User Manual FXO+FXS Gateway Model: HTM Series DBL Technology Co.,Ltd. Http://www.dbltek.com/en sales@dbltek.com Support@dbltek.
http://www.DBL.com FXS+FXO Gateway Series Contents 1. Product Introduction.......................................................... 4 1.1 General Information ............................................................................................................4 1.2 Protocol ...............................................................................................................................4 1.3 Hardware Specification.........................................................................
http://www.DBL.com FXS+FXO Gateway Series 4. Tools....................................................................................................................................41 4.1. Online Upgrade ................................................................................................................41 4.2. Change Password .............................................................................................................42 4.3. Restore factory settings ...........................
http://www.DBL.com FXS+FXO Gateway Series 1. Product Introduction 1.1 General Information HTM series VoIP gateways are the performance Gateway of FXO plus FXS, which developed by Technology Co., Ltd. HTM Series VoIP gateways built-in H.323 and SIP protocols. The lines can be configured into different numbers or used for Trunk Gateway. Highly reliable line detection prevents the line hanging death in the largest tent.
http://www.DBL.com FXS+FXO Gateway Series 1.3 Hardware Specification ¾ ¾ ¾ ¾ ¾ ¾ ARM9E Processor DSP for voice codec and voice processing Two 10/100 Base T Ethernet ports with full compliant with IEEE 802.3 LEDS for Ethernet port status Direct Connect Ethernet cable Four PSTN Channels’ Connection 1.
http://www.DBL.com FXS+FXO Gateway Series Connect a computer or other network device to this port. (Less than 100 mid-range) 3） Power (DC24V/500mA) Connect the 24V/500mA Adapter provided to this power jack. 4） Reset Reset switch, use to start the device or delete the configuration quickly. 1.7.
http://www.DBL.com FXS+FXO Gateway Series 2. Connection 2.1.
http://www.DBL.com FXS+FXO Gateway Series Diagram 2-1 Interface Name Connect to Notes FXO 1-4 Connected to four telephone lines If exposed, note lightning FXS 1-4 FXS output, connected to telephone Length of line is below than 300 meters LAN Network input, connected to Network 10/100Base T PC Network output, connected to computer 10/100Base T DC24V Connected to power RESET Restore the factory configuration Press(more than 10 seconds)will ok 2.2.
http://www.DBL.com FXS+FXO Gateway Series Diagram 2-2 Name Explanation Power Power LED Post-Long after start Working status lights Logged, flash 250 ms; login, slow flash 500 ms; upgrading, Continuous flashing 100 ms.
http://www.DBL.com FXS+FXO Gateway Series Diagram 2-3 HTM series have a LAN port and a PC port. Please connect as follows: 1. Open the package, there are a Gateway, a power, and a cable; 2. Take out of Ethernet cable and connect to the PC; 3. The PC supports Network share, connect to the computer or lower switch; 4. FXS is connected to normal telephone, FXO is connected to line PSTN. Make transformer output terminal. 3. Configuration 3.1.
http://www.DBL.com FXS+FXO Gateway Series Username admin Password admin LAN Network Setting DHCP PC Network Setting Bridge mode LAN IP *00(Chinese) *01(English) Press “*00” or “*01” get IP address LAN IP Setting *03 Such as *03192*168*1*2# Restore factory *11983185922 After input password and hear “Toot”, then success, you just to pull power and restart the Gateway. Please remember the password after change 3.2. Logon to the Gateway 3.2.1.
http://www.DBL.com FXS+FXO Gateway Series If the connection is correct, the Web Browser will prompt you to enter the “User name” and “Password” as shown below.
http://www.DBL.
http://www.DBL.com FXS+FXO Gateway Series State of HTM-442 Sequence number: The Gateway factory serial number; Software version number: HTM series’ software version.
http://www.DBL.com FXS+FXO Gateway Series 3.3 Gateway Configuration Click “Configure”, enter interface, and start to configure: 3.3.1. User options A) Language Enter the language page, you can configure it.
http://www.DBL.com FXS+FXO Gateway Series the Pacific Standard Time is GMT-8, while Pacific daytime is GMT-7. Time Zone shows the place where users are, only fill it correctly, CND and billing information can show the right time. C) Time Server Server address that the Gateway get Network time by Internet. The default is: pool.npt.org. D) Auto Provision Choose “Enable” and fill the server IP, if service provider do not support the service, then choose “Disable”, which make setting start-up speed fast.
http://www.DBL.com FXS+FXO Gateway Series It is dialing tone and ring back tone, and so on. You can choose different tone according to different countries. G) China Phone Code Matching Can match all the China phone code and make sure the fastest dial time. H) Reboot Time The Gateway will reboot within the specified time, in order to clean the equipment cache, and make sure the device running normally. 3.3.2.
http://www.DBL.com FXS+FXO Gateway Series When choose Hand Set, click “standard IP” and fill the IP address, mask and Gateway address. When use standard IP, you should fill in “Main DNS” server-address to get Domain Name Service, getting this address you can consult your Internet access service providers. When need to use PPOE, click it, and input the Username and password.
http://www.DBL.com FXS+FXO Gateway Series When use PPOE, need to enable Gateway routing, so that the PC that connected to the Gateway can connect to the Internet correctly. Change the PC Bridge Mode into Standard IP, configure as follows: PC port enables standard IP, the mask 2555.2555.2555.0, after enable DHCP, the computer that connected to the PC port can get arbitrary IP in the range of start address and end address.
http://www.DBL.com FXS+FXO Gateway Series HTM has PSTN and FXO mode, which can be chosen in the FXO Mode pattern: PSTN: In this mode, HTM series gateway’s FXO ports will work like a PSTN by Pass port; you can choose PSTN phone or VOIP channel through star commands *12 or *21 to switch between normal telephone and VOIP. FXO: In this mode, HTM series gateway’s FXO port will work with FXO port state; 3.3.3.1.1 FXS Configuration Click “FXS Setting”, expand the page, configure all the parameters: 1.
http://www.DBL.com FXS+FXO Gateway Series HTM-222 HTM_442 3. As indicated in Figure, when choose H.323 protocol, you should choose “H.323 Terminal”. When several lines use the same number, choose “Single server mode”, when each line choose different numbers, choose “By wiring”. When choose “By wiring”, each line can login to different servers. A) H.323 telephone number Composed by a group of decimal number, use to certain the number in the Network.
http://www.DBL.com FXS+FXO Gateway Series B) H.323 ID A mode of account certification, users can fill according to the service provider. C) Gatekeeper address Use to find right Gatekeeper, fill the IP: 192.168.2.1 or domain: gk yourisp.com. If your port is not the standard (1719, 1720), you can add the special port in the back of the IP or domain, for example: login with 7300: 192.168.2.1:7300 or gk yourisp.com:7300. Notes: Any character of the parameters should be filled with ASCII.
http://www.DBL.com FXS+FXO Gateway Series HTM-222 HTM-442 3.3.3.1.
http://www.DBL.com FXS+FXO Gateway Series A) Single Configure: User can make several VOIP channel share the same configuration. B) Configure by line: Every VOIP channel can be supported service by different providers, also login 2 or 4 telephone numbers on the same server, each number is bundled with corresponding VOIP channel. C) Configure by group: In this mode, each group can bundled one or several lines, each line can exist in different groups. That is each line could login on 4 servers.
http://www.DBL.com FXS+FXO Gateway Series A) RAS Port RAS is communications protocol of Terminal and Gatekeeper, and state information of transferring login information, login information, broadband, and the relationship of the 2 H.323. This option can designate the UDP of this protocol, can be used by the router's port mapping. B) Call signaling port (Q.931) H.225-Q931 is call-control protocol of H.323, use to transfer the call-setting and uninstall information between the 2 H.323.
http://www.DBL.com FXS+FXO Gateway Series 1) Inband DTMF This style makes the special dial-tone together with talk-tone and transfer out without any treatment. So Inband only has one way to set DTMF signaling. 2) Outband DTMF This style uses special methods and transfers the dial-tone to certain the correctness. The special methods are the called protocol, such as RFC2833.
http://www.DBL.
http://www.DBL.com FXS+FXO Gateway Series HTM-442 Click FXS Configuration, expand the configuration interface, and set all the parameter of the HTM_442. Two kinds of VOIP Channel formats: 1) By wiring; 2) Single-server mode. The default is “By wiring”, as following figure: In this mode, there are more advance settings of VOIP Channel. At first, the four VOIP channels can be supported service by different providers.
http://www.DBL.com FXS+FXO Gateway Series F) Certification ID Use to fill the certification account that the Gateway logins on the SIP registration server. G) Password Use to fill the certification password when the Gateway logins on the SIP registration server. H) Display Name When you call your friend John, then his phone will show you call. I) Backup Server Use to register backup, when user have a Backup registration server, then can choose this option.
http://www.DBL.com FXS+FXO Gateway Series 3.3.3.3.2. FXO Configuration Click FXO Configuration, open the interface, setting mode is the same as FXS. When VOIP inbound, it will adapter to PSTN; if PSTN inbound, then adapters to VOIP.
http://www.DBL.
http://www.DBL.com FXS+FXO Gateway Series 3.3.3.3.3. Configuration Mode When choose FXO, the configuration mode of FXS VOIP channel: 1) Single configure; 2) Configure by line; 3) Configure by group A) Single Configure: User can make several VOIP channel share the same configuration. B) Configure by line: Every VOIP channel can be supported service by different providers, also login 2 or 4 telephone numbers on the same server, each number is bundled with corresponding VOIP channel.
http://www.DBL.com FXS+FXO Gateway Series This style makes the special dial-tone together with talk-tone and transfer out without any treatment. So Inband only has one way to set DTMF signaling. 2) Outband DTMF This style uses special methods and transfers the dial-tone to certain the correctness. The special methods are the called protocol, such as RFC2833.
http://www.DBL.com FXS+FXO Gateway Series (5500-5520). B) RTP Packet Length The default time length of each wet packet is 20ms. Use to designate the size of media-packet, the unit is sampling time ms. C) Jitter delay processing mode Use to designate Jitter delay buffer algorithm model. Adaptive mode is the best, other modes are used for test, please do not use in the practical action. D) Media Encryption a) None: Not encrypted.
http://www.DBL.com FXS+FXO Gateway Series 3.3.3.4. Firewall Traversal In the advanced configuration of call settings, signal and media each has firewall configuration. 3.3.3.4.1. H.323 Signaling NAT Traversal There are four styles as follows: A） None Select None to turn off this feature. B) Nat Citron Citron is a dedicated firewall penetration agreement for GNUGK. C) Port Transparent/DMZ Port Transparent refers that put network port of the LAN into computer or inside of the LAN.
http://www.DBL.com FXS+FXO Gateway Series 3.3.3.4.2. SIP Signaling NAT Traversal SIP Signaling NAT Traversal has 3 kinds: A) None Select None to disable this feature. B) STUN （RFC 3489） STUN (Simple Traversal of UDP (User Datagram Protocol) through NATS (Network Address Translators)) is a network protocol allowing a client behind a NAT (or multiple NATS) to find out its public address, the type of NAT it is behind and the internet-side port associated by the NAT with a particular local port.
http://www.DBL.com FXS+FXO Gateway Series 3.3.3.4.3. Media NAT Traversal Similar to Signaling NAT Traversal, this feature allows media packets (RTP) to be routed properly in various network environments. A）NONE Select None to disable this feature. B) Port Transparent/DMZ Port Transparent refers that put network port of the LAN into computer or inside of the LAN. The actual servers allow external users enjoy the servers of internal server(FTP、 HTTP、Telnet).
http://www.DBL.com FXS+FXO Gateway Series 3.3.4. FXS Setting HTM-112 HTM-222 HTM-442 Dialing rules: see the dialing rules Hotline: dial number when pull the phone Key Hold: in the state of “Enable call”, you can stop talking by pressing “*42” Key Transfer: Enable and press *41, then input telephone number, you can achieve Call transfer. Call Hold: Enable it.
http://www.DBL.com FXS+FXO Gateway Series Call prequel: Enable call transfer Net off escape: After enable it, when the Net off or fail to login VOIP, FXS mentioned Machine will put up PSTN outline. Use of billing: you can bill all the lines by using DBL technology billing software. Notes: Every line should be set separately. 3.3.5. FXO Setting FXO Setting make users get practical function, its real is making calls adapter to responding number, and reduce calling time.
http://www.DBL.com b) FXS+FXO Gateway Series As indicated in figure, when IP calls HTM_442, HTM_442 will give beep, only users input the password (1234) correctly can you get PSTN dial-tone and dial. 2. PSTN calls adapters to VOIP special number, fill the adapter number in the “call VOIP adapter number”.
http://www.DBL.com FXS+FXO Gateway Series 3.3.7. Abandon changes If your new settings are not saved, you can clean all the unsaved new parameters. 4. Tools 4.1. Online Upgrade Page shows current version information, input upgrade address, click start, wait after upgrade and start again. When the page shows “Upgrade successful”, click “OK”. Notes: Please keep in touch with the company’s technology support, in case that get the latest information and upgrade address.
http://www.DBL.com FXS+FXO Gateway Series 4.2. Change Password Include “Ordinary user-level” (user) and “Administrator Class” (admin), input the new password two times, click “change” is ok. 4.3. Restore factory settings If you make sure that clean all configurations, click “OK”, wait start again. If not, click “Cancel”, back to current page. Notes: All the users’ personal configuration include new changed password will be cleaned. You also finish these by pressing “RESET” in a long time. 4.4.
http://www.DBL.com FXS+FXO Gateway Series If you are sue to reboot the system, click “OK”, if not, then click “Cancel”, back to current page. Point the “RESET” gently with Small needle-like objects, then HTM_ 442 will reboot. Notes: Press the “RESET” will lead HTM_442 restore factory settings, all the parameters that users configure will be cleaned. 5.
http://www.DBL.com FXS+FXO Gateway Series a. Input“008522343318”，output“008522343318”； b. Input“02083185711”，output“00862083185711”； c. Input“83185700”，output“008675583185700”. 4. Rules：“0:|1 [3-9]:+0|[2-8]:+0755|:+0755”. a. Input“076322343318”，output“076322343318”； b. Input“13044557766”，output“013044557766”； or“13644557766”，output“013644557766” c. Input“23185700”，output“075523185700”. Or“73185700”，output“075573185700” 5.2.
http://www.DBL.com FXS+FXO Gateway Series 6.2. Advanced Configuration There are many configuration option in the advanced configuration, such as Agent Services, Speech Coding sequence and so on, if you familiar with our product, you can configure directly, if not, please view our detailed description, or search our technology support: support@at338.com 6.3.
