Specifications

Ū90mm(3.54in.)
ELECTROMAGNETIC BRAKE MOTOR
(Power off activated type)
40W
ū Motor Specification - 30min. Rating (Continuous : F2 fan)
ū Permissible Torque When using gearhead
ELECTROMAG
NETIC BRAKE
LEAD WIRE TYPE MOTOR
TERMINAL BOX TYPE MOTOR
BRAKE 40W
ҊEnter the ĸPhase & VoltageĹcode in the box(Ū) within the motor model name.
ҊĸPinion ShaftĹis for attaching gearhead and ĸD-Cut ShaftĹis for using motor only.
: Contains a built-in thermal protector. If a motor overheats for any reason the thermal protector opened and the motor stops. When the motor temperature
drops, the thermal protector closes and the motor restarts. Be sure to turn the motor off before inspecting. By attaching F2 FAN additionally, temperature
reducing of over 10œ could be available.
TP
ҊEnter the gear ratio in the box (Ū) within the gearhead model name. A colored background indicates gear shaft rotation in the same direction
as the motor shaft ; a white background indicates rotation in the opposite direction.
ҊThe speed is calculated by dividing the motorĹs synchronous speed (50Hz : 1500 r/min, 60 Hz : 1800 r/min) by the gear ratio.
ҊThe actual speed is 2~20% less than the displayed value, depending on the size of the load.
ҊIf more slow speed is needed than above value, use decimal gearhead with a gear ratio of 10:1 could be used between general gearhead and
motor. Even in this case, just speed will be reduced without increase in permissible torque; the maximum permissible torque is 100kgfcm
(10N.m, 88lb-in).
Lead Wire Type
9BDG(D)A-40G
9BDG(D)B-40G
9BDG(D)C-40G
9BDG(D)D-40G
9BDG(D)E-40G
9BDG(D)F-40G
9BDG(D)G-40G
9BDG(D)H-40G
9BDG(D)I-40G
9BDG(D)J-40G
9BDG(D)K-40G
9BDG(D)L-40G
9BDG(D)M-40G
9BDG(D)N-40G
9BDG(D)O-40G
9BDG(D)A-40G-T
9BDG(D)B-40G-T
9BDG(D)C-40G-T
9BDG(D)D-40G-T
9BDG(D)E-40G-T
9BDG(D)F-40G-T
9BDG(D)G-40G-T
9BDG(D)H-40G-T
9BDG(D)I-40G-T
9BDG(D)J-40G-T
9BDG(D)K-40G-T
9BDG(D)L-40G-T
9BDG(D)M-40G-T
9BDG(D)N-40G-T
9BDG(D)O-40G-T
1/19
30min
30min
30min
30min
30min
Single Phase 110
Single Phase 115
Single Phase 220
Single Phase 220
Single Phase 230
Single Phase 230
Three phase 220
Three phase 220
Three phase 230
Three phase 230
Three phase 380
Three phase 380
Three phase 440
Three phase 440
Three phase 440
60
60
50
60
50
60
50
60
50
60
50
60
50
50
60
1.0
1600 160 23 2600 260 37 1550 16 250
4.0 400
2000 200 28
2600 260 37
2600 260 37
2600 260 37
3120 312 44 1300
2600 260 37 1550
3120 312 44 1300
2600 260 37 1550
- -
3120 312 44 1300
2600 260 37 1550
3120 312 44 1300
2600 260 37 1550
- -
3120 312 44 1300
2600 260 37 1550
- -
3120 312 44 1300
3120 312 44 1300
2600 260 37 1550
0.5
0.42
0.22
0.18
Output
Starting
Time
HP
W
VAC
Hz
r/min VAC
ל
A
mN.mgfcm oz-in mN.mgfcm oz-in
Voltage
Starting Torque
Rated Torque
Capacitor
Rated
Speed
Freq.
Curre
nt
40
Terminal Box Type
Model
9BDGŪ-40G : Pinion Shaft Type
9BDDŪ-40 : D-Cut Shaft Type
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
60Hz
900 600 500 360 300 240 200 180 144 120 100 72 60 50 45 36 30 24 20 18
2 3 3.6 5 6 7.5 9 10 12.5 15 18 25 30 36 40 50 60 75 90 100
5.0 6.8 8.2 11.3 13.6 17.0 20.4 22.7 28.4 34.0 40.8 51.1 61.3 73.6 81.5 100 100 100 100 100
0.50 0.68 0.82 1.13 1.36 1.70 2.04 2.27 2.84 3.40 4.08 5.11 6.1 7.4 8.2 10 10 10 10 10
4.4 6.0 7.2 10.0 12.0 15.0 18.0 20.0 25.1 30.0 36.0 45.1 54.1 65.0 72.0 88 88 88 88 88
15 12 10
120 150 180
100 100 100
10 10 10
88 88 88
9GBKŪMH
9BDGŪ-40G
speed RPM (r/min)
Gear Ratio
Model
Motor/Gearhead
kgf cm
N.m
lb-in
50Hz
750 500 417 300 250 200 167 150 120 100 83 60 50 42 38 30 25 20 17 15
2 3 3.6 5 6 7.5 9 10 12.5 15 18 25 30 36 40 50 60 75 90 100
6.0 8.3 9.9 13.8 16.5 20.7 24.8 27.5 34.4 41.3 49.6 62.1 74.5 89.4 99.1 100 100 100 100 100
0.60 0.83 0.99 1.38 1.65 2.07 2.48 2.75 3.44 4.13 4.96 6.21 7.5 8.9 9.9 10 10 10 10 10
5.3 7.3 8.7 12.2 14.6 18.3 21.9 24.3 30.4 36.5 43.8 54.8 65.8 78.9 87.5 88 88 88 88 88
13 10 8
120 150 180
100 100 100
10 10 10
88 88 88
9GBKŪMH
9BDGŪ-40G
speed RPM (r/min)
Gear Ratio
Model
Motor/Gearhead
kgf cm
N.m
lb-in