Specifications

Ū
90mm(3.54in.)
INDUCTION MOTOR
180W
Permissible Torque When using gearhead
ҊEnter the gear ratio in the box (Ū) within the gearhead model name. A colored background indicates gear shaft rotation in the same direction
as the motor shaft ; a white background indicates rotation in the opposite direction.
ҊThe speed is calculated by dividing the motorĹs synchronous speed (50Hz : 1500 r/min, 60 Hz : 1800 r/min) by the gear ratio.
ҊThe actual speed is 2~20% less than the displayed value, depending on the size of the load.
ҊIf more slow speed is needed than above value, use decimal gearhead with a gear ratio of 10:1 could be used between general gearhead and
motor. Even in this case, just speed will be reduced without increase in permissible torque; the maximum permissible torque is 200kgfcm (P
type) / 300kgfcm (H type).
Motor Specification
LEAD WIRE TYPE MOTOR
+ PB TYPE GEARHEAD
LEAD WIRE TYPE MOTOR
+ PF TYPE GEARHEAD
TERMINAL BOX TYPE MOTOR
+ PF TYPE GEARHEAD
LEAD WIRE TYPE MOTOR
+ HB TYPE GEARHEAD
ҊEnter the ĸPhase & VoltageĹcode in the box(Ū) within the motor model name.
ҊĸPinion ShaftĹis for attaching gearhead and ĸD-Cut ShaftĹis for using motor only.
: Contains a built-in thermal protector. If a motor overheats for any reason the thermal protector opened and the motor stops. When the
motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor off before inspecting.
TP
TP
TP
TP
TP
Lead Wire Type
9IDG(D)C-180FP(H)
9IDG(D)D-180FP (H)
9IDG(D)E-180FP (H)
9IDG(D)F-180FP (H)
9IDG(D)C-180FP(H)-T
9IDG(D)D-180FP(H)-T
9IDG(D)E-180FP(H)-T
9IDG(D)F-180FP(H)-T
Single Phase 220
Single Phase 220
Single Phase 230
Single Phase 230
50
60
50
60
1.40
13500 1350 191 1300
7000 700 99
11300 1130 108 1550
6.5 400
13500 1350 191 1300
11300 1130 108 1550
Output
HP
W
VAC
Hz
r/min VAC
ל
A
mN.mgfcm oz-in mN.mgfcm oz-in
Voltage
Starting Torque
Rated Torque
Capacitor
Rated
Speed
Freq.
Current
1801/4
Terminal Box Type
Model
9IDGŪ-180FP(H) : Pinion Shaft Type
9IDDŪ-180F : D-Cut Shaft Type
60Hz
900 600 500 360 300 240 200 144 120 100 90 72 60 50 45 36 30 24 20 18
2 3 3.6 5 6 7.5 9 12.5 15 18 20 25 30 36 40 50 60 75 90 100
22 27 32 45 54 67 80 100 120 152 171 189 200 200 200 200 200 200 200 200
2.2 2.7 3.2 4.5 5.4 6.7 8.0 10 12 15 17 19 20 20 20 20 20 20 20 20
19 24 29 39 48 60 71 88 106 134 151 167 177 177 177 177 177 177 177 177
15 12 10
120 150 180
200 200 200
20 20 20
177 177 177
300 300 300 300 300 300 300 300
30 30 30 30 30 30 30 30
265 265 265 265 265 265 265 265
- 28 34 - 57 - 84 105 126 160 - 210 227 273 -
- 2.8 3.4 - 5.7 - 8.4 11 13 16 - 21 23 27 -
- 25 30 - 50 - 74 93 111 141 - 185 200 241 -
9PBK
Ū
BH
9PFK
Ū
BH
9HBK
Ū
BH
9IDG2-180FP
9IDG2-180FH
speed RPM (r/min)
Gear Ratio
Model
Motor/Gearhead
kgf cm
N.m
lb-in
kgf cm
N.m
lb-in
50Hz
750 500 417 300 250 200 167 120 100 83 75 60 50 42 38 30 25 20 17 15
2 3 3.6 5 6 7.5 9 12.5 15 18 20 25 30 36 40 50 60 75 90 100
25 32 39 54 65 81 97 122 145 200 200 200 200 200 200 200 200 200 200 200
2.5 3.2 3.9 5.4 6.5 8.1 9.7 12 15 19 20 20 20 20 20 20 20 20 20 20
22 29 34 48 57 71 86 107 128 168 177 177 177 177 177 177 177 177 177 177
13 10 8
120 150 180
200 200 200
20 20 20
177 177 177
300 300 300 300 300 300 300 300
30 30 30 30 30 30 30 30
265 265 265 265 265 265 265 265
- 34 41 - 68 - 105 128 153 200 - 230 287 300 -
- 3.4 4.1 - 6.8 - 10.5 13 15 20 - 23 28 30 -
- 30 36 - 60 - 90 113 135 177 - 203 245 265 -
9PBK
Ū
BH
9PFK
Ū
BH
9HBKŪBH
9IDGC-180FP
9IDGC-180FH
speed RPM (r/min)
Gear Ratio
Model
Motor/Gearhead
kgf cm
N.m
lb-in
kgf cm
N.m
lb-in
INDUCTION 180W