Operator Selection 4 - manual/automatic ( field shall be present); if manual selection fails, automatic mode (=0) is entered 0 - alphanumeric long form (max length 16 digits) 1 - short format alphanumeric 2 - numeric 5 digits [country code (3) + network code (2)] : network operator in format defined by parameter.
PAGE 78
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +COPS - Operator Selection require some seconds before the output is given. AT+COPS? Example +COPS: 0,0,"Test PLMN 1-1",0 OK at+cops=? +COPS: (2,"","","45008",2),(1,"Test PLMN 1-1","Test11","00101",0),(3,"","","45005",2),,(0-4),(0-2) OK Reference 3.5.4.3.5. 3GPP TS 27.007 Facility Lock/Unlock - +CLCK +CLCK - Facility Lock/Unlock AT+CLCK= Execution command is used to lock or unlock a ME or a network facility.
PAGE 79
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 80
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CPWD - Change Facility Password - string type, it shall be the same as password specified for the facility from the ME user interface or with command +CPWD. - string type, it is the new password AT+CPWD=? Example Reference 3.5.4.3.7. Note: parameter is the old password while is the new one.
PAGE 81
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CLIP - Calling Line Identification Presentation set should be the one selected with command Select TE character set +CSCS. 0 - CLI valid 1 - CLI has been withheld by the originator. 2 - CLI is not available due to interworking problems or limitation or originating network.
PAGE 82
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 83
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +COLP - Connected line identification presentation 0 – disable 1 – enable 0 - COLP not provisioned 1 - COLP provisioned 2 - unknown (e.g. no network, etc.) AT+COLP=? Test command returns supported parameters Reference 3GPP TS 27.007 3.5.4.3.10. Call Forwarding Number And Conditions - +CCFC +CCFC - Call Forwarding Number And Condition AT+CCFC= Execution command controls the call forwarding supplementary service.
PAGE 84
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CCFC - Call Forwarding Number And Condition 8 - short message service 16 - data circuit sync 32 - data circuit async 64 - dedicated packet access 128 - dedicated PAD access - time in seconds to wait before call is forwarded; it is valid only when "no reply" is enabled (=1) or queried (=2) 1..
PAGE 85
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 86
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CCWA - Call Waiting Note: the difference between call waiting report disabling (AT+CCWA = 0,1,7) and call waiting service disabling (AT+CCWA = 0,0,7) is that in the first case the call waiting indication is sent to the device by network but this last one does not report it to the DTE; instead in the second case the call waiting indication is not generated by the network.
PAGE 87
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CHLD - Call Holding Services AT+CHLD=? Test command returns the list of supported s. Reference Note 3.5.4.3.13. +CHLD: (0,1,1X,2,2X,3,4) 3GPP TS 27.007 ONLY for VOICE calls Unstructured Supplementary Service Data - +CUSD +CUSD - Unstructured Supplementary Service Data AT+CUSD= Set command allows control of the Unstructured Supplementary Service [[, Data (USSD [3GPP TS 02.90/22.090]).
PAGE 88
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CUSD - Unstructured Supplementary Service Data 3 - other local client has responded 4 - operation not supported 5 - network time out AT+CUSD? AT+CUSD=? Reference Note 3.5.4.3.14. Read command reports the current value of the parameter Test command reports the supported values for the parameter 3GPP TS 27.
PAGE 89
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.3.15.
PAGE 90
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.3.16. SS Notification - +CSSN +CSSN - SS Notification AT+CSSN=[ It refers to supplementary service related network initiated notifications. [,]] Set command enables/disables the presentation of notification result codes from TA to TE.
PAGE 91
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.3.17. Closed User Group Supplementary Service Control - +CCUG +CCUG - Closed User Group Supplementary Service Control AT+CCUG= Set command allows control of the Closed User Group supplementary [[, service [3GPP TS 02.85/22.085]. [,]]] Parameters: 0 - disable CUG temporary mode (factory default).
PAGE 92
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CPOL - Preferred Operator List 1 – access technology selected - UTRA acess technology 0 – access technology not selected 1 – access technology selected AT+CPOL? AT+CPOL=? Reference 3.5.4.3.19. Note: if is given but is left out, entry is deleted. If is given but is left out, is put in the next free location.
PAGE 93
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.4. Mobile Equipment Control 3.5.4.4.1.
PAGE 94
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CFUN - Set Phone Functionality functionality level =1.
PAGE 95
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CPIN - Enter PIN the PIN the command +CPWD must be used instead. Parameters: - string type value - string type value. To check the status of the PIN request use the command AT+CPIN? AT+CPIN? Note: If all parameters are omitted then the behaviour of Set command is the same as Read command.
PAGE 96
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 97
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CPIN - Enter PIN Reference 3.5.4.4.4. 3GPP TS 27.007 Signal Quality - +CSQ +CSQ - Signal Quality AT+CSQ Execution command reports received signal quality indicators in the form: +CSQ: , where - received signal strength indication 0 - (-113) dBm or less 1 - (-111) dBm 2..30 - (-109)dBm..
PAGE 98
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CIND - Indicator Control [,[,…]]] associated indicator changes.
PAGE 99
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 100
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CMER - Mobile Equipment Event Reporting 0 - discard +CIEV Unsolicited Result Codes. 1 - discard +CIEV Unsolicited Result Codes when TA-TE link is reserved (e.g. on-line data mode); otherwise forward them directly to the TE. 2 - buffer +CIEV Unsolicited Result Codes in the TA when TA-TE link is reserved (e.g. on-line data mode) and flush them to the TE after reservation; otherwise forward them directly to the TE.
PAGE 101
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CPBS - Select Phonebook Memory Storage applicable for this storage) "RC" - ME received calls list (+CPBF is not applicable for this storage). “DC” - MT dialled calls list “ME” – MT phonebook “EN” - SIM/USIM (or MT) emergency number (+CPBW is not be applicable for this storage) “ON” - SIM (or MT) own numbers (MSI torage may be available through +CNUM also).
PAGE 102
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CPBR - Read Phonebook Entries where: - the location number of the phonebook entry - string type phone number of format - type of phone number octet in integer format 129 - national numbering scheme 145 - international numbering scheme (contains the character "+") - the alphanumeric text associated to the number; used character set should be the one selected with command +CSCS.
PAGE 103
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CPBR - Read Phonebook Entries OK Reference 3GPP TS 27.007 3.5.4.4.9. Find Phonebook Entries - +CPBF +CPBF - Find Phonebook Entries AT+CPBF= Execution command returns phonebook entries (from the current phonebook memory storage selected with +CPBS) which alphanumeric field start with string . Parameter: - string type; used character set should be the one selected with command +CSCS.
PAGE 104
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CPBF - Find Phonebook Entries Note Remember to select the PB storage with +CPBS command before issuing PB commands.
PAGE 105
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CPBW - Write Phonebook Entry AT+CPBW=? Note: if either “LD”, “MC” or “RC” memory storage has been selected (see +CPBS) it is possible just to delete the phonebook entry in location , therefore parameters , and must be omitted.
PAGE 106
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CCLK - Clock Management mm - minute (two last digits are mandatory), range is (00..59) ss - seconds (two last digits are mandatory), range is (00..59) ±zz - time zone (indicates the difference, expressed in quarter of an hour, between the local time and GMT; two last digits are mandatory), range is -47..+48 AT+CCLK? Read command returns the current setting of the real-time clock, in the format .
PAGE 107
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CALA - Alarm Management does nothing. (Default) 2 - the MODULE wakes up in "alarm mode" if at the alarm time it was off, otherwise it remains fully operative. In both cases the MODULE issues an unsolicited code every 3s: +CALA: where is the +CALA optional parameter previously set. The device keeps on sending the unsolicited code every 3s until a #WAKE or #SHDN command is received or a 90 seconds timer expires.
PAGE 108
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CALA - Alarm Management “0” - it sets a recurrent alarm for all days in the week. - integer type indicating if the alarm is silent or not. 0 - the alarm will not be silent; 1 - the alarm will be silent.
PAGE 109
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CRSM - Restricted SIM Access 214 - UPDATE BINARY 220 - UPDATE RECORD 242 - STATUS - identifier of an elementary data file on SIM. Mandatory for every command except STATUS. ,, - parameter passed on by the ME to the SIM; they are mandatory for every command except GET RESPONSE and STATUS 0..255 - information to be read/written to the SIM (hexadecimal character format).
PAGE 110
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 111
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CALM - Alert Sound Mode Reference 3GPP TS 27.007 3.5.4.4.15. Ringer Sound Level - +CRSL +CRSL - Ringer Sound Level AT+CRSL= Set command is used to select the incoming call ringer sound level of the device.
PAGE 112
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.4.17. Microphone Mute Control - +CMUT +CMUT - Microphone Mute Control AT+CMUT= Set command enables/disables the muting of the microphone audio line during a voice call. Parameter: 0 - mute off, microphone active (factory default) 1 - mute on, microphone muted. AT+CMUT? AT+CMUT=? Reference 3.5.4.4.18. Note: this command mutes/activates both microphone audio paths, internal mic and external mic.
PAGE 113
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.4.19. Accumulated Call Meter Maximum - +CAMM +CAMM - Accumulated Call Meter Maximum AT+CAMM= Set command sets the Advice of Charge related Accumulated Call Meter [ Maximum Value stored in SIM (ACMmax). This value represents the [,]] maximum number of home units allowed to be consumed by the subscriber. When ACM reaches value further calls are prohibited.
PAGE 114
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CPUC - Price Per Unit And Currency Table AT+CPUC=? Reference 3.5.4.4.21. +CACM : , Test command returns the OK result code 3GPP TS 27.007 Available AT Commands - +CLAC +CLAC - Available AT Commands AT+CLAC Execution command causes the ME to return the AT commands that are available for the user, in the following format: [[…]] AT+CLAC=? Reference 3.5.4.4.22.
PAGE 115
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.5. Mobile Equipment Errors 3.5.4.5.1. Report Mobile Equipment Error - +CMEE +CMEE - Report Mobile Equipment Error AT+CMEE=[] Set command enables/disables the report of result code: +CME ERROR: as an indication of an error relating to the +Cxxx commands issued. When enabled, device related errors cause the +CME ERROR: final result code instead of the default ERROR final result code.
PAGE 116
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.6. Voice Control 3.5.4.6.1. DTMF Tones Transmission - +VTS +VTS - DTMF Tones Transmission AT+VTS= Execution command allows the transmission of DTMF tones. [,duration] Parameters: - string of s, i.e.
PAGE 117
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.7. Commands For GPRS 3.5.4.7.1. GPRS Mobile Station Class - +CGCLASS +CGCLASS - GPRS mobile station class AT+CGCLASS= Set command sets the GPRS class according to parameter.
PAGE 118
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CGATT - GPRS Attach Or Detach Reference 3GPP TS 27.007 3.5.4.7.3. GPRS Event Reporting - +CGEREP +CGEREP - GPRS Event Reporting AT+CGEREP= Set command enables or disables sending of unsolicited result codes [[,]] +CGEV: XXX (see below) from TA to TE in the case of certain events occurring in the TA or the network.
PAGE 119
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CGEREP - GPRS Event Reporting +CGEV: ME DEACT , , [] The mobile equipment has forced a context deactivation. The that was used to activate the context is provided if known to TA +CGEV: NW DETACH The network has forced a GPRS detach. This implies that all active contexts have been deactivated. These are not reported separately +CGEV: ME DETACH The mobile equipment has forced a GPRS detach.
PAGE 120
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.7.4. GPRS Network Registration Status - +CGREG +CGREG - GPRS Network Registration Status AT+CGREG=[] Set command controls the presentation of an unsolicited result code +CGREG: (see format below).
PAGE 121
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.7.5.
PAGE 122
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CGDCONT - Define PDP Context OK AT+CGDCONT? +CGDCONT: 1,”IP”,“APN”,”10.10.10.10”,0,0 OK AT+CGDCONT=? +CGDCONT: (1-16),"IP",,,(0-2),(0-4) +CGDCONT: (1-16),"PPP",,,(0-2),(0-4) +CGDCONT: (1-16),"IPV6",,,(0-2),(0-4) OK 3GPP TS 27.007 Reference 3.5.4.7.6.
PAGE 123
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CGQMIN - Quality Of Service Profile (Minimum Acceptable) context and the supported values for the subparameters in the format: +CGQMIN: ,(list of supported s), (list of supported s),(list of supported s), (list of supported s),(list of supported s) Example Note: only the “IP” PDP_Type is currently supported.
PAGE 124
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 125
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CGEQMIN – 3G Quality Of Service Profile (Minimum Acceptable) 1 – yes 2 – no detect 3 – subscribed value Transfer delay (milliseconds) 0 – subscribed value 100…4000 Traffic handling priority 0- subscribed value 1…3 AT+CGEQMIN? Note: a special form of the Set command, +CGEQMIN= causes the requested profile for context number to become undefined.
PAGE 126
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 127
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CGQREQ - Quality Of Service Profile (Requested) returned.
PAGE 128
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 129
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 130
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 131
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CGACT - PDP Context Activate Or Deactivate Example AT+CGACT=1,1 OK AT+CGACT? +CGACT: 1,1 OK 3GPP TS 27.007 Reference 3.5.4.7.11.
PAGE 132
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.7.12. 3G Quality of Service Profile (Negotiated) - +CGEQNEG +CGEQNEG – 3G Quality Of Service Profile (Negotiated) AT+CGEQNEG= This command allow the TE to retrieve the negotiated 3G quality of service [[,[,…]]] profiles returned in the Activate PDP Context Accept message. Set command returns the negotiated 3G QoS profile for the specified context identifiers, s.
PAGE 133
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CGDATA - Enter Data State "PPP" - PPP Point-to-point protocol - numeric parameter which specifies a particular PDP context definition (see +CGDCONT command). AT+CGDATA=? Example Reference Note: if parameter is omitted, the layer 2 protocol is unspecified Test command reports information on the supported layer 2 protocols. AT+CGDATA=? +CGDATA: (”PPP”) OK AT+CGDATA=”PPP”,1 OK 3GPP TS 27.
PAGE 134
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.4.8. Commands For Battery Charger 3.5.4.8.1.
PAGE 135
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 + CBC - Battery Charge Reference 3GPP TS 27.007 Reproduction forbidden without Telit Communications S.p.A’s. written authorization - All Rights Reserved.
PAGE 136
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.5. 3GPP TS 27.005 AT Commands for SMS and CBS 3.5.5.1. General Configuration 3.5.5.1.1. Select Message Service - +CSMS +CSMS - Select Message Service AT+CSMS= Set command selects messaging service . It returns the types of messages supported by the ME: Parameter: 0 - The syntax of SMS AT commands is compatible with 3GPP TS 27.005 Phase 2 version 4.7.
PAGE 137
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CSMS - Select Message Service AT+CSMS? +CSMS: 1,1,1,1 Reference 3.5.5.1.2. OK 3GPP TS 27.005; 3GPP TS 03.40/23.040; 3GPP TS 03.41/23.041 Preferred Message Storage - +CPMS +CPMS - Preferred Message Storage AT+CPMS= Set command selects memory storages , and to [, be used for reading, writing, sending and storing SMs.
PAGE 138
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CPMS - Preferred Message Storage AT+CPMS=? Example where , and are the selected storage memories for reading, writing and storing respectively.
PAGE 139
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.5.2. Message Configuration 3.5.5.2.1. Service Center Address - +CSCA +CSCA -Service Center Address AT+CSCA= Set command sets the Service Center Address to be used for mobile originated SMS transmissions.
PAGE 140
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CGSMS – Select service for MO SMS messages -a numeric parameter which indicates the service or service pref erence to be used. 0 – Packet Domain 1 - Circuit switched (factory default) 2 – Packet Domain preferred (use circuit switched if GRPS is not available) 3 - Circuit switched preferred (use Packet Domain if circuit switched not ava ilable) AT+CGSMS? AT+CGSMS=? Reference 3.5.5.2.3.
PAGE 141
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CSMP - Set Text Mode Parameters AT+CSMP=? Test command returns the OK result code. Example Set the parameters for an outgoing message with 24 hours of validity period and default properties: Reference 3.5.5.2.4. AT+CSMP=17,167,0,0 OK 3GPP TS 27.005; 3GPP TS 03.40/23.040; 3GPP TS 03.38/23.
PAGE 142
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.5.2.5. Select Cell Broadcast Message Types - +CSCB +CSCB -Select Cell Broadcast Message Types AT+CSCB= Set command selects which types of Cell Broadcast Messages are to be [[, received by the device.
PAGE 143
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CSAS - Save Settings AT+CSAS=? Reference 3.5.5.2.7. Note: If parameter is omitted the settings are saved in the non volatile memory. Test command returns the possible range of values for the parameter . 3GPP TS 27.005 Restore Settings - +CRES +CRES - Restore Settings AT+CRES Execution command restores message service settings saved by +CSAS [=] command from either NVM or SIM.
PAGE 144
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.5.3. Message Receiving And Reading 3.5.5.3.1. New Message Indications To Terminal Equipment - +CNMI +CNMI - New Message Indications To Terminal Equipment AT+CNMI=[ Set command selects the behaviour of the device on how the receiving of [, new messages from the network is indicated to the DTE.
PAGE 145
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 146
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CNMI - New Message Indications To Terminal Equipment (PDU Mode) +CBM: where: - PDU length - message PDU (TEXT Mode) +CBM:,,,, where: - message serial number - message ID - Data Coding Scheme - page number - total number of pages of the message - CBM Content of Message  If indicates that GSM03.38/23.
PAGE 147
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 148
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.5.3.2. List Messages - +CMGL +CMGL - List Messages AT+CMGL Execution command reports the list of all the messages with status value [=] stored into message storage ( is the message storage for read and delete SMs as last settings of command +CPMS).
PAGE 149
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CMGL - List Messages ] where - message position in the storage - message status - originator/destination address, string type , represented in the currently selected character set (see +CSCS) - string type alphanumeric representation of or , corresponding to an entry found in the phonebook; used character set is the one selected with command +CSCS.
PAGE 150
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CMGL - List Messages SMS Test message +CMGL: 2,"REC UNREAD","+821020955219",,"07/07/26,20:05:58+36" SMS Test message... +CMGL: 3,"REC UNREAD","+821020955219",,"07/07/26,20:06:37+36" SMS Test Message.. +CMGL: 4,"REC UNREAD","+821020955219",,"07/07/26,20:07:43+36" TEST MESSAGE..
PAGE 151
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CMGR - Read Message - status of the message 0 - new message 1 - read message 2 - stored message not yet sent 3 - stored message already sent - string type alphanumeric representation of or , corresponding to an entry found in the phonebook; used character set is the one selected with command +CSCS. - length of the PDU in bytes. - message in PDU format according to 3GPP TS 3.40/23.040.
PAGE 152
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CMGR - Read Message - string type alphanumeric representation of or , corresponding to an entry found in the phonebook; used character set is the one selected with command +CSCS.
PAGE 153
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CNMA – New Message Acknowledgement Z/ESC]]] 1(+CSMS=1) when a +CMT or +CDS indication is show. If no acknowledgement is given within the network timeout, an RP-ERROR is sent to the network, the and parameters of the +CNMI command are then reset to zero (do not show new message indication). Either positive (RP-ACK) or negative (RP-ERROR) acknowledgement to the network is possible.
PAGE 154
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CNMA – New Message Acknowledgement AT+CNMA=0 OK Message is received from network. +CMT: "",70 06816000585426000480980600F170110370537284… Send negative acknowledgement(Unspecified error) to the network. AT+CNMA=2,3 > 00FF00 OK (Text Mode) SMS AT commands compatible with 3GPP TS 27.005 Phase 2+ version . AT+CSMS=1 +CSMS: 1,1,1 OK Set Text mode. AT+CMGF=1 OK AT+CNMI=2,2,0,0,0 OK Message is received from network.
PAGE 155
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.5.4. Message Sending And Writing 3.5.5.4.1. Send Message - +CMGS +CMGS - Send Message (PDU Mode) AT+CMGS= (PDU Mode) Execution command sends to the network a message. Parameter: - length of the PDU to be sent in bytes (excluding the SMSC address octets). 7..
PAGE 156
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CMGS - Send Message - TP-Service Centre Time Stamp in Time String Format. Note: if message sending fails for some reason, an error code is reported. (Text Mode) AT+CMGS= [,] Note: care must be taken to ensure that during the command execution, which may take several seconds, no other SIM interacting commands are issued. (Text Mode) Execution command sends to the network a message.
PAGE 157
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CMGS - Send Message To send the message issue Ctrl-Z char (0x1A hex). To exit without sending the message issue ESC char (0x1B hex). If message is successfully sent to the network, then the result is sent in the format: Note : Optionally (when +CSMS value is 1 and network supports) is returned: +CMGS: [, ] where - message reference number.
PAGE 158
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CMGS - Send Message OK Reference 3GPP TS 27.005 Reproduction forbidden without Telit Communications S.p.A’s. written authorization - All Rights Reserved.
PAGE 159
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.5.4.2. Send Message From Storage - +CMSS +CMSS - Send Message From Storage AT+CMSS= Execution command sends to the network a message which is already [, stored in the storage (see +CPMS) at the location .
PAGE 160
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CMSS - Send Message From Storage OK 3GPP TS 27.005 Reference 3.5.5.4.3. Write Message To Memory - +CMGW +CMGW - Write Message To Memory (PDU Mode) AT+CMGW= [,] (PDU Mode) Execution command writes in the memory storage a new message. Parameter: - length in bytes of the PDU to be written. 7..164 - message status.
PAGE 161
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CMGW - Write Message To Memory selected character set (see +CSCS). - type of destination address. 129 - number in national format 145 - number in international format (contains the "+") - message status.
PAGE 162
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CMGW - Write Message To Memory +CMGW: where: - message location index in the memory . If message storing fails for some reason, an error code is reported. Note: care must be taken to ensure that during the command execution, no other SIM interacting commands are issued.
PAGE 163
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CMGD - Delete Message - message index in the selected storage - an integer indicating multiple message deletion request.
PAGE 164
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +CMMS – More Message to Send is automatically reset to 0: the feature is disabled. 2 - Keep link opened while messages are sent. If the delay between two messages exceeds 3 seconds, the link is closed but the parameter is remains set to 2: the feature is still enabled. AT+CMMS? AT+CMMS=? Reference Read command reports the current value of the parameter . Test command reports the supported value of parameter.
PAGE 165
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.6. FAX Class 1 AT Commands 3.5.6.1. General Configuration 3.5.6.1.1. Manufacturer ID - +FMI +FMI - Manufacturer ID AT+FMI? Read command reports the manufacturer ID. Example AT+FMI? Telit OK Reference ITU T.31 and TIA/EIA-578-A specifications 3.5.6.1.2. Model Id - +FMM +FMM - Model ID AT+FMM? Reference 3.5.6.1.3. Read command reports the model ID ITU T.
PAGE 166
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.6.2. Transmission/Reception Control 3.5.6.2.1. Stop Transmission And Pause - +FTS +FTS - Stop Transmission And Pause AT+FTS= Execution command causes the modem to terminate a transmission and wait for 10ms intervals before responding with OK result. AT+FTS=? Parameter: - duration of the pause, expressed in 10ms intervals. 0..255 Test command returns all supported values of the parameter .
PAGE 167
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +FTM - Transmit Data AT+FTM=? 73 - V17/7200 bps Training Long 74 - V17/7200 bps Training Short 96 - V29/9600 bps 97 - V17/9600 bps Training Long 98 - V17/9600 bps Training Short Test command returns all supported values of the parameter . Reference Note: test command result is without command echo ITU T.31 and TIA/EIA-578-A specifications 3.5.6.2.4.
PAGE 168
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +FTH - Transmit Data With HDLC Framing Reference ITU T.31 and TIA/EIA-578-A specifications 3.5.6.2.6. Receive Data With HDLC Framing - +FRH +FRH - Receive Data Data With HDLC Framing AT+FRH= Execution command causes the module to receive facsimile data using HDLC protocol and the modulation defined by the parameter .
PAGE 169
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.6.3. Serial Port Control 3.5.6.3.1. Select Flow Control Specified By Type - +FLO +FLO - Select Flow Control Specified By Type AT+FLO= Set command selects the flow control behaviour of the serial port in both directions: from DTE to DTA and from DTA to DTE.
PAGE 170
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +FPR - Select Serial Port Rate Note: test command result is without command echo Reference ITU T.31 and TIA/EIA-578-A specifications 3.5.6.3.3. Double Escape Character Replacement Control - +FDD +FDD - Double Escape Character Replacement Control AT+FDD= Set command concerns the use of the _{pair to encode consecutive escape characters (<10h><10h>) in user data.}
PAGE 171
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 +FIT - DTE inactivity timeout Note: The inactivity timer starts when the DCE has taken some action that requires DTE response. If the DTE does respond, the DCE shall reset the inactivity timer. AT+FIT? Read command reports the current value of the parameters AT+FIT=? Test command returns all supported values of the parameters. Reference ITU T.31 and TIA/EIA-578-A specifications 3.5.6.3.5.
PAGE 172
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7. Custom AT Commands 3.5.7.1. General Configuration AT Commands 3.5.7.1.1. Manufacturer Identification - #CGMI #CGMI - Manufacturer Identification AT#CGMI Execution command returns the device manufacturer identification code with command echo. AT#CGMI=? Test command returns the OK result code. Example AT#CGMI #CGMI: Telit OK 3.5.7.1.2.
PAGE 173
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #CGSN - Product Serial Number Identification Example AT#CGSN #CGSN: 358677008900540 OK 3.5.7.1.5. International Mobile Subscriber Identity (IMSI) - #CIMI #CIMI - International Mobile Subscriber Identity (IMSI) AT#CIMI Execution command returns the international mobile subscriber identity, identified as the IMSI number, with command echo. AT#CIMI=? Test command returns the OK result code.
PAGE 174
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.1.8.
PAGE 175
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.1.10. Select Ringer Sound - #SRS #SRS - Select Ringer Sound AT#SRS= Set command sets the ringer sound. [,] Parameters: - ringing tone 0 - current ringing tone 1..max - ringing tone number, where max can be read by issuing the Test command AT#SRS=?. - ringing tone playing time-out in seconds. 0 - ringer is stopped (if present) and current ringer sound is set. 1..
PAGE 176
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.1.11. Select Ringer Path - #SRP #SRP - Select Ringer Path AT#SRP=[] Set command selects the ringer path towards whom sending ringer sounds and all signalling tones.
PAGE 177
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #STM - Signaling Tones Mode #STM: Test command reports supported range of values for parameter . AT#STM=? 3.5.7.1.13. Tone Playback - #TONE #TONE - Tone Playback AT#TONE= Execution command allows the reproduction of DTMF tones, standard free [,] tone, standard busy tone, and a set of user defined tones for a certain time.
PAGE 178
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 179
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 180
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.1.16. Display PIN Counter - #PCT #PCT - Display PIN Counter AT#PCT Execution command reports the PIN/PUK or PIN2/PUK2 input remaining attempts, depending on +CPIN requested password in the format: #PCT: AT#PCT=? Example where: - remaining attempts 0 - the SIM is blocked. 1..3 - if the device is waiting either SIM PIN or SIM PIN2 to be given. 1..
PAGE 181
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.1.18. Wake From Alarm Mode - #WAKE #WAKE - Wake From Alarm Mode AT#WAKE= Execution command stops any eventually present alarm activity and, if the [] module is in alarm mode, it exits the alarm mode and enters the normal operating mode. Parameter: - operating mode 0 - normal operating mode; the module exits the alarm mode, enters the normal operating mode, any alarm activity is stopped (e.g.
PAGE 182
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #QTEMP - Query Temperature Overflow #QTEMP: where: - over temperature indicator 0 - the device temperature is in the working range 1 - the device temperature is out of the working range Note: typical temperature working range is (-10°C..
PAGE 183
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 Setting of the following optional parameters has meaning only if =0: - URC presentation mode.
PAGE 184
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 required only if =4 is enabled. Note: if the is specified shall assume values from 4-7. Note: last settings are saved as extended profile parameters.
PAGE 185
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #GPIO - General Purpose Input/Output Pin Control Parameters: - GPIO pin number; supported range is from 1 to a value that depends on the hardware.
PAGE 186
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #GPIO - General Purpose Input/Output Pin Control AT#GPIO? Note: while using the pins in the alternate function, the GPIO read/write access to that pin is not accessible and shall be avoided. Read command reports the read direction and value of all GPIO pins, in the format: #GPIO:
,[#GPIO: ,[…]] AT#GPIO=? Example 3.5.7.1.22.
PAGE 187
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SLED - STAT_LED GPIO Setting Note: values are saved in NVM by command #SLEDSAV AT#SLED? AT#SLED=? 3.5.7.1.23. Note: at module boot the STAT_LED GPIO is always tied High and holds this value until the first NVM reading.
PAGE 188
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #DVI - Digital Voiceband Interface DVI activated for audio. DVI is configured as master providing on DVI Port #2 3.5.7.1.25.
PAGE 189
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #PCMTXG – DVI Microphone Gain AT#PCMTXG= Set command sets the DVI (PCM) Audio TX gain Parameter: : PCM TX volume in TX path (default value=0) TX VOL RANGE : -5000(-50 dB) ~ 1200(+12 dB) Note: meaning of a TX_VOL is 1/100 dB step.
PAGE 190
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #E2SMSRI - SMS Ring Indicator - RI enabling 0 - disables RI pin response for incoming SMS messages (factory default) 50..1150 - enables RI pin response for incoming SMS messages. The value of is the duration in ms of the pulse generated on receipt of an incoming SM. AT#E2SMSRI? Note: if +CNMI=3,1 command is issued and the module is in a GPRS connection, a 100 ms break signal is sent and a 1 sec.
PAGE 191
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #ADC - Read Analog/Digital Converter Input AT#ADC? Read command reports all pins voltage, converted by ADC, in the format: AT#ADC=? 3.5.7.1.30. #ADC: [#ADC: […]] Test command reports the supported range of values of the command parameters , and
. Digital/Analog Converter Control - #DAC #DAC - Digital/Analog Converter Control AT#DAC= Set command enables/disables the DAC_OUT pin.
PAGE 192
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #VAUX- Auxiliary Voltage Output Control AT#VAUX= Set command enables/disables the Auxiliary Voltage pins output.
PAGE 193
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #V24CFG - V24 Output Pins Configuration 1 - CTS (Clear To Send) 2 - RI (Ring Indicator) 3 - DSR (Data Set Ready) 4 - DTR (Data Terminal Ready). This is not an output pin: we maintain this value only for backward compatibility, but trying to set its state raises the result code “ERROR” 5 - RTS (Request To Send).
PAGE 194
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #V24 - V24 Output Pins Control - State of AT commands serial port interface output hardware pins (0, 1, 2, 3) when pin is in GPIO mode (see #V24CFG): 0 - Low 1 - High AT#V24? Note: if is omitted the command returns state of the pin. Read command returns actual state for all the pins in the format: #V24: ,[ #V24: ,[...]] AT#V24=? 3.5.7.1.35.
PAGE 195
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #CBC- Battery And Charger Status 0 - charger not connected 1 - charger connected and charging 2 - charger connected and charge completed - battery voltage in millivolt: it is the real battery voltage only if charger is not connected; if the charger is connected this value depends on the charger voltage. AT#CBC=? Test command returns the OK result code. 3.5.7.1.37.
PAGE 196
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #MSCLASS - Multislot Class Control format: AT#MSCLASS=? 3.5.7.1.39. #MSCLASS: Test command reports the range of available values for both parameters and . Cell Monitor - #MONI #MONI - Cell Monitor AT#MONI[= Set command sets one cell out of seven, in a neighbour of the serving cell []] including it, from which extract GSM/WCDMA-related informations. Parameter: 0..
PAGE 197
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 198
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #MONI - Cell Monitor the format: #MONI: (,) Note 3.5.7.1.40. where: - maximum number of cells, in a neighbour of the serving cell and excluding it, from which we can extract GSM-related informations. This value is always 6. - the last setting done with command #MONI. The refresh time of the measures is preset to 3 sec.
PAGE 199
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #PSNT – Packet Service Network Type #PSNT: , where - network type 0 - GPRS network 1 - EGPRS network 2 - WCDMA network 3 - HSDPA network 4 - unknown or not registered AT#PSNT=? 3.5.7.1.42. Note: Even though registered to WCDMA network which supports HSDPA, it may report 2 if SIB5 is not broadcasted. In this case, it can be checked if the cell is capable of HSDPA when a PS session is active.
PAGE 200
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #RFSTS – Read current network MM RRC NOM BLER CID IMSI NetNameAsc SD nAST nUARFCN nPSC nEc/Io Status in 3G network 19 0 1 005 2825220 "450050203619261" "SKTelecom" 3 3 Mobility Management Radio Resource Control Network Operator Mode Block Error Rate(005 means 0.
PAGE 201
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 202
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #QSS - Query SIM Status #QSS: where: - current SIM status 0 - SIM NOT INSERTED 1 - SIM INSERTED 2 - enabled; the ME informs at every SIM status change through the following unsolicited indication: #QSS: where: - current SIM status 0 - SIM NOT INSERTED 1 - SIM INSERTED 2 - SIM INSERTED and PIN UNLOCKED 3 - SIM INSERTED and READY (SMS and Phonebook access are possible).
PAGE 203
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #DIALMODE - Dialling Mode 2 - (voice call and data call) the following custom result codes are received, monitoring step by step the call status: DIALING (MO in progress) RINGING (remote ring) CONNECTED (remote call accepted) RELEASED (after ATH) DISCONNECTED (remote hang-up) AT#DIALMODE? Note: The setting is saved in NVM and available on following reboot.
PAGE 204
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #ACAL - Automatic Call Note See &Z to write and &N to read the number on module internal phonebook. 3.5.7.1.47. Extended Automatic Call - #ACALEXT #ACALEXT - Extended Automatic Call AT#ACALEXT= Set command enables/disables the extended automatic call function. , Parameters: 0 - disables the automatic call function (factory default) 1 - enables the automatic call function from internal phonebook.
PAGE 205
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #ECAM - Extended Call Monitoring 0 - disables call monitoring function (factory default) 1 - enables call monitoring function; the ME informs about call events, such as incoming call, connected, hang up etc.
PAGE 206
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 207
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.1.51. Message Waiting Indication - #MWI #MWI - Message Waiting Indication AT#MWI= Set command enables/disables the presentation of the message waiting indicator URC.
PAGE 208
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #MWI - Message Waiting Indication . 1 - either Line 1 (CPHS context) or Voice (3GPP context) 2 - Line 2 (CPHS context) 3 - Fax 4 - E-mail 5 - Other - message counter: number of pending messages related to the message waiting indicator as it is stored on SIM.
PAGE 209
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #CODEC - Audio Codec AT#CODEC? Read command returns current audio codec mode in the format: AT#CODEC=? Example #CODEC: Test command returns the range of available values for parameter AT#CODEC=14 OK sets the codec modes HR (4), EFR (2) and AMR-FR (8) 3.5.7.1.53.
PAGE 210
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #HFMICG - Handsfree Microphone Gain AT#HFMICG=? Test command returns the supported range of values of parameter . 3.5.7.1.55. Handset Microphone Gain - #HSMICG #HSMICG - Handset Microphone Gain AT#HSMICG= Set command sets the handset microphone input gain [] Parameter: : handset microphone input gain 0..
PAGE 211
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SPKMUT - Speaker Mute Control Set command enables/disables the global muting of the speaker audio line, AT#SPKMUT= for every audio output ( ring, incoming sms, voice, Network coverage) Parameter: 0 - mute off, speaker active (factory default) 1 - mute on, speaker muted. Note: this command mutes/activates both speaker audio paths, internal speaker and external speaker.
PAGE 212
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 0..6 - handset analogue output (-3dB/step, factory default=0) Note: This parameter is saved in NVM issuing AT&W command. AT#HSRECG? Read command returns the current handset analog output gain, in the format: AT#HSRECG =? 3.5.7.1.60. #HSRECG: Test command returns the supported range of values of parameter .
PAGE 213
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 214
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 215
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.1.65. Handsfree RX AGC Value tuning - #SHFAGCRX #SHFAGCRX – Handsfree RX AGC Value tuning Set command sets the handsfree RX AGC value tuning AT#SHFAGCRX= , , Parameter: ,< agc_exp_slope>, precompressor static gain. This is the gain applied to the input samples when static gain is enabled. Meaningful Range is 0x2000 to 0xFFFF.
PAGE 216
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SHFAGCRX – Handsfree RX AGC Value tuning compression slope. This is the slope of the compressor gain when compression is applied. Meaningful range is 0x8000 to 0xFFFF. Value(agc_compr_sloop) = 65536 * X : X range is 0.50001 to 0.99999 Note: these values are automatically saved in NVM. AT#SHFAGCRX? AT#SHFAGCRX =? 3.5.7.1.66.
PAGE 217
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SHFAGCTX – Handsfree TX AGC Value tuning Value(agc_exp_thres) = 128 ‫( כ‬X+75) : X range is -75 to 0 dBm0mu expansion slope. This is the slope of the expander gain when expansion is applied. Meaningful range is 0xFF01 to 0xFFF6. Value(agc_exp_slope) = 256 * X : X range is -0.04 to -0.996. compression threshold. This is the energy threshold of the input above which compression is applied.
PAGE 218
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 # SHFNR - Handsfree Noise Reduction 0 - disables noise reduction for handsfree mode (default) 1 - enables noise reduction for handsfree mode Note: This parameter is saved in NVM issuing AT&W command. AT#SHFNR? Read command reports whether the noise reduction function on audio handsfree input is currently enabled or not, in the format: AT#SHFNR =? 3.5.7.1.68.
PAGE 219
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SHSEC - Handset Echo Canceller Note: This parameter is saved in NVM issuing AT&W command. AT#SHSEC? Read command reports whether the echo canceller function on audio handset output is currently enabled or not, in the format: #SHSEC: Test command returns the supported range of values of parameter . AT#SHSEC =? 3.5.7.1.70.
PAGE 220
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SHSSD - Set Handset Sidetone #SHSSD: AT#SHSSD=? Test command returns the supported range of values of parameter . 3.5.7.1.72. Handset RX AGC Value tuning - #SHSAGCRX #SHSAGCRX – Handset RX AGC Value tuning Set command sets the handset RX AGC value tuning AT#SHSAGCRX= , , Parameter: ,< agc_exp_slope>, precompressor static gain.
PAGE 221
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SHSAGCRX – Handset RX AGC Value tuning compression threshold. This is the energy threshold of the input above which compression is applied. Meaningful range is 0x0 to 0x2580. This parameter must be greater than agc_exp_thres. Value(agc_compr_thres) = 128 ‫( כ‬X+75) : X range is -75 to 0 dBm0mu compression slope. This is the slope of the compressor gain when compression is applied.
PAGE 222
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SHSAGCTX – Handset TX AGC Value tuning Meaningful value is just 0x0000 or 0xFFFF. expansion threshold. This is the energy threshold of the input under which expansion is applied. This parameter must be less than agc_compr_thres. Meaningful range is 0x0 to 0x2580. Write 0 to disable the expander. Value(agc_exp_thres) = 128 ‫( כ‬X+75) : X range is -75 to 0 dBm0mu expansion slope.
PAGE 223
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SRXAGC – RX AGC Enable AT#SRXAGC= Set command sets the RX AGC enabling Parameter: 0 - disables rx agc (default) 1 - enables rx agc Note: RX AGC enabling makes RX level decreasing Note: these values are automatically saved in NVM. AT#SRXAGC? AT#SRXAGC=? 3.5.7.1.75. Read command returns the current RX AGC values: #SRXAGC: Test command returns the supported range of values of parameter .
PAGE 224
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SHSFTX - Handset TX filter coefficients values ,,,, ,, Parameter: : Filter Tap, h[0] and h[12] : Filter Tap, h[1] and h[11] : Filter Tap, h[2] and h[10] : Filter Tap, h[3] and h[9] : Filter Tap, h[4] and h[8] : Filter Tap, h[5] and h[7] : Filter Tap, h[6] Note: these values are automatically saved in NVM. AT#SHSFTX? AT#SHSFTX=? 3.5.7.1.77.
PAGE 225
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 226
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #NITZ - Network Timezone 4 - it sets the #NITZ URC ‘extended’ format (see below) 8 – it sets the #NITZ URC ‘extended’ format with Daylight Saving Time (DST) support (see below). Note: Default value for UC864-G AT&T (08.01.127) is 7.
PAGE 227
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.1.81. Select Band - #BND #BND - Select Band AT#BND= Set command selects the current band.
PAGE 228
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #BND - Select Band Note: the range of values differs between triband modules and quadricband modules 3.5.7.1.82. Automatic Band Selection - #AUTOBND #AUTOBND - Automatic Band Selection AT#AUTOBND= Set command enables/disables the automatic band selection at power-on.
PAGE 229
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SKIPESC - Skip Escape Sequence 0 - doesn’t skip the escape sequence; its transmission is enabled (factory default). 1 - skips the escape sequence; its transmission is not enabled. AT#SKIPESC? AT#SKIPESC=? 3.5.7.1.84. Note: in case of an FTP connection, the escape sequence is not transmitted, regardless of the command setting.
PAGE 230
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #GAUTH - PPP-GPRS Connection Authentication Type AT#GAUTH= Set command sets the PPP-GPRS connection authentication type. [] Parameter 3 – AUTO authentication (PAP and CHAP , factory default) AT#GAUTH? Note: for PPP passive mode , is fixed to AUTO.
PAGE 231
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 [, [,]]]] 0 - detection algorithm not active 1 - detection algorithm active; detection is started every period, using for detection. 2 - triggers the new measurement of the antenna presence, reporting the result in the format: #GSMAD: where: 0 - antenna connected. 1 - antenna connector short circuited to ground. 2 - antenna connector short circuited to power.
PAGE 232
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 Note: #GSMAD parameters, excluding , are saved in NVM. Test command reports the supported range of values for parameters , , , and . Read command returns the current parameter settings for #GSMAD command in the format: AT#GSMAD=? AT#GSMAD? #GSMAD: ,,,, 3.5.7.1.88.
PAGE 233
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.1.89. SIM Enhanced Speed #ENHSIM - SIM Enhanced Speed AT#ENHSIM= Set command activates or deactivates the Sim Enhanced Speed Functionality. Parameter: 0 - Not Active (default) 1 - BRF is (F=512 D=8) 2 - BRF is (F=512 D=16) 3 - BRF is (F=512 D=32) (For BRF definition refer to ISO-7816-3 AT#ENHSIM? AT#ENHSIM=? Reference 3.5.7.1.90.
PAGE 234
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 235
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #CCLK - Clock Management Example AT#CCLK="02/09/07,22:30:00+04,1" OK AT#CCLK? #CCLK: 02/09/07,22:30:25+04,1 OK 3.5.7.1.92. TeleType Writer - #TTY #TTY - TeleType Writer AT#TTY= Set command enables/disables the TTY functionality.
PAGE 236
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.1.93. Power Saving Mode Ring Indicator - #PSMRI #PSMRI – Power Saving Mode Ring Indicator AT#PSMRI= Set command enables/disables the Ring Indicator pin response to an URC message while modem is in power saving mode. If enabled, a negative going pulse is generated, when URC message for specific event is invoked. The duration of this pulse is determined by the value of .
PAGE 237
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.1.95.
PAGE 238
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #PLMNMODE – Apply to New Operator Names AT#PLMNMODE=? Test command returns supported values of the parameter . 3.5.7.1.97. Network Scan Timer - #NWSCANTMR #NWSCANTMR - Network Scan Timer AT#NWSCANTMR= Set command sets the Network Scan Timer that is used by the module to schedule the next network search when it is without network coverage (no signal).
PAGE 239
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #NWEN - Network Emergency Number Update #NWEN: where: 1 – number list update from internal ME 2 – number list update from SIM 3 – number list update from network AT#NWEN? AT#NWEN=? 3.5.7.1.99. Note: is saved in NVM.
PAGE 240
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.1.100. GCF Flag Set #GCFS – GCF Flag Set AT#GCFS= Set command sets the GCF parameters values.
PAGE 241
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.1.102. Enhanced Network Selection - #ENS #ENS - Enhanced Network Selection (UC864-G AT&T only) AT#ENS=[] Set command is used to activate the ENS functionality.
PAGE 242
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #EONS ? Enable URC of Enhanced Operator Name String : Alpha tag of network name Note: Name string can be any network name as well as EONS and sent by its priority. The following order of priority for which name source is to be used: 1. EF-SPN. 2. EF-OPL and EF-PNN. 3. CPHS Operator Name String. 4. Name Information received by the NITZ service. 5. Any name stored internal to the ME. 6. Displaying the broadcast MCC-MNC.
PAGE 243
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.2. Multisocket AT Commands 3.5.7.2.1. Socket Status - #SS #SS - Socket Status AT#SS Execution command reports the current status of the sockets in the format: #SS: ,,,,, [,,,,, […]] where: - socket connection identifier 1..6 - actual state of the socket: 0 - Socket Closed.
PAGE 244
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 245
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SI - Socket Info We have information only about socket number 1 3.5.7.2.3. Context Activation - #SGACT #SGACT - Context Activation AT#SGACT=, Execution command is used to activate or deactivate the specified PDP [,, context. ] Parameters: - PDP context identifier 1..
PAGE 246
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SH - Socket Shutdown Parameter: - socket connection identifier 1..6 AT#SH=? 3.5.7.2.5. Note: a socket connection can be closed only when it is in suspended mode (with pending data too). Trying to close an active socket connection will produce an error. Test command reports the range for parameter .
PAGE 247
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SCFG - Socket Configuration AT#SCFG=? Test command returns the range of supported values for all the subparameters. at#scfg? #SCFG: 1,1,300,90,600,50 #SCFG: 2,2,300,90,600,50 #SCFG: 3,2,250,90,600,50 #SCFG: 4,1,300,90,600,50 #SCFG: 5,1,300,90,600,50 #SCFG: 6,1,300,90,600,50 Example OK 3.5.7.2.6.
PAGE 248
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SCFGEXT - Socket Configuration Extended - TCP keepalive timer timeout 0 - TCP keepalive timer is deactivated (default) 1..240 - TCP keepalive timer timeout in minutes - currently not used 0 - reserved for future use - currently not used 0 - reserved for future use Note: has effect only on TCP connections.
PAGE 249
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SD - Socket Dial 1 - UDP - remote host port to contact 0..65535 - address of the remote host, string type. This parameter can be either: - any valid IP address in the format: “xxx.xxx.xxx.
PAGE 250
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SD - Socket Dial AT#SD=? Example Test command reports the range of values for all the parameters. Open socket 1 in online mode AT#SD=1,0,80,”www.google.com”,0,0,0 CONNECT … Open socket 1 in command mode AT#SD=1,0,80,”www.google.com”,0,0,1 OK 3.5.7.2.8.
PAGE 251
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.2.10. Socket Listen - #SL #SL - Socket Listen AT#SL=, This command opens/closes a socket listening for an incoming connection , on a specified port. [,] Parameters: - socket connection identifier 1..6 0 - closes socket listening 1 - starts socket listening - local listening port 0..
PAGE 252
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SL - Socket Listen 1.1.1.1.1 Receive Data In Command Mode - #SRECV #SRECV – Received Data in Command Mode Execution command permits the user to read data arrived through a AT#SRECV= connected socket, but buffered and not yet read because the module , entered command mode before reading them; the module is notified of these data by a SRING URC, whose presentation format depends on the last #SCFGEXT setting.
PAGE 253
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SRECV – Received Data in Command Mode SRING URC ( be 2, be 0) displaying (in text format) 15 bytes data that have just come through connected socket identified by =3; it’s no necessary to issue #SRECV to read the data; no data remain in the buffer after this URC SRING: 3,15, stringa di test 3.5.7.2.11.
PAGE 254
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.2.12. Socket Listen UDP - #SLUDP #SLUDP - Socket Listen UDP AT#SLUDP=, This command opens/closes a socket listening for an incoming UDP , connection on a specified port. Parameters: - socket connection identifier 1..6 0 - closes socket listening 1 - starts socket listening - local listening port 1..
PAGE 255
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.3. FTP AT Commands 3.5.7.3.1. FTP Time-Out - #FTPTO #FTPTO - FTP Time-Out AT#FTPTO= Set command sets the time-out used when opening either the FTP control [] channel or the FTP traffic channel. Parameter: - time-out in 100 ms units 100..5000 - hundreds of ms (factory default is 100) AT#FTPTO? Note: The parameter is not saved in NVM.
PAGE 256
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.3.4. FTP Put - #FTPPUT #FTPPUT - FTP Put AT#FTPPUT= Execution command, issued during an FTP connection, opens a data [] connection and starts sending file to the FTP server. If the data connection succeeds, a CONNECT indication is sent, otherwise a NO CARRIER indication is sent. Parameter: - string type, name of the file. Note: use the escape sequence +++ to close the data connection.
PAGE 257
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #FTPTYPE - FTP Type 0 - binary 1 - ascii #FTPTYPE? Note: The command causes an ERROR result code to be returned if no FTP connection has been opened yet. Read command returns the current file transfer type, in the format: #FTPTYPE=? #FTPTYPE: Test command returns the range of available values for parameter : #FTPTYPE: (0,1) 3.5.7.3.7.
PAGE 258
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.3.10. FTP Change Working Directory - #FTPCWD #FTPCWD - FTP Change Working Directory AT#FTPCWD= Execution command, issued during an FTP connection, changes the working [] directory on FTP server. Parameter: - string type, it’s the name of the new working directory. AT#FTPCWD=? 3.5.7.3.11. Note: The command causes an ERROR result code to be returned if no FTP connection has been opened yet.
PAGE 259
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.4. Enhanced Easy GPRS® Extension AT Commands 3.5.7.4.1. Authentication User ID - #USERID #USERID - Authentication User ID AT#USERID= Set command sets the user identification string to be used during the [] authentication step. Parameter: - string type, it’s the authentication User Id; the max length for this value is the output of Test command, AT#USERID=? (factory default is the empty string “”).
PAGE 260
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.4.3. Packet Size - #PKTSZ #PKTSZ - Packet Size AT#PKTSZ= Set command sets the default packet size to be used by the TCP/UDP/IP [] stack for data sending. AT#PKTSZ? AT#PKTSZ=? Example Parameter: - packet size in bytes 0 - automatically chosen by the device 1..1500 - packet size in bytes (factory default is 300) Read command reports the current packet size value.
PAGE 261
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #DSTO -Data Sending Time-Out whose sending would have been delayed for an undefined time until new data to be sent had been received and full packet size reached. AT#DSTO? Read command reports the current data sending time-out value. AT#DSTO=? Test command returns the allowed values for the parameter . Example AT#DSTO=10 ->1 sec. time-out OK AT#DSTO? #DSTO: 10 OK 3.5.7.4.5.
PAGE 262
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SKTSET - Socket Definition , - socket protocol type [], 0 - TCP (factory default) []] 1 - UDP - remote host port to be opened 0..65535 - port number (factory default is 3333) - address of the remote host, string type. This parameter can be either: - any valid IP address in the format: xxx.xxx.xxx.
PAGE 263
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.4.7. Socket Open - #SKTOP #SKTOP - Socket Open AT#SKTOP Execution command activates the context number 1, proceeds with the authentication with the user ID and password previously set by #USERID and #PASSW commands, and opens a socket connection with the host specified in the #SKTSET command. Eventually, before opening the socket connection, it issues automatically a DNS query to solve the IP address of the host name.
PAGE 264
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.4.9. DNS Response Caching - #CACHEDNS #CACHEDNS - DNS Response Caching AT#CACHEDNS= Set command enables caching a mapping of domain names to IP [] addresses, as does a resolver library. Parameter: 0 - caching disabled; it cleans the cache too 1 - caching enabled Note: the validity period of each cached entry (i.e.
PAGE 265
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #DNS – Manual DNS Selection “xxx.xxx.xxx.xxx” used for the specified cid; we’re using this value instead of the secondary DNS server come from the network (default is “0.0.0.0”). Note: if is ”0.0.0.0.0” and is not “0.0.0.0”, then issuing AT#DNS=… raises an error. Note: if is ”0.0.0.0.0” we’re using the primary DNS server come from the network as consequence of a context activation.
PAGE 266
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SKTCT - Socket TCP Connection Time-Out query (if the peer was specified by name and not by address) is not counted in this time-out. AT#SKTCT? Read command reports the current TCP connection time-out. AT#SKTCT=? Test command returns the allowed values for parameter . Example AT#SKTCT=600 OK socket first connection answer time-out has been set to 60 s. 3.5.7.4.12.
PAGE 267
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SKTRST - Socket Parameters Reset - Data Sending Time-Out - Socket Type - Remote Port - Remote Address - TCP Connection Time-Out AT#SKTRST=? Test command returns the OK result code. Example AT#SKTRST OK socket parameters have been reset 3.5.7.4.14.
PAGE 268
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #GPRS - GPRS Context Activation AT#GPRS=0 OK Now GPRS context has been deactivated, IP is lost. 3.5.7.4.15. Socket Dial - #SKTD #SKTD - Socket Dial AT#SKTD= [, , , [], []] Set command opens the socket towards the peer specified in the parameters.
PAGE 269
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SKTD - Socket Dial - AT#SKTD? AT#SKTD=? Example coverage is enough to permit a connection the GPRS has been activated with AT#GPRS=1 Note: If all parameters are omitted then the behaviour of Set command is the same as Read command.
PAGE 270
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SKTL - Socket Listen Command returns the OK result code if successful.
PAGE 271
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SKTL - Socket Listen OK Start listening AT#SKTL=1,0,1024 OK or AT#SKTL=1,0,1024,255 OK Receive connection requests +CONN FROM: 192.164.2.1 CONNECT exchange data with the remote host send escape sequence +++ NO CARRIER Now listen is not anymore active to stop listening Note 3.5.7.4.17.
PAGE 272
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #E2SLRI - Socket Listen Ring Indicator AT#E2SLRI=? Test command returns the allowed values for parameter . 3.5.7.4.18. Firewall Setup - #FRWL #FRWL - Firewall Setup AT#FRWL= Execution command controls the internal firewall settings.
PAGE 273
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #FRWL - Firewall Setup 197.158.1.1 to 197.158.255.255 We need to add the following chain to the firewall: Note AT#FRWL=1,"197.158.1.1","255.255.0.0" OK For outgoing connections made with #SKTOP and #SKTD the remote host is dynamically inserted into the ACCEPT chain for all the connection duration.
PAGE 274
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #GDATAVOL - GPRS Data Volume - number of bytes transmitted in the last GPRS session for PDP context; - number of bytes received in the last GPRS session for PDP context; 2 - it reports the total GPRS data counter, since last reset, for the all the set PDP contexts (i.e.
PAGE 275
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #ICMP – ICMP Ping Support AT#ICMP? Read command returns whether the ICMP Ping support is currently enabled or not, in the format: #ICMP: AT#ICMP=? Test command reports the supported range of values for the parameter. 3.5.7.4.21. Maximum TCP Payload Size - #TCPMAXDAT #TCPMAXDAT – Maximum TCP Payload Size Set command allows to set the maximum TCP payload size in TCP header AT#TCPMAXDAT= options.
PAGE 276
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.5. E-mail Management AT Commands 3.5.7.5.1. E-mail SMTP Server - #ESMTP #ESMTP - E-mail SMTP Server AT#ESMTP= Set command sets the SMTP server address, used for E-mail sending. [] SMTP server can be specified as IP address or as nick name. Parameter: - SMTP server address, string type. This parameter can be either: - any valid IP address in the format: xxx.xxx.xxx.
PAGE 277
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #EADDR - E-mail Sender Address OK 3.5.7.5.3. E-mail Authentication User Name - #EUSER #EUSER - E-mail Authentication User Name AT#EUSER= Set command sets the user identification string to be used during the [] authentication step of the SMTP. Parameter: - e-mail authentication User ID, string type. - any string value up to max length reported in the Test command.
PAGE 278
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #EPASSW - E-mail Authentication Password empty "". AT#EPASSW=? Test command returns the maximum allowed length of the string parameter . Example AT#EPASSW="myPassword" OK Note It is a different password field than the one used for GPRS authentication (see #PASSW). 3.5.7.5.5.
PAGE 279
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #SEMAIL - E-mail Sending With GPRS Context Activation #EMAILD instead of it. 3.5.7.5.6. E-mail GPRS Context Activation - #EMAILACT #EMAILACT - E-mail GPRS Context Ativation AT#EMAILACT= Execution command deactivates/activates the GPRS context, eventually [] proceeding with the authentication with the parameters given with #PASSW and #USERID.
PAGE 280
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #EMAILD - E-mail Sending To complete the operation send Ctrl-Z char (0x1A hex); to exit without writing the message send ESC char (0x1B hex). If e-mail message is successfully sent, then the response is OK. If message sending fails for some reason, an error code is reported Note: Care must be taken to ensure that during the command execution, no other commands are issued.
PAGE 281
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #ERST - E-mail Parameters Reset AT#ERST Execution command resets the actual e-mail parameters in the NVM of the device to the default ones. AT#ERST=? 3.5.7.5.10. The values reset are: - E-mail User Name - E-mail Password - E-mail Sender Address - E-mail SMTP server Test command returns the OK result code.
PAGE 282
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.6. Easy Scan® Extension AT Commands Note: it is strongly suggested to issue all the Easy Scan® Extension AT commands with NO SIM inserted, to avoid a potential conflict with normal module operations, such as “incoming call”, “periodic location update, “periodic routing area update” and so on. 3.5.7.6.1.
PAGE 283
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #CSURV - Network Survey is only applicable for serving cell - decimal number; it is the receiption level (in dBm) - decimal number; it is the bit error rate (in %). is not available in UC864 family. it is always return 0.00.
PAGE 284
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #CSURV - Network Survey - packet broadcast control channel 0 - pbcch not activated on the cell 1 - pbcch activated on the cell - network operation mode 1 2 3 - routing area code 0..255 - SPLIT_PG_CYCLE support ..0 - SPLIT_PG_CYCLE is not supported on CCCH on this cell ..1 - SPLIT_PG_CYCLE is supported on CCCH on this cell - priority access threshold 03..6 - network control order 0..
PAGE 285
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 286
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #CSURV - Network Survey array: 14 19 22 48 82 arfcn: 14 rxLev: 8 Network survey ended OK (wcdma) at#csurv Network survey started ... uarfcn: 10812 rxLev: -87 mcc: 450 mnc: 08 scr code: 6528 cellId: 10683976 lac: 5121 cellStatus: CELL_LOW_PRIORITY uarfcn: 10713 rxLev: -87 mcc: 450 mnc: 05 scr code: 1200 cellId: 2171648 lac: 8209 cellStatus: CELL_LOW_PRIORITY Network survey ended Note 3.5.7.6.2.
PAGE 287
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #CSURVC - Network Survey (Numeric Format) reported, each of them in the format: In 2G (For BCCH-Carrier) ,,,,,,,, ,[, ..[ ]] [,[, ..
PAGE 288
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #CSURVC - Network Survey (Numeric Format) the BCCH Allocation list; the output of this information for nonserving cells depends on last #CSURVEXT setting: 1. if #CSURVEXT=0 this information is displayed only for serving cell 2. Not available about #CSURVEXT=1 or 2.. - decimal number; it is the arfcn of a valid channel in the BA list (n is in the range 1..
PAGE 289
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 290
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #CSURVC - Network Survey (Numeric Format) - number of scanned frequencies - number of found BCCh Example AT#CSURVC Network survey started… 48,24,-52,0.00,610,1,33281,3648,0,2,30 48,5,14 19 22 48 82 14,8 Network survey ended OK The command is executed within max. 2 minute. Note The information provided by #CSURVC is the same as that provided by #CSURV.
PAGE 291
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #CSURVU - Network Survey Of User Defined Channels Network survey ended Note 3.5.7.6.4. OK The command is executed within max. 2 minute. Network Survey Of User Defined Channels (Numeric Format) - #CSURVUC #CSURVUC - Network Survey Of User Defined Channels (Numeric Format) AT#CSURVUC=[ Execution command allows to perform a quick survey through the given [,[,… channels.
PAGE 292
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.6.5. BCCH Network Survey - #CSURVB #CSURVB - BCCH Network Survey AT#CSURVB= Execution command performs a quick network survey through M (maximum [] number of available frequencies depending on last selected band and RAT) channels. The survey stops as soon as BCCH carriers are found. The result format is like command #CSURV. AT#CSURVB=? Parameter: - number of desired BCCH carriers 1..
PAGE 293
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.6.7. Network Survey Format - #CSURVF #CSURVF - Network Survey Format AT#CSURVF= Set command controls the format of the numbers output by all the Easy [] Scan® Parameter: - numbers format 0 - Decimal 1 - Hexadecimal values, no text 2 - Hexadecimal values with text Read command reports the current number format, as follows: AT#CSURVF? AT#CSURVF=? 3.5.7.6.8.
PAGE 294
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 295
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #CSURVPC - PLMN Network Survey (Numeric Format) Parameter: - the desidered PLMN in numeric format AT#CSURVPC=? Test command returns OK Reproduction forbidden without Telit Communications S.p.A’s. written authorization - All Rights Reserved.
PAGE 296
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.7. GPS AT Commands Set (UC864-G only) 3.5.7.7.1. GPS Controller Power Management - $GPSP $GPSP - GPS Controller Power Management AT$GPSP= Set command allows to manage power-up or down of the GPS controller Parameter: 0 - GPS controller is powered down (default) 1 - GPS controller is powered up Note: the current setting is stored through $GPSSAV AT$GPSP? AT$GPSP=? Example 3.5.7.7.2.
PAGE 297
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 $GPSR - GPS Reset Example AT$GPSR=0 OK 3.5.7.7.3. GPS Antenna Type Definition - $GPSAT $GPSAT - GPS Antenna Type Definition AT$GPSAT= Set command selects the GPS antenna used. Parameter: 0 - GPS Antenna not power supplied by the module 1 - GPS Antenna power supplied by the module (default) Note: if current is 0, either $GPSAVand $GPSAIhave no meaning.
PAGE 298
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 299
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.7.6. Get Acquired Position - $GPSACP $GPSACP - Get Acquired Position AT$GPSACP Execution command returns information about the last GPS position in the format: $GPSACP: ,,,,, ,,,,, where: - UTC time (hhmmss.sss) referred to GGA sentence - format is ddmm.mmmm N/S (referred to GGA sentence) where: dd - degrees 00..90 mm.
PAGE 300
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 $GPSACP - Get Acquired Position 00..99 - 2000 to 2099 - nn - Total number of satellites in use (referred to GGA sentence) 00..12 AT$GPSACP? AT$GPSACP=? Example Reference 3.5.7.7.7. Read command has the same meaning as the Execution command Test command returns the OK result code AT$GPSACP $GPSACP:080220.479,4542.82691N,01344.26820E,259.07,3,2.1 ,0.1,0.0,0.
PAGE 301
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.8. SIM Toolkit AT Commands 3.5.7.8.1. SIM Tookit Interface Activation - #STIA #STIA - SIM Tookit Interface Activation AT#STIA= Set command is used to activate the SAT sending of unsolicited indications [ when a proactive command is received from SIM. [,]] Parameters: 0 - Disable SAT. is not required and will be ignored if given.
PAGE 302
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 303
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #STIA - SIM Tookit Interface Activation - (optional) text to be displayed to user In these cases neither #STGI nor #STSR commands are required:  AT#STGI is accepted anyway.  AT#STSR=,0 will answer OK but do nothing.
PAGE 304
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #STIA - SIM Tookit Interface Activation #STN: [,] where: - optional text string sent by SIM In this case:  AT#STSR=18,20 can be sent to end USSD transaction.  AT#STGI is accepted anyway.  AT#STSR=,0 will answer OK but do nothing.
PAGE 305
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #STIA - SIM Tookit Interface Activation startup) an unsolicited result code #STN: 254 is sent. The TA does not need to respond directly, i.e. AT#STSR is not required. It is possible to restart the SAT session from the main menu again with the command AT#STGI=37. Note: The settings are saved on user profile and available on following reboot. SIM Toolkit activation/deactivation is only performed at power on.
PAGE 306
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #STIA - SIM Tookit Interface Activation command is issued (see #STSGI) and after the SAT main menu has been displayed on TE an AT#STSR=37,0,x command is issued to select an item in the menu (see #STSR) 3.5.7.8.2. SIM Tookit Get Information - #STGI #STGI - SIM Tookit Get Information AT#STGI= #STGI set command is used to request the parameters of a proactive [] command from the ME.
PAGE 307
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.
PAGE 308
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #STGI - SIM Tookit Get Information 0 - normal priority 1 - high priority bits 2 to 7: reserved for future use bit 8: 0 - clear message after a delay 1 - wait for user to clear message - text to be displayed to user if =34 (GET INKEY) #STGI: ,, where: - unsigned Integer used as a bit field. 0..
PAGE 309
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #STGI - SIM Tookit Get Information 1 - Alphabet set bit 2: 0 - SMS default alphabet (GSM character set) 1 - UCS2 alphabet bit 3: 0 - ME may echo user input on the display 1 - User input shall not be revealed in any way. Hidden entry mode (see 3GPP TS 31.114) is only available when using digit input. In hidden entry mode only characters (‘0’-‘9’, ‘*’ and ‘#‘) are allowed.
PAGE 310
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #STGI - SIM Tookit Get Information 1 - Presentation as a choice of navigation options if bit 1 is '1' bit 3: 0 - No selection preference 1 - Selection using soft key preferred bits 4 to 7: 0 bit 8: 0 - No help information available 1 - Help information available - number of items in the list - string giving menu title - item identifier 1..
PAGE 311
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #STGI - SIM Tookit Get Information 1.. - title of item - the next proactive command type to be issued upon execution of the menu item. 0 - no next action information available. Note: upon receiving the #STGI response, the TA must send #STSR command (see below) to confirm the execution of the proactive command and provide any required user response, e.g. selected menu item.
PAGE 312
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #STGI - SIM Tookit Get Information 3.5.7.8.3. SIM Tookit Send Response - #STSR #STSR - SIM Tookit Send Response The write command is used to provide to SIM user response to a command AT#STSR= and any required user information, e.g. a selected menu item. [, [,]] Parameters: - integer type; proactive command ID according to 3GPP TS 31.
PAGE 313
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #STSR - SIM Tookit Send Response Use of icons is not supported. All icon related actions will respond with no icon available. AT#STSR? The read command can be used to request the currently ongoing proactive command and the SAT state in the format #STSR: , where: - SAT interface state (see #STIA) - ongoing proactive command An error message will be returned if there is no pending command.
PAGE 314
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 #JDR - Jammed Detect & Report JAMMED - Jammed condition detected OPERATIVE - Normal Operating condition restored. This code will be shown only after a jammed condition has occurred. 3 - enables the Jammed Detect; the MODULE will make both the actions as for =1 and =2.
PAGE 315
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.10. SAP AT Commands Set 3.5.7.10.1. Remote SIM Enable - #RSEN #RSEN – Remote SIM Enable AT#RSEN=[, Set command is used to enable/disable the Remote SIM feature.
PAGE 316
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 3.5.7.11. OTA AT Commands Set 3.5.7.11.1.
PAGE 317
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev. 7 - 2010-10-14 4.
PAGE 318
UC864-E/G/WD/WDU AT Commands Reference Guide 80304ST10041a Rev.