Specifications

Ū
90mm(3.54in.)
REVERSIBLE MOTOR
120W
ҊEnter the gear ratio in the box (Ū) within the gearhead model name. A colored background indicates gear shaft rotation in the same direction
as the motor shaft ; a white background indicates rotation in the opposite direction.
ҊThe speed is calculated by dividing the motorĹs synchronous speed (50Hz : 1500 r/min, 60 Hz : 1800 r/min) by the gear ratio.
ҊThe actual speed is 2~20% less than the displayed value, depending on the size of the load.
ҊIf more slow speed is needed than above value, use decimal gearhead with a gear ratio of 10:1 could be used between general gearhead and
motor. Even in this case, just speed will be reduced without increase in permissible torque; the maximum permissible torque is 200kgfcm (P
type) / 300kgfcm (H type).
ū Permissible Torque When using gearhead
ū Motor Specification - 30min. Rating (Continuous : F2 fan)
LEAD WIRE TYPE MOTOR
+ PB TYPE GEARHEAD
LEAD WIRE TYPE MOTOR
+ PF TYPE GEARHEAD
TERMINAL BOX TYPE MOTOR
+ PF TYPE GEARHEAD
LEAD WIRE TYPE MOTOR
+ HB TYPE GEARHEAD
ҊEnter the ĸPhase & VoltageĹcode in the box(Ū) within the motor model name.
ҊĸPinion ShaftĹis for attaching gearhead and ĸD-Cut ShaftĹis for using motor only.
: Contains a built-in thermal protector. If a motor overheats for any reason the thermal protector opened and the motor stops. When the
motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor off before inspecting. By
attaching F2 FAN additionally, temperature reducing of over 10œ could be available.
TP
TP
TP
TP
TP
TP
TP
Lead Wire Type
9RDG(D)A-120FP(H)
9RDG(D)B-120FP(H)
9RDG(D)C-120FP(H)
9RDG(D)D-120FP(H)
9RDG(D)E-120FP(H)
9RDG(D)F-120FP(H)
9RDG(D)A-120FP(H)-T
9RDG(D)B-120FP(H)-T
9RDG(D)C-120FP(H)-T
9RDG(D)D-120FP(H)-T
9RDG(D)E-120FP(H)-T
9RDG(D)F-120FP(H)-T
1/6
Single Phase 110
Single Phase 115
Single Phase 220
Single Phase 220
Single Phase 230
Single Phase 230
60
60
50
60
50
60
2.5
7000 700 99 7600 760 108 1500 30 250
6.5 400
7000 700 99
9120 912 129 1300
7600 760 108 1500
9120 912 129 1300
7600 760 108 1500
1.3
Output
HP
W
VAC
Hz
r/min VAC
ל
A
mN.mgfcm oz-in mN.mgfcm oz-in
Voltage
Starting Torque
Rated Torque
Capacitor
Rated
Speed
Freq.
Current
120
Terminal Box Type
Model
9RDGŪ-120FP(H) : Pinion Shaft Type
9RDDŪ-120F : D-Cut Shaft Type
60Hz
15 12 10
120 150 180
200 200 200
20 20 20
177 177 177
300 300 300
30 30 30
265 265 265
900 600 500 360 300 240 200 144 120 100 90 72 60 50 45 36 30 24 20 18
2 3 3.6 5 6 7.5 9 12.5 15 18 20 25 30 36 40 50 60 75 90 100
17.5 18.7 22.5 31.2 37.4 46.8 56.1 70.2 84.2 101 114 126 152 182 200 200 200 200 200 200
1.8 1.9 2.3 3.1 3.7 4.7 5.6 7.0 8.4 10.1 11.4 12.6 15 18 20 20 20 20 20 20
15.5 16.5 19.9 27.5 33.0 41.3 49.5 62.0 74 89 101 111 134 161 177 177 177 177 177 177
- 20.6 24.8 - 41.1 - 61.7 77.2 93 111 - 139 167 200 - 220 240 300 300 300
- 2.1 2.5 - 4.1 - 6.2 7.7 9.3 11.1 - 13.9 16.7 20.2 - 22 24 30 30 30
- 18.2 21.9 - 36.3 - 54.5 68.2 81.8 98.1 - 122 148 177 - 194 212 265 265 265
9PBKŪBH
9PFKŪBH
9HBKŪBH
9RDGŪ-120FP
9RDGŪ-120FH
speed RPM (r/min)
Gear Ratio
Model
Motor/Gearhead
kgf cm
N.m
lb-in
kgf cm
N.m
lb-in
50Hz
13 10 8
120 150 180
200 200 200
20 20 20
177 177 177
300 300 300
30 30 30
265 265 265
750 500 417 300 250 200 167 120 100 83 75 60 50 42 38 30 25 20 17 15
2 3 3.6 5 6 7.5 9 12.5 15 18 20 25 30 36 40 50 60 75 90 100
22.0 23.2 27.8 38.7 46.4 58.0 69.6 87.0 104 125 140 156 188 200 200 200 200 200 200 200
2.20 2.32 2.78 3.87 4.64 5.80 6.96 8.7 10.4 12.5 14.0 15.6 19 20 20 20 20 20 20 20
19.4 20.5 24.5 34.2 41.0 51.2 61.5 76.8 92 110 124 138 166 177 177 177 177 177 177 177
- 25.5 30.6 - 51.0 - 76.6 95.7 114 138 - 172 207 220 - 240 260 300 300 300
- 2.6 3.1 - 5.1 - 7.7 9.6 11.4 13.8 - 17.2 20.7 22 - 24 26 30 30 30
- 22.5 27.0 - 45.1 - 67.6 84.5 101 121 - 152 183 194 - 212 230 265 265 265
9PBKŪBH
9PFKŪBH
9HBKŪBH
9RDGŪ-120FP
9RDGŪ-120FH
speed RPM (r/min)
Gear Ratio
Model
Motor/Gearhead
kgf cm
N.m
lb-in
kgf cm
N.m
lb-in
REVERSIBLE 120W