Installation Sheet
4
Assembly Instructions for Modular
application (linked to a CAD cart):
Note: Installation of optional drain pump (sold
separately - model # RF15I-P) must be done
before installation of wrapper.
Remove (2) screws on front bottom grill cover from 1.
the Icemaker and set them aside (Fig. 01).
Remove (4) screws on back panel of Icemaker as 2.
shown (Fig. 02). (Retain screws for re-use.)
Install 2 Tinnerman U-Nuts on Icemaker Adapter (Fig. 3.
03) and attach to upper area of Icemaker as shown
(Fig. 04 and 05). Repeat for the bottom location.
Tighten all screws at this point.
With the grill head out of the cart, place the 4.
corresponding wrapper side panel against cart
side. Align the holes at the top front and rear side
corners and install hex bolts (1/4-20 X 1/2 HEX BLT)
and locking nuts (1/4-20 HEX NUT) provided with
hardware kit, using the second hole from the top on
the cart panel and top hole on the wrapper panel
(Fig. 15). Do not tighten at this point.
Before connecting the two units, make sure that all 5.
of the height requirements are matched:
The Icemaker leveling legs can be adjusted a.
to match the cart assembly or your counter top.
Check the level on both units. The bottom front
corners will match and the front faces will be
ush (Fig. 16).
When installing multiple units as a permanent b.
installation (such as an island) it is recommended
to remove the cart casters and install leveling
legs (sold separately - model # CAD-LVL).
Align the bottom front ange with the Icemaker (Fig. 3.
06 ). Slide the units together so the U-nut holes are
visible in the slotted holes of the upper and lower
rear anges of the side panel. Install machine screws
(10-24 X 3/8) into U-nuts as shown (Fig. 07 and 08).
Do not tighten at this point. Take care not to damage
anges on the female clips.
Level the legs on the Icemaker as described in 5a. 4.
Reinstall bottom front grill cover and screws. Leave
screws loose about 1/8 of an inch.
Note: If connecting Icemaker between carts,
repeat steps (4-6) for opposite side of
Icemaker, then proceed to step 9.
Place the other side panel on the unit by 5.
aligning bottom front ange with the Icemaker
(Fig. 06). Lift the rear of the side so the U-nut holes
are visible in the slotted holes of the upper and lower
rear anges of the side panel. Install machine screws
(10-24 X 3/8) into U-nuts as shown (Fig. 07 and 08).
Do not tighten at this point. Take care not to damage
anges on the female clips.
Place both top risers on top of unit as shown in 6.
(Fig. 09).
Using the machine screws provided (10-24 X 1-1/8) 7.
attach risers to side panels. Take note of alignment of
the holes on the riser and side panels (Fig. 10).
Make a nal adjustment to the Icemaker leveling 8.
legs so the side panels are level with the top unit,
and then tighten all screws, front and rear.
The 4 male catch clips are preinstalled in the back 9.
panel. See your Icemaker Use & Care Manual for
instructions on connecting to your potable water
supply and drain. Route the supply hose thru the
large opening in the back panel and connect to
the inlet on the back of the Icemaker. If you have
installed the optional drain pump (sold separately -
model # RF15I-P), feed the drain line thru this same
large opening. Feed the power cord thru the smaller
opening and install protective grommets on all
openings (Fig. 11).
Once you have tested the unit and veried there 10.
are no leaks, align the rear panel male clips to the
preinstalled female clips of the side panels, push at
the outer corners to engage clips. See Fig. 14 for nal
assembly. Do not bundle-up excess hose & cord
behind the panel.
See Solid Surface Installation (page 3).11.
The grill head(s) can now be installed in the grill cart, 12.
refer to instructions in Grill or Cart Manual.
Fig. 15
SIDE PANEL
CAD CART
REAR VIEW
Front Lower
Flange
Front Faces
Flush
Bottom front
corners
CAD CART
ICE MAKER
Fig. 16