Specifications
Ū
90mm(3.54in.)
REVERSIBLE MOTOR
40W
ū
Permissible Torque When using gearhead
ū
Motor Specification - 30min. Rating (Continuous : F2 fan)
REVERSIBLE 40W
LEAD WIRE TYPE MOTOR TERMINAL BOX TYPE MOTOR
ҊEnter the ĸPhase & VoltageĹcode in the box(Ū) within the motor model name.
ҊĸPinion ShaftĹis for attaching gearhead and ĸD-Cut ShaftĹis for using motor only.
: Contains a built-in thermal protector. If a motor overheats for any reason the thermal protector opened and the motor stops. When the
motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor off before inspecting. By
attaching F2 FAN additionally, temperature reducing of over 10œ could be available.
TP
ҊEnter the gear ratio in the box (Ū) within the gearhead model name. A colored background indicates gear shaft rotation in the same direction
as the motor shaft ; a white background indicates rotation in the opposite direction.
ҊThe speed is calculated by dividing the motorĹs synchronous speed (50Hz : 1500 r/min, 60 Hz : 1800 r/min) by the gear ratio.
ҊThe actual speed is 2~20% less than the displayed value, depending on the size of the load.
ҊIf more slow speed is needed than above value, use decimal gearhead with a gear ratio of 10:1 could be used between general gearhead and
motor. Even in this case, just speed will be reduced without increase in permissible torque; the maximum permissible torque is 100kgfcm
(10N.m, 88lb-in).
TP
TP
TP
TP
TP
TP
Lead Wire Type
9RDG(D)A-40G
9RDG(D)B-40G
9RDG(D)C-40G
9RDG(D)D-40G
9RDG(D)E-40G
9RDG(D)F-40G
9RDG(D)A-40G-T
9RDG(D)B-40G-T
9RDG(D)C-40G-T
9RDG(D)D-40G-T
9RDG(D)E-40G-T
9RDG(D)F-40G-T
1/15
Single Phase 110
Single Phase 115
Single Phase 220
Single Phase 220
Single Phase 230
Single Phase 230
60
60
50
60
50
60
1.0
2600 260 37 2600 260 37 1550 16.0 250
4.0 400
2600 260 37
3000 300 42 1350
2600 260 37 1550
3000 300 42 1350
2600 260 37 1550
0.5
Output
HP
W
VAC
Hz
r/min VAC
ל
A
mN.mgfcm oz-in
mN.m
gfcm oz-in
Voltage
Starting Torque
Rated Torque
Capacitor
Rated
Speed
Freq.
Current
40
Terminal Box Type
Model
9RDGŪ-40G : Pinion Shaft Type
9RDDŪ-40 : D-Cut Shaft Type
60Hz
900 600 500 360 300 240 200 180 144 120 100 72 60 50 45 36 30 24 20 18
2 3 3.6 5 6 7.5 9 10 12.5 15 18 25 30 36 40 50 60 75 90 100
5.0 6.8 8.2 11.3 13.6 17.0 20.4 22.7 28.4 34.0 40.8 51.1 61.3 73.6 81.5 100 100 100 100 100
0.50 0.68 0.82 1.13 1.36 1.70 2.04 2.27 2.84 3.40 4.08 5.11 6.1 7.4 8.2 10 10 10 10 10
4.4 6.0 7.2 10.0 12.0 15.0 18.0 20.0 25.1 30.0 36.0 45.1 54.1 65.0 72.0 88 88 88 88 88
15 12 10
120 150 180
100 100 100
10 10 10
88 88 88
9GBKŪMH
9RDGŪ-40G
speed RPM (r/min)
Gear Ratio
Model
Motor/Gearhead
kgf cm
N.m
lb-in
50Hz
750 500 417 300 250 200 167 150 120 100 83 60 50 42 38 30 25 20 17 15
2 3 3.6 5 6 7.5 9 10 12.5 15 18 25 30 36 40 50 60 75 90 100
6.0 8.3 9.9 13.8 16.5 20.7 24.8 27.5 34.4 41.3 49.6 62.1 74.5 89.4 99.1 100 100 100 100 100
0.60 0.38 0.99 1.38 1.65 2.07 2.48 2.75 344 4.13 4.96 6.21 7.5 8.9 9.9 10 10 10 10 10
5.3 7.3 8.7 12.2 14.6 18.3 21.9 24.3 30.4 36.5 43.8 54.8 65.8 78.9 87.5 88 88 88 88 88
13 10 8
120 150 180
100 100 100
10 10 10
88 88 88
9GBKŪMH
9RDGŪ-40G
speed RPM (r/min)
Gear Ratio
Model
Motor/Gearhead
kgf cm
N.m
lb-in