Specifications

Ū
90mm(3.54in.)
SPEED CONTROL MOTOR
40W
ū Motor Specification
Lead Wire Type
9SDG(D)A-40G
9SDG(D)B-40G
9SDG(D)C-40G
9SDG(D)D-40G
9SDG(D)E-40G
9SDG(D)F-40G
9SDG(D)A-40G-T
9SDG(D)B-40G-T
9SDG(D)C-40G-T
9SDG(D)D-40G-T
9SDG(D)E-40G-T
9SDG(D)F-40G-T
1/18
Single Phase 110
Single Phase 115
Single Phase 220
Single Phase 220
Single Phase 230
Single Phase 230
60
60
50
60
50
60
90~1700
2600 260 26.4 700 70 9.8 1800 180 25.2 0.90 10 250
3000 300 42.0 630 63 8.8
2300 230 32.2 630 63 8.8
1400 140 19.6 0.45 2.5 400
3000 300 42.0 630 63 8.8
2300 230 32.2 630 63 8.8
90~1400
90~1700
90~1400
90~1700
Output
HP
W
gfcm mN.m oz-in
Permissible Torque
1200rpm 90rpm
Starting Torque
40
Terminal Box Type
Model
9SDGŪ-40G : Pinion Shaft Type
9SDDŪ-40 : D-Cut Shaft Type
gfcm mN.m oz-in
gfcm mN.m oz-in
TP
TP
TP
TP
TP
TP
ҊEnter the gear ratio in the box (Ū) within the gearhead model name. A colored background indicates gear shaft rotation in the same direction
as the motor shaft ; a white background indicates rotation in the opposite direction.
ҊThe speed is calculated by dividing the motorĹs synchronous speed (50Hz : 1500 r/min, 60 Hz : 1800 r/min) by the gear ratio.
ҊThe actual speed is 2~20% less than the displayed value, depending on the size of the load.
ҊIf more slow speed is needed than above value, use decimal gearhead with a gear ratio of 10:1 could be used between general gearhead and
motor. Even in this case, just speed will be reduced without increase in permissible torque; the maximum permissible torque is 100kgfcm
ū P
ermissible Torque When using gearhead
LEAD WIRE TYPE DSKDSA
SPEED CONTROL 40W
VAVAC Hz rpm
ל
Voltage
Condenser
Freq.
Current
Speed
Range
ҊEnter the ĸPhase & VoltageĹcode in the box(Ū) within the
motor model name.
ҊĸPinion ShaftĹis for attaching gearhead and ĸD-Cut ShaftĹis
for using motor only.
: Contains a built-in thermal protector. If a motor
overheats for any reason the thermal protector opened
and the motor stops. When the motor temperature
Drops, the thermal protector closes and the motor
restarts. Be sure to turn the motor off before inspecting.
By attaching F2 FAN additionally, temperature reducing
of over 10œ could be available.
TP
2 3 3.6 5 6 7.5 9 10 12.5 15 18 25 30 36 40 50 60 75 90 100
5.5 6.3 7.6 11 13 16 19 23 26 32 38 47 57 68 72 86 100 100 100 100
0.55 0.63 0.76 1.10 1.3 1.6 1.9 2.3 2.6 3.2 3.8 4.87 5.7 6.8 7.2 8.6 10 10 10 10
4.9 5.6 6.7 9.7 11.5 14.1 16.8 20.3 23 28 34 42 50 60 64 76 88 88 88 88
4.5 5.6 6.7 9.3 11 14 17 19 23 28 34 42 50 60 68 76 91 100 100 100
0.45 0.56 0.67 0.93 1.1 1.4 1.7 1.9 2.3 2.8 3.4 4.2 5.0 6.0 6.8 7.6 9.1 10 10 10
4.0 4.9 5.9 8.2 9.7 12.4 15 17 20 25 30 37 44 53 60 67 80 88 88 88
6.5 7.3 8.7 12 15 18 22 25 30 36 44 55 66 79 85 99 100 100 100 100
0.65 0.73 0.87 1.20 1.5 1.8 2.2 2.5 3.0 3.6 4.4 5.5 6.6 7.9 8.5 9.9 10 10 10 10
5.7 6.4 7.7 10.6 13.2 15.9 19 22 26 32 39 49 58 70 75 87 88 88 88 88
1.5 1.7 2.0 2.8 3.4 4.3 5.1 6.1 7.1 8.5 10 13 15 18 20 23 28 35 42 46
0.15 0.17 0.20 0.28 0.34 0.43 0.51 0.61 0.71 0.85 1.0 1.3 1.5 1.8 2.0 2.3 2.8 3.5 4.2 4.6
1.3 1.5 1.8 2.5 3.0 3.8 4.5 5.4 6.3 7.5 8.8 11.5 13.2 15.9 17.7 30 25 31 37 41
1.3 1.5 1.8 2.6 3.1 3.8 4.6 5.5 6.4 7.7 9.2 11 14 17 19 21 25 30 37 42
0.13 0.15 0.18 0.26 0.31 0.38 0.46 0.55 0.64 0.77 0.92 1.1 1.4 1.7 1.9 2.1 2.5 3.1 3.7 4.2
1.15 1.32 1.59 2.3 2.7 3.4 4.1 4.9 5.7 6.8 8.1 10 12 15 17 19 22 27 33 37
rpm
1200
90
Voltage Gear Ratio
110/115
60Hz
220/230
60Hz
220/230
50Hz
110/115
60Hz
220/230
Motor/Gearhead
kgf cm
N.m
lb-in
kgf cm
N.m
lb-in
kgf cm
N.m
lb-in
kgf cm
N.m
lb-in
kgf cm
N.m
lb-in
9SDGŪ-40G /
9GBKŪMH
120 150 180
100 100 100
10 10 10
88 88 88
100 100 100
10 10 10
88 88 88
100 100 100
10 10 10
88 88 88
55 69 83
5.5 6.9 8.3
49 61 73
50 62 75
5.0 6.2 7.5
44 55 66