得伯乐科技有限公司 DBL Technology Limited GoIP User Manual GoIP Series SIM Card for GSM Voice Gateway User Manual GoIP(GSM VoIP Gateway) Series Version：3.0 2010-10-26 For environmental protection,please view this manual electronically and only print the pages you need Web: www.dbltek.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual Content I. Overview ....................................................................................................................................... 5 1.1 Introduction ............................................................................................................................. 5 1.2 Protocols ................................................................................................................................. 6 1.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 3.3.6 GSM Group Mode ...................................................................................................... 22 3.3.6 Anonymity of the GSM Caller Number ...................................................................... 23 3.3.7 IMEI ............................................................................................................................ 24 3.3.8 SMS Send to Client.......................................................
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 3.5.5 Voice Coding and Sequence ........................................................................................ 48 3.5.6 Firewall Penetration .................................................................................................... 48 3.5.6.1 Traversal of H323 Signaling over NAT ......................................................... 48 3.5.6.2 Traversal of SIP Signaling over NAT .......................................................
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 3.13.3 Restore Factory Settings ........................................................................................... 75 3.13.4 Reset.......................................................................................................................... 76 IV. Parameters of Equipment ....................................................................................................... 77 V. Factory Default Parameter Table .........................
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual I. Overview 1.1 Introduction The GoIP series gateway is a broadband relay gateway newly developed by DBL Technology. It is a new product for seamless connection between the GSM network and VoIP network. When the mobile phone SIM card is installed in the GoIP, users can register the GSM phone to the VoIP softswitch system. Through the GoIP, users can realize the uplink and downlink calls between the GSM network and the VoIP network.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 1.2 Protocols TCP/IP V4 (IP V6 automatic adaptive) ITU-T H.323 V4 standard H.2250 V4 standard H.245 V7 standard H.235 standard (MD5, HMAC-SHA1) ITU-T G.711 Alaw/ULaw, G.729A, G.729AB, G.723.1 and GSM voice coding RFC1889 real-time digital transmission protocol Firewall penetration technology SIP V2.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 1.4 Software Feature LINUX OS Embedded HTTP that accesses internal parameters PPPoE dialing NAT broadband routing function DHCP client DHCP server Software online upgrade Automatic calling Supporting multiple languages Supporting outgoing SMS calls 1.5 Product Package List 1). A GoIP gateway 2). 12V/2A DC(For GoIP_4) or 12V/3A DC (For GoIP_8) transformer 3). An Ethernet cable (2 m) 1.6 Product Appearance Web: www.dbltek.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual Web: www.dbltek.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 1) LAN The network input port that is connected to the router, Modem, and switch; 2) PC The network output port that is connected to network sharing equipment (less than 100 terminals) 3) 12V/2A DC (For GoIP_4) or 12V/3A DC (For GoIP_8) transformer The output terminal that connects the transformer equipped with delivery 4) Reset The reset switch for quick restart of the GoIP. Web: www.dbltek.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual II. Installation 2.1 Installation Procedure The GoIP has 1/8 SIM card slots, an LAN port, and a PC port. The installation procedure is as follows: 1. Open the bottom cover of the GoIP and insert an SIM card of the local GSM network; 2. Connect the LAN port with the upper-layer network equipment with the Ethernet cable; 3. PC port supports network sharing, so connect the PC port to the computer or lower-layer switch (HUB or router); 4.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual Web: www.dbltek.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 2.3 LED Indicators Web: www.dbltek.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual The description of LED indicators is as follows. Description LED Power This indicator is constantly ON after connected with power. indicator LAN indicator This indicator is ON after connected with the network equipment and blinks during data transmission. PC indicator This indicator is ON after connected with the network equipment and blinks during data transmission. 1. The RUN indicator blinks once every 100ms during RUN indicator startup. 2.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual the LAN port info to the mobile phone. ii. When performing reset/reboot through the SMS, the password authentication is required. The password is identical with that of the admin. The detailed procedure is as follows: a. The keyword “reset” and “reboot” is case insensitive, but the password is case sensitive. b. When the reset instruction is sent, the GoIP will automatically reboot. To perform reset, the admin password of GoIP user is “tengda”.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual III. Page Setting Before setting the page, you need to have the IP address of the PC port of the gateway first. Connect the computer for setting the gateway to the PC port of the GoIP. The GoIP gateway has a built-in page server that is used to accept or obtain the HTTP. You can set the related functions for the GoIP through the Internet Explorer. 3.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual Click “OK” button and the gateway status page is displayed as default. GoIP Status Interface Web: www.dbltek.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual GoIP_4 Status Interface GoIP_8 Status Interface The GoIP gateway adopts the tree structure. The menu is on the left and the setting parameters Web: www.dbltek.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual are on the right, as shown in the above figure. You can also access the setting page of the GoIP through the IP address 192.168.2.216 or 192.168.2.172 of the LAN port of the gateway. The login method is the same as that of the PC port, but you must first obtain the IP address of the LAN port. 3.2 Status The status page contains the following contents, as shown in the above figure: 3.2.1 Telephone Information A.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual It displays the current IP address of the PC port. C. PPPoE dialing It displays the PPPoE broadband connection condition. After the connection, the IP address obtained is displayed on the LAN port. D. Default Route It displays the current gateway address. E. Domain Name Server (DNS) It displays the current DNS address. 3.3 User Options Click “User Options” and the following figure shows. User Options of the GoIP Web: www.dbltek.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual User Options of the GoIP_4 / GoIP_8 3.3.1 Language To select a language, refresh the page to enter the language page required. For example, the current language is simplified Chinese. If you wish to display the page in English, click “English” in the menu. After your terminal is restarted, all the pages will be displayed in English. You can also use other languages for setting, as shown in the following figure.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 3.3.3 DTMF Minimum Detection Interval This parameter is used to set the minimum interval of two DTMF signals. Packets may be lost during the data transmission over the GSM. As a result, a DTMF may be incorrectly identified as two or multiple identical DTMFs when detected by the GoIP. The problem of repeated code can be solved effectively through the modification of the parameter.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual In the following figure, the remote control server is set as 118.142.51.162. The terminal user presses *20# and a long tone is heard, which indicates that the instruction has been successfully sent. The remote administrator access http://118.142.51.162:8086 and the model and SN of the gateway are displayed. Click the gateway SN to set the remote gateway. Note: It is a special server, which needs the support of the specific system.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual Each GoIP can operate in any of the following modes: Prohibit: This mode is used when the GoIP operates independently. Serve as the server: When GoIP operates in this mode, the administrator only needs to provide the user with a GSM number of the GoIP as a unique access number to the GoIP group. In one GoIP group, only one GoIP gateway can be used as the server.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual GSM Caller Number option of Goip4 and Goip8 is at Call Divert. Follow the picture. The caller number can be hidden, but this needs the support of the GSM operator. 3.3.7 IMEI The IMEI (International Mobile Equipment Identity) is an electric serial number containing 15 digits. 3.3.8 SMS Send to Client The SMS server sends the request to the mobile phone via the GoIP, or the mobile phone sends the request to the SMS Server via GoIP.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual Technology (The software can be downloaded from the DBL website or obtained from our technical personnel). SMS server port: It is the SMS port of the SMS server. The default value is 44444. It must be consistent with that of the server if modified on the server. Authentication ID: It is the user ID. Make sure that the server has corresponding ID. Authentication password: It is for filling the user password.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 3.3.10 IVR By default, the IVR is enabled. When a call comes in, the system prompts the user to dial a second time. When the IVR is disabled, the system will not prompt the user to dial a second time. 3.3.11 Prompt Tone System The prompt tones are the combination of the intervals and frequencies of the dialing tones and ring-back tones when users hook off the telephone.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual The setting parameters are defined as follows: Each prompt tone involves the following parameters. If a parameter is not defined, the value of the parameter shall be 0.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 3.4 Network Setting Click the “Network Setting” in the menu on the left, and the following page is displayed: 3.4.1 LAN Port Setting The LAN port of the GoIP can be set to the dynamic IP through DHCP, fixed IP, and PPPoE dialing. There are three setting modes: A. Dynamic IP (DHCP) This setting is default.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual Set these parameters according to the network the user uses. C. PPPOE PPPoE (Point-to-point protocol over Ethernet) is a network protocol that compresses the PPP in the Ethernet. Select PPPoE dialing, and enter the account and password provided by the network provider. D. 802.1q VLAN When the network serving the user provides the VLAN service, enter the parameter as required. E.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 3.4.2 PC Port Setting The PC port can be set to connect other network equipment through the route or bridging mode. The two setting modes are as follows: A. Bridging When the PC port is set to the bridging mode, the relation between the LAN port and the PC port is layer 2 switching. The network equipment connected with the PC port same as the connection with the LAN port. B.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 3.4.3 Main DNS The DNS (domain name system) is a database that stores the Internet names and addresses, and converts between the name and the common Internet protocol digits. The main DNS is the IP address of the main DNS (such as 202.67.156.221 or obtain from the service provider). If the PPPoE is set, the main DNS will be automatically provided by the service provider. This parameter can be null. 3.4.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual follows: A. H.323 Telephone Number The value of this parameter is a decimal numeral string that is used to confirm the telephone number in the telephony network. For example, 5551234 is a valid telephone number. Enter the telephone number in this parameter. B. Display Name This parameter is used to display the name of the user who subscribes the H.323 service.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 3.5.1.2 Gatekeeper Under the Gatekeeper mode, the GoIP operates in the H.323 register status. When you register through the H.323 protocol, select “H.323 Terminal” in “Terminal Type”, as shown in the above figure. The registration mode involves the Gatekeeper and direct connection (the direct connection mode is used for calls over the IP address). When all lines use one number, select the single server setting mode.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual This parameter is used to display the name of the user who subscribes the H.323 service. For example, when you call your friend John Smith, your name will be displayed on your friend’s telephone. D. H.323 ID H232 ID is used to verify the account. You can enter this parameter according to the requirements of the service provider. E. Gatekeeper Address This parameter is used to find the proper Gatekeeper. Enter the IP address of the Gatekeeper, such as 192.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 3.5.1.3 Advance Setting of the H.323 The advance option of the GoIP involves the signaling and media, corresponding to “Advance Setting” and “Media” respectively. Select “Advance Setting” under H323, and the following setting page is displayed: A. RAS Port The RAS is the communication protocol between the terminal and the Gatekeeper. It is used to transmit the registration information, login, broadband change, and the status between two H.323 unites.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual to detect and solve the compatibility problem. If you are not sure, do not set this parameter. E. Fast Start Extension This parameter is set for the special requirement of some customers. If you are not sure, do not set this parameter. F. H245 Tunnel This parameter is set for the special requirements of some customers. If you are not sure, do not set this parameter. G.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual G. Signaling QoS Quality of Service (QoS) is a network’s capacity to provide priority services, including the special bandwidth, jitter control and delay (used for real-time and interactive traffic), and improvement of the packet loss ratio. This parameter is used to mark the specified QoS label for the call signaling packet to increase the network service quality. 3.5.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 3.5.2.2 Single Server Mode The setting parameters relating to the SIP are as follows: A) Telephone Number This parameter is used to set the telephone number of the line. The telephone number is a unique ID when the gateway serves as the callee. B) SIP Proxy Server This parameter is used to set the address of the SIP proxy server.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 192.168.2.26:3000 or hy.con.com:3000. D) Outbound Proxy The outbound proxy is mainly used in the scenarios where the firewall or NAT exists, so that the signaling and media stream can penetrate the firewall. E) Homing Domain This parameter is used for the domain management host of the SIP (a host that provides the SIP service). F) Authentication ID This parameter is used to set the authentication account when the gateway logs into the SIP proxy server.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 3.5.2.3 Setting by Line ( Valid for the GoIP_4 and GoIP_8) GoIP_4 config by line Web: www.dbltek.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual GoIP_8 config by line You need to set parameters for each line and the setting method is the same. The setting parameters are as follows: A) Telephone Number This parameter is used to set the telephone number of the line. The telephone number is an unique ID when the gateway serves as the callee. B) Gateway Prefix The gateway prefix enables the connection of calls through a particular line. It can match the first digit only.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual C) SIP Proxy Server This parameter is used to set the address of the SIP proxy server. If the SIP proxy server uses the special port (other than the SIP default port 5060), you can add the detailed port number at the end of the IP address or domain name of the proxy server. For example, 192.168.2.26:3000 or hy.con.com:3000. D) SIP Registration Server The SIP login server is a server that the gateway registers the account.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual This parameter is used for registration backup. When a backup registration server exists in the user’s system, the user can enable this parameter. When the backup server is enabled, the gateway will automatically log into the backup server in case of the failure of the main server. 3.5.2.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual C) SIP Trunk Gateway3 It is the IP address of the server connected to the GoIP gateway. D) Telephone Number This parameter is used to set the telephone number of the line. The telephone number is an unique ID when the gateway serves as the callee and takes effect when the GoIP logs into the SIP Trunk Gateway1.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual A. Signaling Port (SIP Local Port) The SIP local port is the local UDP port. It is used for communications between the SIP agent and the SIP proxy server as well as other SIP managers. B. NAT Hold This parameter is used to hold the port that is activated by the NAT for SIP signaling communication. The unit of the parameter is m. C. Timeout Setting E.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual special bandwidth, jitter control and delay (used for real-time and interactive traffic), and improvement of the packet loss ratio. This parameter is used to mark the specified QoS label for the call signaling packet to increase the network service quality. F. DTMF Signals DTMF signals are used to transmit call signals to the call switching center over the audio band.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual Setting” > “Media” and the following setting parameters are displayed: A. RTP Port (Range) This parameter is used to specify the UDP of the RTP and used with the router port for mapping. Note: The terminal will use multiple pairs of RTPs (depending on the number of lines that the terminal supports). The value of this parameter ranges from 5500 to 5520. B. Packet Length(ms) This parameter indicates the duration of sending a network packet.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual improvement of the packet loss ratio. This parameter is used to mark the specified QoS label for the voice packet to increase the network service quality. Note: For details about media encryption and media NAT penetration, refer to 3.5.6 Firewall penetration. 3.5.5 Voice Coding and Sequence This parameter is used to modify the compression coding according to the requirements of the service provider.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual A. No The mechanism of firewall traversal is not supported. B. Nat Citron The Citron is a special firewall traversal protocol for GnuGK and used with GnuGK. C. Port Transparency/DMZ The port transparency is used to transfer the network port on the LAN interface to the computer or the server in the LAN. This feature enables external users (through the Internet in most cases) to share the services of internal servers (such as FTP, HTTP, and Telnet).
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual Note: This feature needs the support of the server developed by DBL Technology. 3.5.6.2 Traversal of SIP Signaling over NAT The traversal of SIP signaling over NAT (firewall) is classified into: A. No The mechanism of firewall traversal is not supported. B. STUN (RFC 3489) The Simple Traversal of UDP over NAT (STUN) is a protocol that enables the SIP phone to detect the existence and type of the firewall installed in the computer.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 3.5.6.3 Media NAT Traversal The media NAT (firewall) traversal is classified into four types: A. No firewall The firewall traversal mechanism is not supported. B. Port Transparency/DMZ The port transparency is used to transfer the network port on the LAN interface to the computer or the server in the LAN. This feature enables external users (through the Internet in most cases) to share the services of internal servers (such as FTP, HTTP, and Telnet).
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual supporting the transit over the specified port (supported by the relay server later than V2). 3.5.7 Dialing Rule The GoIP supports number dialing by rules. You can specify dialing rules in the dialing rule parameter of the “Call Forwarding”. 3.5.7.1 Format of Dialing Rules 1. You can specify multiple rules, which are separated by the delimiter ‘|’. For example, “00:-00|0:-0+86|:+86755”. 2.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 3. Rule: “00:|0:-0+0086|:+0086755” a. The input number is “008522343318” and the output number is “008522343318”. b. The input number is “02083185711” and the output number is “00862083185711”. c. The input number is “83185700” and the output number is “008675583185700”. 4. Rule: “0:|1[3-9]:+0|[2-8]:+0755|:+0755” a. The input number is “076322343318” and the output number is “076322343318”. b.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual the telephone number. However, the length of the mobile phone number is limited to 11 digits. As shown above, the length of telephone numbers is limited to eight digits. 13[0-9]xxxxxxxx and [1-8]xxxxxxx represent mobile phone numbers 130xxxxxxxx to 139xxxxxxxx, and telephone number 1xxxxxxx to 8xxxxxxx, respectively.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual numbers. Therefore, set this parameter carefully. The adjustment on the input/output volume is for VoIP lines. 3.7 Call Forwarding (Setting on the Call Route and Authentication Mode) The gateway provides the call routing function for users, which can be set in the Call Forwarding Setting. The call routing is to forward calls to specified numbers, so that the dialing time can be decreased.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 3.7.2 Authentication Mode Setting The authentication mode is classified into the password authentication, trust list authentication, and password or trust list authentication. Downlink (VoIP to PSTN) authentication mode Uplink (PSTN to VoIP) authentication mode 3.7.2.1 Password Authentication The setting is as follows: Select “Forward to PSTN Authentication Mode” > “Password Authentication”. Enter the password in “Call PSTN Authentication Password”.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual The setting is as follows: Select “Forward to PSTN Authentication Mode” > “Trust List Authentication”. Click the “VoIP Trust Number List”, and the VoIP Trust Number List is displayed (Maximum 15 trust numbers can be entered). Enter the trust VoIP number in trust number sequence. If only a VoIP trust number, such as 3306, is set, only the number 3306 can be used to dial the PSTN from the VoIP.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual 3.8 Call Duration Limit The call duration limit is to limit the call duration of SIM cards in the gateway. Through this function, you can specify the total call duration of SIM cards. When the call duration is longer than the specified value, the calls shall not be connected to prevent the unnecessary or unsafe call charging.
得伯乐科技有限公司 DBL Technology Limited SIM Card Call Duration Setting GoIP User Manual SIM Card Remaining Call Duration The setting is same as the SIM card time limit diagram. The total call duration of the SIM card is 30 minutes. When the call duration is less than or equals 10 minutes, the gateway will send a short message to 13713652130 (the SIM card ID is 2130 in the reporting message.) to report the remaining call duration.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual A: Mode 1 In this mode, the GoIP sets the calling number of the SMS as the calling number of the call and the called number as the short message content; B: Mode 2 In this mode, the GoIP sets the SIP number of the GoIP as the calling number of the call and the called number as the short message content; C: Mode 3 In this mode, the GoIP sets the SIP number of the GoIP as the calling number of the call and the called number as the short message content and t
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual Mode 1: When a short message of “8675588228822” is sent from the mobile phone number (+86)13800000000 to the GoIP, the GoIP will send the following call request signaling: Sending Message to 192.168.2.1:5060: INVITE sip:8675588228822@192.168.2.1:5060;transport=udp SIP/2.0 Via: SIP/2.0/UDP 192.168.2.237:5060;branch=z9hG4bK363969813 From: ;user=phone;tag=65248630 To:
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual Contact: Max-Forwards: 30 User-Agent: DBL Allow: INVITE, ACK, BYE, CANCEL, OPTIONS, NOTIFY, REFER, REGISTER, MESSAGE, INFO, SUBSCRIBE Content-Type: application/sdp Content-Length: 226 When the user enters an SMS dial prefix, such as 999, the above call request signaling is changed to: Sending Message to 192.168.2.1:5060: INVITE sip:9998675588228822@192.168.2.1:5060;transport=udp SIP/2.0 Via: SIP/2.0/UDP 192.168.2.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual MESSAGE, INFO, SUBSCRIBE Content-Type: application/sdp Content-Length: 226 Mode 2: When a short message of “8675588228822” is sent from the mobile phone number (+86)13800000000 to the GoIP, the GoIP will send the following call requests.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual Max-Forwards: 30 User-Agent: DBL Allow: INVITE, ACK, BYE, CANCEL, OPTIONS, NOTIFY, REFER, REGISTER, MESSAGE, INFO, SUBSCRIBE Content-Type: application/sdp Content-Length: 226 Mode 3: When a short message of “8675588228822” is sent from the mobile phone number (+86)13800000000 to the GoIP, the GoIP will send the following call requests.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual CSeq: 2 INVITE Contact: Max-Forwards: 30 User-Agent:DBL Allow: INVITE, ACK, BYE, CANCEL, OPTIONS, NOTIFY, REFER, REGISTER, MESSAGE, INFO, SUBSCRIBE Content-Type: application/sdp Content-Length: 226 3.9.2 SMS Dialing under the H.323 Protocol The GoIP permits users to dial back through the SMS under the H.323 protocol.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual later version will. ) In this mode, the GoIP sets the H.323 number of the GoIP as the calling number of the call and the called number as the short message content and the number of the short message sender, whose format is short message content*the number of the short message sender. D: SMS Dial Prefix When the GoIP initiates the SMS call, the GoIP will change the prefix number to the called number prefix.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual In this mode, when the GoIP receives the call from the H.323 GK, the GoIP will forward the call to the short message sending equipment through the GSM network.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual callReferenceValue = 7502 conferenceID = 16 octets { 7f f3 78 77 49 3f 4c c1 9a dc 6a 84 12 d8 30 8f ..xwI?L...j...0. } activeMC = FALSE answerCall = FALSE canMapAlias = FALSE callIdentifier = { guid = 16 octets { cb 40 a4 af 8e 9b 60 96 6b 5f a0 03 f2 ed 55 5b .@....`.k_....
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual requestSeqNum = 241 callType = pointToPoint NULL endpointIdentifier = "3705_endp" destinationInfo = 1 elements { [0] = dialedDigits "9998675588228822" } srcInfo = 2 elements { [0] = dialedDigits "20001" [1] = h323-ID "20001" } srcCallSignalAddress = ipAddress { ip = 4 octets { c0 a8 02 ed .... } port = 2049 } bandWidth = 2048 callReferenceValue = 7502 conferenceID = 16 octets { 7f f3 78 77 49 3f 4c c1 9a dc 6a 84 12 d8 30 8f ..xwI?L...j...0.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual activeMC = FALSE answerCall = FALSE canMapAlias = FALSE callIdentifier = { guid = 16 octets { cb 40 a4 af 8e 9b 60 96 6b 5f a0 03 f2 ed 55 5b .@....`.k_....U[ } } gatekeeperIdentifier = "GnuGk" willSupplyUUIEs = FALSE } 3.9.3 SMS Forwarding The GoIP supports the SMS forwarding through the SMS under SIP protocol.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual MESSAGE sip:3999@192.168.2.1 SIP/2.0 Via: SIP/2.0/UDP 192.168.2.162:5060;branch=z9hG4bK1967685528 From: ;tag=667435795 To: Call-ID: 2094144847@192.168.2.162 CSeq: 4 MESSAGE Contact: Max-Forwards: 30 User-Agent: DBL Content-Type: text/plain Content-Length: 28 8613682626865 075583185700 2. The SMS sent to the GoIP from the SIP is forwarded to the specified PSTN number.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual Contact: max-forwards: 16 date: Tue, 18 Nov 2008 06:36:37 GMT user-agent: SIPPER for 3CX Phone p-hint: usrloc applied Content-Type: text/plain Content-Length: 26 13682626800 Hello world Note: The SMS forwarding mode of the GoIP is only functional under the SIP protocol. 3.10 Transparent Transmission of PSTN Caller Numbers The GoIP permits the transparent transmission of PSTN caller numbers to the VoIP system in various methods.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual signaling of the VoIP system. The signaling is as follows (provided that the PSTN caller number is 13800000000): Use CID as SIP caller number: The GoIP directly initiates the call request to the VoIP system through the PSTN caller number and adds the relevant information to Remote Party ID option of the request signaling. The call request signaling is as follows: 3.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual Note: Some of parameters of the gateway will not be valid until the gateway is restarted. Therefore, you are advised to restart the gateway after the parameters are modified, so that the modification can take effect. 3.12 Abandon the change When the new setting is not saved, you can clear all the unsaved parameters. 3.13 Tool Select Menu > Tool. The following page is displayed. 3.13.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual Note: During the upgrading, do not cut off the power. Otherwise, the GoIP will be damaged. 3.13.2 Modification of Password You can modify the password of the user and administrator. Select Tool > Modify Password. The password modification page is displayed, as shown in the following figure. Enter a new password and click “Change”. Then, the password is successfully modified.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual section of “Asterisk Instructions”. 3.13.4 Reset Select Tool > Reset to restart the GoIP. Web: www.dbltek.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual IV. Parameters of Equipment Hardware Parameter Parameter Remark Feature Model GOIP GOIP_4 Customizable Processor ARM9E 133MHz ARM9E 133MHz DSP VPDSP101 95MHz VPDSP101 95MHz RAM 16M 16M FLASH 4M 4M Power DC12V/2A +-10% DC12V/2A +-10% 2 pieces Input 100V to 240V GSM band Default Default 900M/1800M 900M/1800M Optional Optional 850M/1900M 850M/1900M Power Default Customized Max. 5 W Max.
得伯乐科技有限公司 DBL Technology Limited GSM channel GoIP User Manual 1 4 Hardware Feature Parameter Remark Model GoIP_8 Customizable Processor ARM9E 133MHz DSP VPDSP101 95MHz RAM 16M FLASH 4M Power DC12V/3A +-10% Input 100V to 240V GSM band Default Default 2 pieces 900M/1800M Optional Customized 850M/1900M Power consumption Max. 20 W LED RUN, GSM, LAN, PC Network adapter 2 100/10BASE-T Weight 1.
得伯乐科技有限公司 DBL Technology Limited GoIP User Manual V. Factory Default Parameter Table Parameter Netw ork Passw ord Default Value LAN Dynamic IP (DHCP) PC Fixed IP: 192.168.8.1 admin admin user 1234 Default time zone GMT+8 Web: www.dbltek.
