User Manual VoIP FXS+PSTN Gateway Model: HT-822P For DC24V Only Shenzhen HyberTone Technology Co.,Ltd. Http://www.hybertone.com Support@hybertone.com Marketing@hybertone.com Date: 2007-9-17 Version: A38HS-3.
HT-822P VoIP FXS+PSTN Gateway Http://www.hybertone.com Contents 1 Product Introduction.......................................................................4 1.1 General Information............................................................................................................4 1.2 Protocol...............................................................................................................................4 1.3 Hardware Specification...................................................
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway 4.3.7 Default Connect ..................................................................................................20 4.4 Call Settings ......................................................................................................................20 4.4.1 H.323 Phone .......................................................................................................21 4.4.1.1 Single Configuration ........................................
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway 6 Manufactory Parameter ................................................................
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway 1 Product Introduction 1.1 General Information An Analogue Telephone Adaptor (ATA) is an analogue-to-digital adaptor that allows you to use your standard telephone or telephone system. ATA is designed to realize voice communication over a broadband IP network. It offers high voice quality with minimal bandwidth requirement.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway 1.3 Hardware Specification ARM9E Processor for high performance DSP for voice codec and voice processing Two 100M Based Ethernet ports in comply with IEEE 802.3 for both LAN and PC connection. LEDs for Ethernet port status Two FXS ports One PSTN port Ethernet Bridge 1.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway 1.6 View of the Appearance 1） Phone 1 It is connected with a standard touch-tone analog telephone. 2） Phone 2 It is connected with another standard touch-tone telephone. 3） LINE IN It is connected with a standard telephone cable PSTN or VoIP. 4） LAN It is used to connect the Ethernet cable. 5） PC It is used to connect a computer or other terminal. 6） POWER DC24V/500mA It is the power port, connected with the power adaptor.
Http://www.hybertone.com a) b) c) d) e) HT-822P VoIP FXS+PSTN Gateway Connect a standard touch-tone analog telephone to the PHONE port. Insert a standard RJ11 telephone cable into the LINE IN port and connect the other end of the telephone cable to a wall jack. Insert the Ethernet cable into the LAN port of HT-822P IP ADAPTOR and connect the other end of the Ethernet cable to an uplink port (a router or a modem, etc.) Connect a PC to the PC port of HT-822P IP ADAPTOR.
HT-822P VoIP FXS+PSTN Gateway Http://www.hybertone.com kind of star command is shown in the table below. Star(*) Command Function *01 Read LAN Port IP *02 Read PC Port IP *03 Set LAN Port IP. Pick up the handset, press *03, and then follow the instruction of the phone to set the IP address. *04 Set PC Port IP. Pick up the handset, press *04, and then follow the instruction of the phone to set the IP address. *20 Send a remote support request. *09987456 Reset IP: LAN Port IP: 192.168.0.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway or Phone 2 port. Please refer to the table in section 3.1.1 for detailed information. While seting up, please follow the instructions as follows : a) b) c) d) e) When the HT-822P IP ADAPTOR fails to set the LAN Port and PC Port IP addresses, it reports 0 on *01 or *02 Star Commands. When the PC port is configured into Bridge Mode, it also report zero. *03 and *04 can be dialed to set the LAN Port IP address and PC Port IP address.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway extension. To temporarily put the present caller on hold and answer the new incoming call, press *42 and you will hold the current call. And press *42 again, you will return to the former call. Note: This function only support by SIP protocol. 3.3.1.3 Call-transfer If A and B are in the process of a call, A can transfer A-B call to B-C call. There are two kinds of transfer, which are attended transfer and unattended transfer.
HT-822P VoIP FXS+PSTN Gateway Http://www.hybertone.com b) your own PSTN Access Code) at first. Wait for the PSTN dial tone and dial the PSTN number. If the default connect of FXS MODE in the configuration web is PSTN, dial the phone number directly. 3.3.4 Send and Receive VoIP Calls Users can send and receive calls from the VoIP. A. To receive VoIP calls, just take the phone off hook when it rings. B. To make a VoIP call: a) If the default connects is VoIP, dial the number directly.
HT-822P VoIP FXS+PSTN Gateway Http://www.hybertone.com 2. PC 1. 2. L1 1. 2. L2 1. 2. up continuously. ( The LED will not light up if the network connection is unavailable ) If there is data transmitting through the ATA, the LAN LED will blink. (Example: During a VoIP call, the LED will keep blinking.) When the PC receptacle is connecting with the network, the PC LED will light up continuously. (The LED will not light up if the network connection is unavailable.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway 4 Configuration Guide Before configuring the HT-822P IP ADAPTOR, first you should obtain the LAN or PC IP address through voice prompt. Follow section 3.1 for detailed information to get the LAN or PC IP Address. HT-822P IP ADAPTOR has an embedded Web server that will respond to HTTP GET/POST requests. It also has embedded HTML pages that allow users to configure the HT-822P IP ADAPTOR through a Web browser. 4.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway To login the Administration Configuration page, please enter “admin” in the User Name field and “admin” (default) in the Password field and then click on the OK button. The PC Browser then shows the window below and you have successfully entered the HT-822P IP ADAPTOR HTTP WEB Interface.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway 4.2 Status As shown in the figure above, there are four main fields to be configured on the Status page. 4.2.1 Phone Information A. Serial Number Each ATA has a unique serial number assigned by the factory such as HT822POLDTEST09. This number is important for centralized configuration, technical support, and warranty repair. This number is printed in the back of the ATA and is associated with your software license. This field is read-only. B.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway most zones have two or more authoritative servers.) A name server retains the address and routing information for IP users. 4.3 Configurations Options Click on the “Configurations”, the web page will pop-up a subordinate options. Click on “Preference” in the left menu of the configuration web, and the screen will be displayed as follows: 4.3.1 Language Select web provisioning language as English or Chinese.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway 4.3.2 Time Zone and Time Server This parameter controls how the date/time displayed, it will be adjusted according to the specified time zone. The ATA uses Network Time Protocol (NTP) to retrieve date and time information from an NTP server (Time Server). The time is in GMT ± offset. For example, Pacific Standard Time is GMT-8, and Pacific Daylight Time is GMT-7.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway The Remote Control star command is *20, this star command’s rule is: *20 + Server IP + Server Port + # For examples, if you want send a support request to the engineer and your SIP’s Remote Control Server’s IP is 222.111.222.111, the Remote Server Port is 1920. You can dial the command like this: *20222*111*222*111*1920#. If you set this IP and Port on you device’s Web, you only dial *20#. 4.3.
Http://www.hybertone.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway 4.3.7 Default Connect There are two kinds of default connect: VoIP and PSTN. You can switch between the two connects. a) Short for Voice over IP, VoIP is a category of hardware and software that enables people to use the Internet as the transmission medium for telephone calls by sending voice data in packets using IP. Select this field to set your default connects into VoIP. If you make a VoIP call, please dial the called number directly.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway 4.4.1 H.323 Phone H.323 is the international standard for multimedia communication over packet-switched networks, including LANs, and the Internet. There are three kinds of FXS mode to configure: 1） Single Configuration; 2） Configuration by line ; 3）Configuration by Group . 4.4.1.1 Single Configuration In this configuration mode, you can give the two phones connected to the ATA the same configurations in the following items. A. H.323 Phone Number H.
Http://www.hybertone.com F. HT-822P VoIP FXS+PSTN Gateway Enable Auth If you click the “Enable Authentication” field, you will have to configure the Auth ID and Password. A pair of authentication ID and password is usually needed to use the ATA. 4.4.1.2 Configuration by Line In this mode, you will have more advance control over the two FXS ports. Firstly, phone 1 and phone 2 will refer to different service providers for related service.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway 4.4.1.4 Advance Settings Click on “Advance Settings” in the H.323 menu, the configuration screen of advance settings will be displayed as follows. In this part, you will have more advance control over the H.323 signaling. A） RAS Port RAS Port is connected to an unreliable channel, which is used to convey the registration, admissions, bandwidth change, and status messages between two H.323 entities. B） Q.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway Call Signaling Port is connected to a reliable channel used to convey the call setup and teardown messages between two H.323 endpoints. C） H.245 Port （ Media Control Ports ） Media control port is the port or port range used by the H.245 media control protocol. Note: the H.245 media control protocol uses TCP. D） Fast Start Enable or disable the Fast Start procedure described in H.225.0.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway DTMF Payload Type is used to carry telephony tones and telephony signals. By using a distinct dynamic RTP payload type in the same RTP stream as the media, it is possible to carry DTMF tones, fax-related tones, standard subscriber line tones, country-specific tones and trunk events. G） Signaling Qos 4.4.1.5 H.323 Direct Mode This is the Point to Point mode. 4.4.2 SIP Phone SIP (Session Initiation Protocol) is a relatively new Internet standard.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway 4.4.2.1 Single Configuration In this FXS mode, you can give the two phones connected to the ATA the same configurations in the following items. A）Phone Number This field use fill in the SIP client authentication ID. It is the telephone number (or extension) you assigned to the VoIP SIP Phone such as 123456. enter the phone number in the Phone Number field.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway can config it with SIP registrar server address field such as 192.168.2.197:2000 or gk.your.com:2000 (the 2000 is your SIP registrar server signaling port). D）Home Domain This field use fill in the IP address of the home domain. Although the IP address is easy to remember, the user still finds it hard to remember because it is long and has no association with its geographical position or organizational relationship.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway This is the spare VoIP system information, it offer a choice when the current system has some problem. 4.4.2.2 Configuration by Line In this mode, you will have more advance control over the two FXS ports. Firstly, phone 1 and phone 2 will refer to different service providers for related service. Secondly, you can bind the phone numbers or the FXS ports with each phone. That is to say, one phone terminal can be bound with two phone numbers.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway A） Signaling Port (SIP Local port) SIP local port is the local UDP port; the SIP proxy could have a conversation with SIP proxy server or other SIP user. B） Outbound Proxy This field shows the SIP outbound proxy IP address. In most cases, the SIP outbound proxy is placed alongside the firewall and is the way to let SIP traffic pass from the internal network to the Internet. Please ask your network administrator for these parameters.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway F） DTMF Signaling 1） DTMF TYPE DTMF TYPE is used for telephone signaling over the line in the voice frequency band to the call switching center. DTMF means that two groups of tone with different frequencies are united into 16 kinds of dial tone. The telecommunication station, switch or the phone service such as 1860 identify these special tones through DSP analysis to confirm the keys dialed by user.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway A） RTP Ports RTP (Real Time Protocol) Port is the target transport address for the RTP audio stream to be sent to. B） Packet Length it means the time of single network packet sent out . The default time is 20ms. C） Jitter Buffer D） Media Qos RTP TOS is a service field in UDP IP packets carrying a RTP data. Enter RTP TOS if your network supports DiffServ and can prioritize the packets to maintain voice quality. 4.4.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway the “Call Settings à Media Setting” configuration page, the “Codec Preference” screen will be displayed as below. Codec preference is the order of voice codec. The default one is up transmitting, which is the set mode for common users. 4.4.5 NAT Traversal 4.4.5.1 Signaling NAT Traversal Click on the “Signaling NAT Traversal” in the “Call Settings” configuration page’s “Advance Settings”, the “NAT Traversal” screen will be displayed as follows.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway phone to detect the presence and type of NAT behind which the phone is placed. SIP Stun Server refers the SIP address of the Stun Server. D） Nat Citron It only use by H.323 protocol. E） Relay Proxy Relay proxy is HyberTone's proprietary NAT traversal technology which enables HyberTone's VoIP terminals to achieve successful deployment in most LAN environments. It includes address, ports, user name, and password.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway The RELAY can run in three modes: Mode 1: The media use UDP packets and encrypt; Mode 2: The media use UDP packets and encrypt; The UDP packets use single UDP port; Mode 3: The media use TCP packets and encrypt; The TCP packets can choice single TCP port; The mode 2 and mode 3 is the passiveness, the port was designation from RELAY SERVER. Note: This RELAY Proxy is only compatible with the RELAY Server software developed by HyberTone independently.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway 4.4.7.1 Basic Dial Rule 1. If there are many rules, it can be separated with symbol '|'. For example: "00:-00|0:-0+86|:+86755" 2. System try to match the rule from left to right and stop match when meet the satisfied rule, otherwise continue. 3. Rule grammar model is "AA:-aa+bb", For example: "0:-0+86". In front of ":","AA" is the number to match, and what is operated is realized by the following.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway code and it's exact length. Configuration: If you set the rule of above example of 3 as follow: Before: "00:|0:-0+0086|:+0086755". Now: "00:|0:-0+0086|[1-8]xxxxxxx:+0086755". Now, the length of local telephone number is limited in 8 bit ,first bit is range from 1 to 8. Then the gateway will add 0086755 in front of telephone number and dial out.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway 4.5.1 Start VoIP dial The default number is *12. If the line is default PSTN, press *12 and you will switch to VoIP line. 4.5.2 Switch to PSTN The default number is *21. If the line default is VoIP, press *21 and you will switch to PSTN line. 4.5.3 Hold Key The default number is *42. If you are in the process of a call, press *42 and you will put the call on hold. 4.5.4 Transfer Key The default number is *41.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway Note: The range of the Input Gain can induce the terminal can not dial the phone number. If you meet this phenomenon and you adjusted it, Please resume or lessen the range of the Input Gain. 4.7 PhoneBook The HT-822P can storage 20 phone number. Click on the PhoneBook in the left menu the screen will display as below.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway User can edit the phonebook and dial up the phone number using the phone book function. 4.8 About FAX HyberTone Technology Co.,Ltd. Declare the HT-822P nonsupport FAX function. But it was build-in two type free FAX codes. Note: HyberTone Technology Co.,Ltd. Declare the HT-822P Gateway are nonsupport FAX function. HyberTone Technology Co.,Ltd. don’t supply any FAX support for HT-822P Gateway. 4.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway The Network Configurations screen allows you to set up the IP addresses of the LAN and PC port, Bridge or Router mode (by selecting or deselecting Bridge Mode), default Gateway Address, and Primary and Secondary DNS server IP addresses. It includes LAN port configurations and PC port configurations. 4.8.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway In a typical geographically determined network, users input telephone numbers manually. If you obtain a static IP address from your ISP, you can assign it to the ATA LAN port by clicking the Static IP Address Manually, and then entering the IP Address, Subnet Mask, and Default Route. 3） PPPoE PPPoE, point-to-point protocol over Ethernet, is a network protocol for encapsulating PPP frames in Ethernet frames.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway 1） Bridge Mode In the Bridge Mode, the ATA allows a PC connected to it to pass through to the network. No other PC Configuration settings are set; the Advanced Settings, Gateway, Primary and Secondary DNS field settings are not required and will be ignored. 2） Specify an IP Address Manually Click Static IP, and enter IP Address and Subnet Mask.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway Hardware Address is an address used to enter the MAC address in XX: XX: XX: XX: XX: XX format. Broadcast Address is an address used to communicate with the other computers connected to the PC side of the ATA. 4.8.3 Primary DNS DNS is the abbreviation for domain name server, domain name system.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway 4.10 Discard Changes 4.11 Tools Menu Click on the “Tools”, the web page will pop-up a subordinate options and the screen will be displayed as follows: 4.11.1 Online Upgrade WARNING! Performing an online upgrade is for experienced users or administrators only! Click Online Upgrade. Enter the IP address or domain name of the upgrade server and package name: http://202.96.136.145/update/A34HS-3.07-18.pkg， And then click Start.
Http://www.hybertone.com HT-822P VoIP FXS+PSTN Gateway WARNING! When the terminal was updating , please don’t cut the power. It will destroy the terminal. 4.11.2 Change Password A） User Password The ATA supports multiple levels of user administration. The user password is set to allow you to configure the phonebook and other user administrative tasks. The default is 1234. You can change it according to your own wish.
HT-822P VoIP FXS+PSTN Gateway Http://www.hybertone.com 4.11.4 Reboot the Device Click on this field to reboot the device.
HT-822P VoIP FXS+PSTN Gateway Http://www.hybertone.com 6 Manufactory Parameter Parameter Network Password Default LAN DHCP PC Fixed IP : 192.168.8.1 admin user Time Zone dbl#admin or admin 1234 GMT＋8 The default star command please refer to the table in section 3.1.1 for detailed information. This default parameter are unsuitability the customization’s products.
