Specifications

Ū
90mm(3.54in.)
INDUCTION MOTOR
40W
LEAD WIRE TYPE MOTOR
+ BOX TYPE GEARHEAD
TERMINAL BOX TYPE MOTOR
+ BOX TYPE GEARHEAD
Ҋ Enter the gear ratio in the box (Ū) within the model name. A colored background indicates gear shaft rotation in the same direction as the
motor shaft ; a white background indicates rotation in the opposite direction.
ҊThe speed is calculated by dividing the motor's synchronous speed (50Hz : 1500 r/min, 60 Hz : 1800 r/min) by the gear ratio.
ҊIf more slow speed is needed than above value, use decimal gearhead with a gear ratio of 10:1 could be used between general gearhead and
motor. Even in this case, just speed will be reduced without increase in permissible torque; the maximum permissible torque is 100kgfcm
(10N.m, 88lb-in).
Permissible Torque When using gearhead
Motor Specification
ҊEnter the ĸPhase & VoltageĹcode in the box(Ū) within the motor model name.
ҊĸPinion ShaftĹis for attaching gearhead and ĸD-Cut ShaftĹis for using motor only.
: Contains a built-in thermal protector. If a motor overheats for any reason the thermal protector opened and the motor stops. When the
motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor off before inspecting.
TP
Lead Wire Type
9IDG(D)A-40G
9IDG(D)B-40G
9IDG(D)C-40G
9IDG(D)D-40G
9IDG(D)E-40G
9IDG(D)F-40G
9IDG(D)G-40G
9IDG(D)H-40G
9IDG(D)I-40G
9IDG(D)J-40G
9IDG(D)K-40G
9IDG(D)L-40G
9IDG(D)M-40G
9IDG(D)N-40G
9IDG(D)O-40G
9IDG(D)A-40G-T
9IDG(D)B-40G-T
9IDG(D)C-40G-T
9IDG(D)D-40G-T
9IDG(D)E-40G-T
9IDG(D)F-40G-T
9IDG(D)G-40G-T
9IDG(D)H-40G-T
9IDG(D)I-40G-T
9IDG(D)J-40G-T
9IDG(D)K-40G-T
9IDG(D)L-40G-T
9IDG(D)M-40G-T
9IDG(D)N-40G-T
9IDG(D)O-40G-T
1/15
Single Phase 110
Single Phase 115
Single Phase 220
Single Phase 220
Single Phase 230
Single Phase 230
Three phase 220
Three phase 220
Three phase 230
Three phase 230
Three phase 380
Three phase 380
Three phase 400
Three phase 440
Three phase 440
60
60
50
60
50
60
50
60
50
60
50
60
50
50
60
0.9
2000 200 28 2600 260 37 1550 10 250
2.5 400
- -
- -
- -
2000 200 28
3000 300 42 1300
2600 260 37 1550
3000 300 42 1300
2600 260 37 1550
2600 260 37
2600 260 37
3000 300 42 1300
2600 260 37 1550
3000 300 42 1300
2600 260 37 1550
3000 300 42 1300
2600 260 37 1550
2600 260 37
3000 300 42 1300
3000 300 42 1300
2600 260 37 1550
0.45
0.4
0.22
0.18
Output
HP
W
VAC
Hz
r/min VAC
ל
A
mN.mgfcm oz-in mN.mgfcm oz-in
Voltage
Starting Torque
Rated Torque
Capacitor
Rated
Speed
Freq.
Current
40
Terminal Box Type
Model
9IDGŪ-40G : Pinion Shaft Type
9IDDŪ-40 : D-Cut Shaft Type
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
TP
60Hz
900 600 500 360 300 240 200 180 144 120 100 72 60 50 45 36 30 24 20 18
2 3 3.6 5 6 7.5 9 10 12.5 15 18 25 30 36 40 50 60 75 90 100
5.0 6.8 8.2 11.3 13.6 17.0 20.4 22.7 28.4 34.0 40.8 51.1 61.3 73.6 81.5 100 100 100 100 100
0.50 0.68 0.82 1.13 1.36 1.70 2.04 2.27 2.84 3.40 4.08 5.11 6.1 7.4 8.2 10 10 10 10 10
4.4 6.0 7.2 10.0 12.0 15.0 18.0 20.0 25.1 30.0 36.0 45.1 54.1 65.0 72.0 88 88 88 88 88
15 12 10
120 150 180
100 100 100
10 10 10
88 88 88
9GBK
Ū
MH
9IDG
Ū
-40G
speed RPM (r/min)
Gear Ratio
Model
Motor/Gearhead
kgf cm
N.m
lb-in
50Hz
750 500 417 300 250 200 167 150 120 100 83 60 50 42 38 30 25 20 17 15
2 3 3.6 5 6 7.5 9 10 12.5 15 18 25 30 36 40 50 60 75 90 100
6.0 8.3 9.9 13.8 16.5 20.7 24.8 27.5 34.4 41.3 49.6 62.1 74.5 89.4 99.1 100 100 100 100 100
0.60 0.83 0.99 1.38 1.65 2.07 2.48 2.75 3.44 4.13 4.96 6.21 7.5 8.9 9.9 10 10 10 10 10
5.3 7.3 8.7 12.2 14.6 18.3 21.9 24.3 30.4 36.5 43.8 54.8 65.8 78.9 87.5 88 88 88 88 88
13 10 8
120 150 180
100 100 100
10 10 10
88 88 88
9GBK
Ū
MH
9IDG
Ū
-40G
speed RPM (r/min)
Gear Ratio
Model
Motor/Gearhead
kgf cm
N.m
lb-in