Specifications

Ū
90mm(3.54in.)
INDUCTION MOTOR
150W
Motor Specification
Permissible Torque When using gearhead
ҊEnter the gear ratio in the box (Ū) within the gearhead model name. A colored background indicates gear shaft rotation in the same direction
as the motor shaft ; a white background indicates rotation in the opposite direction.
ҊThe speed is calculated by dividing the motorĹs synchronous speed (50Hz : 1500 r/min, 60 Hz : 1800 r/min) by the gear ratio.
ҊThe actual speed is 2~20% less than the displayed value, depending on the size of the load.
ҊIf more slow speed is needed than above value, use decimal gearhead with a gear ratio of 10:1 could be used between general gearhead and
motor. Even in this case, just speed will be reduced without increase in permissible torque; the maximum permissible torque is 200kgfcm (P
type) / 300kgfcm (H type).
LEAD WIRE TYPE MOTOR
+ PB TYPE GEARHEAD
LEAD WIRE TYPE MOTOR
+ PF TYPE GEARHEAD
TERMINAL BOX TYPE MOTOR
+ PF TYPE GEARHEAD
LEAD WIRE TYPE MOTOR
+ HB TYPE GEARHEAD
ҊEnter the ĸPhase & VoltageĹcode in the box(Ū) within the motor model name.
ҊĸPinion ShaftĹis for attaching gearhead and ĸD-Cut ShaftĹis for using motor only.
: Contains a built-in thermal protector. If a motor overheats for any reason the thermal protector opened and the motor stops. When the
motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor off before inspecting.
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
Lead Wire Type
9IDG(D)G-150FP(H)
9IDG(D)H-150FP
(H)
9IDG(D)I-150FP (H)
9IDG(D)J-150FP (H)
9IDG(D)K-150FP (H)
9IDG(D)L-150FP (H)
9IDG(D)M-150FP (H)
9IDG(D)N-150FP (H)
9IDG(D)O-150FP (H)
9IDG(D)G-150FP(H)-T
9IDG(D)H-150FP(H)-T
9IDG(D)I-150FP(H)-T
9IDG(D)J-150FP(H)-T
9IDG(D)K-150FP(H)-T
9IDG(D)L-150FP(H)-T
9IDG(D)M-150FP(H)-T
9IDG(D)N-150FP(H)-T
9IDG(D)O-150FP(H)-T
1/5
Three phase 220
Three phase 220
Three phase 230
Three phase 230
Three phase 380
Three phase 380
Three phase 400
Three phase 440
Three phase 440
50
60
50
60
50
60
50
50
60
1.02
11000 1100 156 1300
11400 1140 161
9300 930 132 1550
ʳ ʳ
11000 1100 156 1300
9300 930 132 1550
11400 1140 161
11000 1100 156 1300
ʳ ʳ
9300 930 132 1550
11000 1100 156 1300
11400 1140 161 11000 1100 156 1300 ʳ ʳ
9300 930 132 1550
0.66
0.54
Output
HP
W
VAC
Hz
r/min VAC
ל
A
mN.mgfcm oz-in mN.mgfcm oz-in
Voltage
Starting Torque
Rated Torque
Capacitor
Rated
Speed
Freq.
Current
150
Terminal Box Type
Model
9IDGŪ-150FP(H) : Pinion Shaft Type
9IDDŪ-150F : D-Cut Shaft Type
60Hz
900 600 500 360 300 240 200 144 120 100 90 72 60 50 45 36 30 24 20 18
2 3 3.6 5 6 7.5 9 12.5 15 18 20 25 30 36 40 50 60 75 90 100
19 23.2 27.8 38.7 46.4 58.0 69.6 87 104 125 135 156 188 200 200 200 200 200 200 200
1.9 2.3 2.8 3.9 4.6 5.8 7.0 8.7 10.4 12.5 13.5 15.6 19 20 20 20 20 20 20 20
17 20 25 34 41 51 61 77 92 110 119 138 166 177 177 177 177 177 177 177
15 12 10
120 150 180
200 200 200
20 20 20
177 177 177
300 300 300 300 300 300 300 300
30 30 30 30 30 30 30 30
265 265 265 265 265 265 265 265
- 25.5 30.6 - 51.0 - 76.6 96 114 138 - 172 207 225 -
- 2.6 3.1 - 5.1 - 7.7 9.6 11.4 13.8 - 17.2 20.7 23 -
- 23 27 - 45 - 68 85 101 121 - 152 183 199 -
9PBK
Ū
BH
9PFK
Ū
BH
9HBKŪBH
9IDG
Ū
-150FP
9IDGŪ-150FH
speed RPM (r/min)
Gear Ratio
Model
Motor/Gearhead
kgf cm
N.m
lb-in
kgf cm
N.m
lb-in
50Hz
750 500 417 300 250 200 167 120 100 83 75 60 50 42 38 30 25 20 17 15
2 3 3.6 5 6 7.5 9 12.5 15 18 20 25 30 36 40 50 60 75 90 100
24 29 34 48 58 72 86 108 129 155 167 193 200 200 200 200 200 200 200 200
2.4 2.9 3.4 4.8 5.8 7.2 8.6 10.8 12.9 15.5 16.7 19.3 20 20 20 20 20 20 20 20
21 25 30 42 51 64 76 95 114 137 148 171 177 177 177 177 177 177 177 177
13 10 8
120 150 180
200 200 200
20 20 20
177 177 177
300 300 300 300 300 300 300 300
30 30 30 30 30 30 30 30
265 265 265 265 265 265 265 265
- 31.6 37.9 - 63.3 - 94.9 119 142 171 - 213 220 250 -
- 3.2 3.8 - 6.3 - 9.5 11.9 14.2 17.1 - 21 22 25 -
- 28 33 - 56 - 84 105 125 151 - 188 194 221 -
9PBK
Ū
BH
9PFK
Ū
BH
9HBK
Ū
BH
9IDG
Ū
-150FP
9IDG
Ū
-150FH
speed RPM (r/min)
Gear Ratio
Model
Motor/Gearhead
kgf cm
N.m
lb-in
kgf cm
N.m
lb-in