Specifications

Ū90mm(3.54in.)
INDUCTION MOTOR
60W
LEAD WIRE TYPE MOTOR
+ PB TYPE GEARHEAD
LEAD WIRE TYPE MOTOR
+ PF TYPE GEARHEAD
TERMINAL BOX TYPE MOTOR
+ PF TYPE GEARHEAD
ҊEnter the gear ratio in the box (Ū) within the model name. A colored background indicates gear shaft rotation in the same direction as the
motor shaft ; a white background indicates rotation in the opposite direction.
ҊThe speed is calculated by dividing the motor's synchronous speed (50Hz : 1500 r/min, 60 Hz : 1800 r/min) by the gear ratio.
ҊThe actual speed is 2~20% less than the displayed value, depending on the size of the load.
ҊIf more slow speed is needed than above value, use decimal gearhead with a gear ratio of 10:1 could be used between general gearhead and
motor. Even in this case, just speed will be reduced without increase in permissible torque; the maximum permissible torque is 200kgfcm
(20N.m, 177lb-in).
Permissible Torque When using gearhead
Motor Specification
ҊEnter the ĸPhase & VoltageĹcode in the box(Ū) within the motor model name.
ҊĸPinion ShaftĹis for attaching gearhead and ĸD-Cut ShaftĹis for using motor only.
: Contains a built-in thermal protector. If a motor overheats for any reason the thermal protector opened and the motor stops. When the
motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor off before inspecting.
TP
Lead Wire Type
9IDG(D)A-60FP
9IDG(D)B-60FP
9IDG(D)C-60FP
9IDG(D)D-60FP
9IDG(D)E-60FP
9IDG(D)F-60FP
9IDG(D)G-60FP
9IDG(D)H-60FP
9IDG(D)I-60FP
9IDG(D)J-60FP
9IDG(D)K-60FP
9IDG(D)L-60FP
9IDG(D)M-60FP
9IDG(D)N-60FP
9IDG(D)O-60FP
9IDG(D)A-60FP-T
9IDG(D)B-60FP-T
9IDG(D)C-60FP-T
9IDG(D)D-60FP-T
9IDG(D)E-60FP-T
9IDG(D)F-60FP-T
9IDG(D)G-60FP-T
9IDG(D)H-60FP-T
9IDG(D)I-60FP-T
9IDG(D)J-60FP-T
9IDG(D)K-60FP-T
9IDG(D)L-60FP-T
9IDG(D)M-60FP-T
9IDG(D)N-60FP-T
9IDG(D)O-60FP-T
1/12
Single Phase 110
Single Phase 115
Single Phase 220
Single Phase 220
Single Phase 230
Single Phase 230
Three phase 220
Three phase 220
Three phase 230
Three phase 230
Three phase 380
Three phase 380
Three phase 400
Three phase 440
Three phase 440
60
60
50
60
50
60
50
60
50
60
50
60
50
50
60
1.20
3000 300 42 3800 380 54 1550 16 250
4.0 400
- -
- -
- -
3000 300 42
4560 456 65 1300
3800 380 54 1550
4560 456 65 1300
3800 380 54 1550
5000 500 71
5000 500 71
4560 456 65 1300
3800 380 54 1550
4560 456 65 1300
3800 380 54 1550
4560 456 65 1300
3800 380 54 1550
5000 500 71
4560 456 65 1300
4560 456 65 1300
3800 380 54 1550
0.60
0.60
0.38
0.27
Output
HP
W
VAC
Hz
r/min VAC
ל
A
mN.mgfcm oz-in mN.mgfcm oz-in
Voltage
Starting Torque
Rated Torque
Capacitor
Rated
Speed
Freq.
Current
60
Terminal Box Type
Model
9IDGŪ-60FP : Pinion Shaft Type
9IDDŪ-60F : D-Cut Shaft Type
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
60Hz
900 600 500 360 300 240 200 144 120 100 90 72 60 50 45 36 30 24 20 18
2 3 3.6 5 6 7.5 9 12.5 15 18 20 25 30 36 40 50 60 75 90 100
7.5 9.7 11.7 16.2 19.4 24.3 29.2 36.5 43.8 52.6 59.0 66.0 79.2 95 106 132 158 177 200 200
0.8 1.0 1.2 1.6 1.9 2.4 2.9 3.7 4.4 5.3 5.9 6.6 7.9 9.5 10.6 13.2 15.8 17.7 20 20
6.6 8.6 10 14 17 21 26 32 39 46 52 58 70 84 94 117 140 156 177 177
15 12 10
120 150 180
200 200 200
20 20 20
177 177 177
9PBK
Ū
BH
9PFK
Ū
BH
9IDG
Ū
-60FP
speed RPM (r/min)
Gear Ratio
Model
Motor/Gearhead
kgf cm
N.m
lb-in
50Hz
750 500 417 300 250 200 167 120 100 83 75 60 50 42 38 30 25 20 17 15
2 3 3.6 5 6 7.5 9 12.5 15 18 20 25 30 36 40 50 60 75 90 100
10.0 12.2 14.6 20.3 24 30 37 46 55 66 72 83 99 119 132 165 198 200 200 200
1.0 1.2 1.5 2.0 2.4 3.0 3.7 4.6 5.5 6.6 7.2 8.3 9.9 11.9 13.2 16.5 20 20 20 20
8.8 10.8 12.9 17.9 21.5 26.8 32.2 40.3 48.4 58.0 63.6 72.8 87 105 117 146 175 177 177 177
13 10 8
120 150 180
200 200 200
20 20 20
177 177 177
9PBK
Ū
BH
9PFK
Ū
BH
9IDG
Ū
-60FP
speed RPM (r/min)
Gear Ratio
Model
Motor/Gearhead
kgf cm
N.m
lb-in