Specifications

Ū
90mm(3.54in.)
200W
ū Motor Specification - 30min. Rating (Continuous : F2 fan)
ū Permissible Torque When using gearhead
LEAD WIRE TYPE MOTOR LEAD WIRE TYPE MOTOR TERMINAL BOX TYPE MOTOR LEAD WIRE TYPE MOTOR
ELECTROMAGNETIC BRAKE MOTOR
(Power off activated type)
ҊEnter the ĸPhase & VoltageĹcode in the box(Ū) within the motor model name.
ҊĸPinion ShaftĹis for attaching gearhead and ĸD-Cut ShaftĹis for using motor only.
: Contains a built-in thermal protector. If a motor overheats for any reason the thermal protector opened and the motor stops. When the
motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor off before inspecting. By
attaching F2 FAN additionally, temperature reducing of over 10œ could be available.
TP
ҊEnter the gear ratio in the box (Ū) within the gearhead model name. A colored background indicates gear shaft rotation in the same direction
as the motor shaft ; a white background indicates rotation in the opposite direction.
ҊThe speed is calculated by dividing the motorĹs synchronous speed (50Hz : 1500 r/min, 60 Hz : 1800 r/min) by the gear ratio.
ҊThe actual speed is 2~20% less than the displayed value, depending on the size of the load.
ҊIf more slow speed is needed than above value, use decimal gearhead with a gear ratio of 10:1 could be used between general gearhead and
motor. Even in this case, just speed will be reduced without increase in permissible torque; the maximum permissible torque is 200kgfcm (P
type) / 300kgfcm (H type).
TP
TP
TP
TP
TP
TP
TP
TP
TP
Lead Wire Type
9BDG(D)G-200P(H)
9BDG(D)H-200P(H)
9BDG(D)I-200P(H)
9BDG(D)J-200P(H)
9BDG(D)K-200P(H)
9BDG(D)L-200P(H)
9BDG(D)M-200P(H)
9BDG(D)N-200P(H)
9BDG(D)O-200P(H)
9BDG(D)G-200P(H)-T
9BDG(D)H-200P(H)-T
9BDG(D)I-200P(H)-T
9BDG(D)J-200P(H)-T
9BDG(D)K-200P(H)-T
9BDG(D)L-200P(H)-T
9BDG(D)M-200P(H)-T
9BDG(D)N-200P(H)-T
9BDG(D)O-200P(H)-T
1/4
30min
30min
30min
Three phase 220
Three phase 220
Three phase 230
Three phase 230
Three phase 380
Three phase 380
Three phase 400
Three phase 440
Three phase 440
50
60
50
60
50
60
50
50
60
0.90
0.68
14500 1450 205
14500 1450 205
14500 1450 205
15000 1500 212 1300
12500 1250 177 1550
15000 1500 212 1300
12500 1250 177 1550
15000 1500 212 1300
12500 1250 177 1550
15000 1500 212 1300
15000 1500 212 1300
12500 1250 177 1550
1.80
Output
Starting
Time
HP
W
VAC
Hz
r/min VAC
ל
A
mN.mgfcm oz-in mN.mgfcm oz-in
Voltage
Starting Torque
Rated Torque
Capacitor
Rated
Speed
Freq.
Current
200
Terminal Box Type
Model
9BDGŪ-200P(H) : Pinion Shaft Type
9BDDŪ-200 : D-Cut Shaft Type
- -
- -
- -
60Hz
900 600 500 360 300 240 200 144 120 100 90 72 60 50 45 36 30 24 20 18
2 3 3.6 5 6 7.5 9 12.5 15 18 20 25 30 36 40 50 60 75 90 100
28 30 36 51 61 76 91 114 137 164 200 200 200 200 200 200 200 200 200 200
2.8 3 4 5 6 8 9 11 14 16 20 20 20 20 20 20 20 20 20 20
25 27 32 45 54 67 81 101 121 145 177 177 177 177 177 177 177 177 177 177
- 32 38.3 - 64 - 96 120 144 173 - 216 259 300 - 300 300 300 300 300
- 3 4 - 6 - 10 12 14 17 - 22 26 30 - 30 30 30 30 30
- 28 34 - 57 - 85 106 127 153 - 191 229 265 - 265 265 265 265 265
15 12 10
120 150 180
200 200 200
20 20 20
177 177 177
300 300 300
30 30 30
265 265 265
9PBKŪBH
9PFKŪBH
9HBKŪBH
9BDGŪ-200FP
9BDGŪ-200FH
speed RPM (r/min)
Gear Ratio
Model
Motor/Gearhead
kgf cm
N.m
lb-in
kgf cm
N.m
lb-in
50Hz
750 500 417 300 250 200 167 120 100 83 75 60 50 42 38 30 25 20 17 15
2 3 3.6 5 6 7.5 9 12.5 15 18 20 25 30 36 40 50 60 75 90 100
33 37 45 62 74 92 111 139 166 200 200 200 200 200 200 200 200 200 200 200
3.3 4 4 6 7 9 11 14 17 20 20 20 20 20 20 20 20 20 20 20
29 33 39 54 65 82 98 122 147 176 177 177 177 177 177 177 177 177 177 177
- 39 47 - 78 - 117 146 175 210 - 262 300 300 - 300 300 300 300 300
- 4 5 - 8 - 12 15 18 21 - 26 30 30 - 30 30 30 30 30
- 34 42 - 69 - 103 129 155 185 - 231 265 265 - 265 265 265 265 265
13 10 8
120 150 180
200 200 200
20 20 20
177 177 177
300 300 300
30 30 30
265 265 265
9PBKŪBH
9PFKŪBH
9HBKŪBH
9BDGŪ-200FP
9BDGŪ-200FH
speed RPM (r/min)
Gear Ratio
Model
Motor/Gearhead
kgf cm
N.m
lb-in
kgf cm
N.m
lb-in