User Guide

Modeling
- Gain - 0 to 99
This parameter controls the input gain of the signal flowing into the microphone preamp model.
Values are from 0-99.
Modeling - Low-Cut Freq - 0 to 50
This parameter controls the low-cut frequency. All audio below this frequency will be removed.
Values are from 0-50.
EQ - Low Gain - -12 to 12 (+/-12dB @ 80Hz)
This parameter controls the Low-gain output of the EQ section and ranges from -12 to +12dBu.
EQ - Mid Frequency - 0 to 61 (400Hz to 8kHz)
This parameter is used to select the mid EQ frequency. Values are as follows: 1). 400.Hz 2).
420.48Hz 3). 442.01Hz 4). 464.63Hz 5). 488.42Hz 6). 513.43Hz 7). 539.71Hz 8). 567.34Hz 9). 596.39Hz 10). 626.92Hz
11). 659.02Hz 12). 692.76Hz 13). 728.23Hz 14). 765.51Hz 15). 804.70Hz 16). 845.90Hz 17). 889.20Hz 18). 934.73Hz
19). 982.58Hz 20). 1032.89kHz 21). 1085.77kHz 22). 1141.35kHz 23). 1199.79kHz 24). 1261.21kHz 25). 1325.78kHz
26). 1393.66kHz 27). 1465.01kHz 28). 1540.01kHz 29). 1618.85kHz 30). 1701.73kHz 31). 1788.85kHz 32). 1880.44kHz
33). 1976.71kHz 34). 2077.91kHz 35). 2184.29kHz 36). 2296.12kHz 37). 2413.67kHz 38). 2537.24kHz 39). 2667.14kHz
40). 2803.69kHz 41). 2947.23kHz 42). 3098.11kHz 43). 3256.72kHz 44). 3423.46kHz 45). 3598.72kHz 46). 3782.97kHz
47). 3976.64kHz 48). 4180.23kHz 49). 4394.24kHz 50). 4619.21kHz 51). 4855.70kHz 52). 5104.29kHz 53). 5365.61kHz
54). 5640.31kHz 55). 5929.08kHz 56). 6232.62kHz 57). 6551.71kHz 58). 6887.13kHz 59). 7239.73kHz 60). 7610.38kHz
61). 8000kHz
EQ - Mid Q - 0 to 10 (.25-16)
This parameter is used to select the mid Q curve of the EQ. Selections are from 0 to 10, giv-
ing Qs of: .25, .5, .75, 1.0, 1.25, 2.0, 4.0, 8.0 and 16.0.
EQ - Mid Gain - -12 to 12
This parameter controls the Mid-gain output of the EQ section and ranges from -12 to +12dBu.
EQ - High Gain - -12 to 12 (+/-12dB @ 12kHz)
This parameter controls the High-gain output of the EQ section and ranges from -12 to +12dBu.
Compressor
- Threshold - 1 to 60
Adjust this knob to set the threshold of compression from -40dBu (7.8mVrms) to +20dBu. Setting
the Compressor THRESHOLD at its highest level will prevent all but the highest level peaks from
being compressed. Setting the Compressor RATIO to 1:1 will turn the Compressor off, regard-
less of the setting of the Compressor THRESHOLD control.
Compressor - Ratio - 0 to 50 (1:1 - Inf:1)
Rotate this control clockwise to increase the amount of compression from 1:1 (no compres-
sion) up to ∞:1 (no increase in output level, regardless of input level increases above thresh-
old.)
Compressor - Gain - 0 to 20 (0-20dB)
This control is used to adjust the output gain of the Compressor module in 1dB increments.
Compressor - Attack - 1 to 99 (1-200ms)
The ATTACK control sets the amount of time it takes the ProVoca™l to begin compressing a sig-
nal (once the detector has sensed a signal above threshold). The ATTACK range is from 1 (FAST)
for a tighter and more noticeable compression effect with very little overshoot) to 99 (SLOW)
Detailed Parameters
Section 2
ProVocal
™
ProVocal™ User Manual
7