Installation Sheet

ManualsBrandsDCS Appliances ManualsOutdoor Kitchen ComponentsDCS Appliances Insulated Jacket for Liberty Ice Maker

WRAPPER FOR FREE STANDING ICEMAKER

INSTALLATION INSTRUCTIONS

Before you begin, read these instructions completely and carefully.

Getting Started

Remove packaging and retain until installation is complete.

CAUTION:

The surface on which the grill cart and Icemaker are located must be at and level. Icemaker should be

installed near water and drain supply. All plumbing must be out of the way of any foot trac.

Note: Wrapper must be installed on the Icemaker and attached to the grill cart before the grill head is

installed on the cart.

WARNING!

Some parts have sharp edges; care must be taken when handling the various components to avoid injury.

Please read safety information provided in these instructions before beginning assembly. Wear gloves

when handling.

Tools Required

Phillips Screwdriver

5/16 Socket/Nutdriver and 5/16 Wrench

Safety Glasses

Work Gloves

Contents

Part Description Qty

Hardware Kit Includes:

Protective Grommet, 2.50 Diameter

Protective Grommet, 1.25 Diameter

Machine Screw 10-24 X 1-1/8

Sheet Metal Screw 10-24 X 1/2

Hex Bolt 1/4-20 X 1/2

Nut, Hex 1/4-20

Nut, Tinnerman U-nut #10-24 MS

Machine Screw 10-24 X 3/8

7” Cable Tie

Installation Instructions

Assembly instructions for Freestanding

application:

Note: Installation of optional drain pump (sold

separately - model # RF15I-P) must be done

before installation of wrapper.

Fig. 01

Front bottom grill cover

Screws

Loosen (2) screws on front bottom grill cover 1.

(Fig. 01) approx. 1/8”. (No need to remove screws.)

Summary of content (8 pages)

PAGE 1
WRAPPER FOR FREE STANDING ICEMAKER installation instructions Before you begin, read these instructions completely and carefully. Getting Started Remove packaging and retain until installation is complete. CAUTION: The surface on which the grill cart and Icemaker are located must be flat and level. Icemaker should be installed near water and drain supply. All plumbing must be out of the way of any foot traffic.
PAGE 2
. Remove (4) screws on back panel of Icemaker as shown (Fig. 02). (Retain screws for re-use.) 4. Place the left side panel on the unit by sliding the bottom front flange behind the front grill plate (Fig. 07). Then lift the rear of the panel so the U-nut holes are visible in the slotted holes of the upper and lower rear flanges of the panel. Install machine screws (10-24 X 3/8) into U-nuts as shown (Fig. 08 and 09). Do not tighten at this point.
PAGE 3
7. Using screws provided (10-24 X 1-1/8), attach riser to the side panels. Take note of the alignment of the holes on the riser and side panel (Fig. 11). 10. Once you have tested the unit and verified there are no leaks, align the rear panel male clips to the preinstalled female clips of the side panels, push at the outer corners to engage clips. See Fig. 13 for final assembly. Do not bundle-up excess hose & cord behind the panel. Ensure holes are aligned Fig. 11 Fig. 13 8.
PAGE 4
Assembly Instructions for Modular application (linked to a CAD cart): b. When installing multiple units as a permanent installation (such as an island) it is recommended to remove the cart casters and install leveling legs (sold separately - model # CAD-LVL). Note: Installation of optional drain pump (sold separately - model # RF15I-P) must be done before installation of wrapper. 3. Align the bottom front flange with the Icemaker (Fig. 06 ).
PAGE 5
For optional type and colors of the Solid Surface, contact your local manufacturer and provide drawing in Fig. 17. 2X .18 BOTH SIDES 2X 2X Ø.250 BOTH SIDES DETAIL C SCALE 1 : 2 C Ø .50 X .150 DEEP BOTH SIDES 17-7/32" R 1/4" ALL TOP AND 4 X CORNERS REAR OF UNIT 1/2" ALL WALLS 25-1/2"* 21.652 * 2.894 * 1.300 * FRONT OF UNIT 16.213 * NO EPOXY BUILD UP ALL INSIDE CORNERS Fig.
PAGE 6
NOTES 6
PAGE 7
NOTES 7
PAGE 8
Fisher & Paykel Appliances, Inc. 5900 Skylab Road, Huntington Beach, CA 92647 Customer Care: 888.281.5698 • Fax: 714.372.7003 www.dcsappliances.